LAUNCH TECH X-431 PRO5 User Manual
  1. Manuals
  2. Brands
  3. LAUNCH TECH Manuals
  4. Diagnostic Equipment
  5. X-431 PRO5
  6. User manual

LAUNCH TECH X-431 PRO5 User Manual

Hide thumbs Also See for X-431 PRO5:
Table of Contents

Advertisement

Quick Links

Download this manual
Version: V1.00.000
Revised date: 07-30-2021

Advertisement

Table of Contents
loading

Related Manuals for LAUNCH TECH X-431 PRO5

Summary of Contents for LAUNCH TECH X-431 PRO5

  • Page 1 Version: V1.00.000 Revised date: 07-30-2021...
  • Page 2 X-431 PRO5 User Manual Copyright Information Copyright © 2021 by LAUNCH TECH CO., LTD (also called LAUNCH for short). All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording or otherwise, without the prior written permission of LAUNCH.
  • Page 3 LAUNCH X-431 PRO5 User Manual Using This Manual This manual contains device usage instructions. Some illustrations shown in this manual may contain modules and optional equipment that are not included in your system. The following conventions are used. Bold Text Bold text is used to highlight selectable items such as buttons and menu options.
  • Page 4 LAUNCH X-431 PRO5 User Manual Illustrations Illustrations used in this manual are samples, the actual testing screen may vary for each vehicle being tested. Observe the menu titles and on-screen instructions to make correct option selection. Important Safety Precautions To avoid personal injury, property damage, or accidental damage to the product, read all of the information in this section before using the tool.
  • Page 5 LAUNCH X-431 PRO5 User Manual ignition wires and spark plugs. These components create hazardous voltage when the engine is running.  To avoid damaging the tool or generating false data, please make sure the vehicle battery is fully charged and the connection to the vehicle DLC (Data Link Connector) is clear and secure.
  • Page 6 LAUNCH X-431 PRO5 User Manual FCC Statement Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the...

  • Page 7: Table Of Contents

    LAUNCH X-431 PRO5 User Manual TABLE OF CONTENTS 1 Introduction ....................1 1.1 Product Profile ..................1 1.2 Components & Controls ................. 3 1.2.1 Display Tablet .................. 3 1.2.2 VCI Device ..................4 1.3 Technical Parameters ................7 1.4 Package List ................... 8 2 Initial Use ....................10...
  • Page 8 LAUNCH X-431 PRO5 User Manual 5.1 Intelligent Diagnose ................22 5.2 Local Diagnose ..................25 5.2.1 Health Report (Quick Test) ............30 5.2.2 System Scan ................. 34 5.2.3 System Selection ................34 5.3 Remote Diagnose ................. 45 5.3.1 Add Friends ................... 46 5.3.2 Start Instant Messaging ..............
  • Page 9 LAUNCH X-431 PRO5 User Manual 7.1 Update Diagnostic Software & APP ............60 7.2 Update Frequently Used software ............61 7.3 Renew Subscription................61 8 Add-on Modules ..................64 8.1 ADAS (Calibration) ................64 8.2 TPMS ....................64 8.3 BST360 (Battery Tester) ............... 64 8.4 Videoscope...................
  • Page 10 LAUNCH X-431 PRO5 User Manual 9.12 Diagnostic Software Clear ..............74 10 J2534 Programming .................75 10.1 Working principle ................75 10.2 Connection ..................75 10.3 Install the software & driver ..............77 11 FAQ ......................78...

  • Page 11: Introduction

    LAUNCH X-431 PRO5 User Manual 1 Introduction 1.1 Product Profile This Android OS-based, tablet-style diagnostic tool incorporates the best possible coverage of OE-level diagnostics with multitasking capable software. Using the powerful 8-core 1.8GHz processor and a 10.1 inch IPS capacitive...
  • Page 12 LAUNCH X-431 PRO5 User Manual normal use and only works with the specific ADAS calibration tool.  TPMS: Configures the tool as a professional Tire Pressure Monitoring System (TPMS) service tool. It needs to work with the TSGUN device (sold separately) to perform all kinds of various TPMS functions.

  • Page 13: Components & Controls

    LAUNCH X-431 PRO5 User Manual 1.2 Components & Controls There are two main components to the diagnostic system:  Display Tablet – the central processor and monitor for the system (See Chapter “1.2.1”).  VCI Device – the device for accessing vehicle data (See Chapter “1.2.2”).

