Manufacturer’s warranty ..........................................24 This user’s manual is a main operating document intended for technical, maintenance, and operating staff. The manual contains information about purpose, technical details, operating principle, design, and installation of the Iso-Mix unit and all its modifications.
SAFETY REQUIREMENTS All user’s manual requirements as well as the provisions of all the applicable local and national construction, electrical, and technical norms and standards must be observed when installing and operating the unit. Disconnect the unit from the power supply prior to any connection, servicing, maintenance, and repair operations.
Page 4
noise. Misuse of the unit and any unauthorised modifications are not allowed. Do not expose the unit to adverse atmospheric agents (rain, sun, etc.). Transported air must not contain any dust or other solid impurities, sticky substances, or fibrous materials. Do not use the unit in a hazardous or explosive environment containing spirits, gasoline, insecticides, etc.
Page 5
This unit is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the unit by a person responsible for their safety.
Page 6
Connection to the mains must be made through a disconnecting device, which is integrated into the fixed wiring system in accordance with the wiring rules for design of electrical units, and has a contact separation in all poles that allows for full disconnection under overvoltage category III conditions.
Page 7
Ensure that the unit is switched off from the supply mains before removing the guard. Precautions must be taken to avoid the back-flow of gases into the room from the open flue of gas or other fuel-burning appliances. THE PRODUCT MUST BE DISPOSED SEPARATELY AT THE END OF ITS SERVICE LIFE. DO NOT DISPOSE THE UNIT AS UNSORTED DOMESTIC WASTE.
DELIVERY SET 1 pc. Screws with dowels 4 pcs. Plastic screwdriver (only for the models with a timer) 1 pc. User’s manual 1 pc. Packing box 1 pc. OPERATION GUIDELINES The fan is rated for connection to single-phase AC 220-240 V/50 Hz or 220 V/60 Hz power mains. The fan is rated for continuous operation.
DESIGNATION KEY Iso-Mix 200 T ___ Unit voltage: _ — 220-240 V/50 (60) Hz (by default) YYY V/ZZ Hz — mains parameters other than the default ones Options: T: timer US: speed switch FR1: integrated speed controller from 0 to 100 %, power cord with a mains plug G1: speed controller with an electronic thermostat and external temperature sensor.
INSTALLATION AND SET-UP The fan is suitable both for horizontal or vertical mounting on the floor, on the wall or on the ceiling. While mounting the fan, provide extra protection against water ingress: • In case of vertical mounting, install a protective hood on top. •...
Page 13
Cut off power supply and make sure electricity Lead the power cable to the ventilation hole, drill the has been turned off. Mark the holes for fixing the mounting holes and install the dowels. fan and the power cable. For any mounting position connect an air duct on both Fix the fan with the screws.
Page 14
Cut off power supply and make sure electricity has been turned off. Remove the cover of the fan. Connect the power cord wires to the terminal block and Supply power to the fan. assemble the fan in reverse order.
Page 15
Mounting sequence for different fan models...
Page 17
Iso-Mix ... T Iso-Mix ... US 2 min 30 min STOP Iso-Mix ... G1 (GI1, GT1, GTI1, GS1, GSI1) Iso-Mix ... FR1 Thermostat control knob Speed Speed control knob control knob...
CONNECTION TO POWER MAINS The fan is rated for connection to single-phase AC 220-240 V 50/60 Hz power mains. Terminal designations on wiring diagrams L – line N – neutral Low – minimum speed terminal Mid – medium speed terminal High –...
Page 19
Iso-Mix High speed Medium speed High High Low speed High High High High...
• Make sure the motor has cooled down to operating temperature. • Switch on the power supply. The Iso-Mix ... T fan starts operation when the control voltage is applied to the LT input terminal by an external switch (e.g. switching on the room light).
Page 21
Iso-Mix ... GS(I)1: The fan switches to the set speed as the room air temperature exceeds the set point. As the air temperature drops 2 °C below the set point or if the initial temperature is below the set point, the fan is turned off.
TECHNICAL MAINTENANCE The fan maintenance periodicity is at least once per 6 months. Maintenance steps: Disconnect the fan from power supply and make sure Clean the fan with a soft dry cloth or a brush. electricity has been turned off. Disconnect an air duct on both sides of the fan.
TROUBLESHOOTING Problem Possible reasons Troubleshooting Make sure the power supply line No power supply. is connected correctly, otherwise When the unit is connected to power mains, the fan does not rotate and troubleshoot the connection error. does not respond to any controls. Internal connection fault.
MANUFACTURER’S WARRANTY The product is in compliance with EU norms and standards on low voltage guidelines and electromagnetic compatibility. We hereby declare that the product complies with the provisions of Electromagnetic Compatibility (EMC) Directive 2014/30/ EU of the European Parliament and of the Council, Low Voltage Directive (LVD) 2014/35/EU of the European Parliament and of the Council and CE-marking Council Directive 93/68/EEC.
Page 25
• Redesign or engineering changes to the unit. • Replacement and use of any assemblies, parts and components not approved by the manufacturer. • Unit misuse. • Violation of the unit installation regulations by the user. • Violation of the unit control regulations by the user. •...
Page 27
Quality Inspector’s Stamp Sold by (name and stamp of the seller) Manufacture Date Purchase Date...
Need help?
Do you have a question about the Iso-Mix and is the answer not in the manual?
Questions and answers