  • Page 14: Vci Device

    LAUNCH X-431 PRO5 User Manual the tablet on. In On mode: • Press it once to activate the LCD if the LCD is off. Press it once to turn off the LCD if the LCD lights up. • Press and hold it for 3 seconds to turn it off.
  • Page 15 LAUNCH X-431 PRO5 User Manual • When working with a PC, it acts as a J2534 Pass-thru device to perform the J2534 programming. For more details, refer to Chapter 10. The LEDs enable you to easily identify the working status of the module.
  • Page 16 LAUNCH X-431 PRO5 User Manual Diagnostic socket Connect the diagnostic cable. Identify the working status of the VCI. It is defined as follows:  Power: It illuminates solid red when the VCI is powered on.  Vehicle: While communicating with the LEDs vehicle, it lights up and flashes.

  • Page 17: Technical Parameters

    LAUNCH X-431 PRO5 User Manual to the PC via data cable.  Wireless: It lights up when the VCI is working in wireless communication mode. Connect to the VCI device to perform J2534 Data I/O port programming operations. Reset hole Reset the VCI.

  • Page 18: Package List

    LAUNCH X-431 PRO5 User Manual Dimension: 200mm x 75mm x 40mm 1.4 Package List The following packing list is for reference purpose only. For different destinations, the accessories may vary. For details, please consult from the local dealer or check the packing list supplied with this tool together.
  • Page 19 LAUNCH X-431 PRO5 User Manual receptacle. For different vehicle diagnostic socket, it may be necessary to use one of the non-16pin connectors included within Non-16pin adaptor (Optional) the kit. cable kit For detailed non-16pin connectors, please check the package box.

  • Page 20: Initial Use

    LAUNCH X-431 PRO5 User Manual 2 Initial Use 2.1 Charging & Turning On 1. Use the included power adaptor to charge the tablet. 2. After charging is complete, press the POWER button to turn the tablet on. The system starts initializing and then enters the home screen.

  • Page 21: Change System Language

    LAUNCH X-431 PRO5 User Manual Slide: To jump to different pages. Drag: Tap the application icon and drop it to other location. Spread apart/pinch together: To zoom in manually, place two fingers on the screen and then spread them apart. To zoom out, place two fingers apart on the screen and then pinch them together.

  • Page 22: Network Setup

    LAUNCH X-431 PRO5 User Manual 2.7 Network Setup The tablet has built-in Wi-Fi that can be used to get online. Once you’re online, you can register your tool, surf the Internet, get apps, send email, launch the remote diagnosis, and check for software updates etc.

  • Page 23: Getting Started

    LAUNCH X-431 PRO5 User Manual 3 Getting Started For new users, you will need to experience a user registration process before getting started. 3.1 Register & Update Follow the steps below to proceed registration and update: Tap the application icon on the home screen to launch it, and then tap Login to enter the login interface of diagnosis software.
  • Page 24 LAUNCH X-431 PRO5 User Manual Fill in the information in each field (Items with * must be filled). After inputting, tap Register, the following screen will appear: Input the 12-digit Product Serial Number and 8-digit Activation Code (can be obtained from the password envelope), and then tap Activate.

  • Page 25: Job Menu

    LAUNCH X-431 PRO5 User Manual No to ignore it. In this case, follow Chapter 7 to check for updates. After the registration is successfully complete, the wireless communication between the tablet and the VCI device is automatically established and user has no need to configure it again.
  • Page 26 LAUNCH X-431 PRO5 User Manual Perform commonly used repair & maintenance Service Function services. This option aims to help repair shops or technicians Remote Diagnose launch instant messages and remote diagnosis, making the repair job getting fixed faster. Configures this tool as a professional TPMS (Tire Pressure Monitoring System) service tool.

  • Page 27: Diagnostics Toolbar

    LAUNCH X-431 PRO5 User Manual 3.3 Diagnostics Toolbar The diagnostics toolbar contains a number of buttons that allow you to print the displayed data or make other controls. It is displayed on the upper right corner of the screen and goes through the whole diagnostic session. The table below...

  • Page 28: Connections

    LAUNCH X-431 PRO5 User Manual 4 Connections 4.1 Preparation  The ignition is turned on.  The vehicle battery voltage range is 11-14 volts or 18~30 volts.  The throttle is in the closed position.  Find DLC location. 1. For Passenger Vehicles, The DLC(Data Link Connector) is usually located 12 inches from the center of the instrument panel, under or around the driver’s side for most vehicles.

  • Page 29: Vehicle Connection (Only For Passenger Vehicle Configuration)

    LAUNCH X-431 PRO5 User Manual 4.2 Vehicle Connection (Only for Passenger Vehicle Configuration) The method used to connect the VCI device to a vehicle’s DLC depends on the vehicle’s configuration as follows:  A vehicle equipped with an OBD II management system supplies both communication and 12V power through a standardized DLC.

  • Page 30: Vehicle Connection (Only For Commercial Vehicle Configuration)

    LAUNCH X-431 PRO5 User Manual A. Battery Clamps Cable (optional): B. Cigarette Lighter Cable (optional): 4.2 Vehicle Connection (Only for Commercial Vehicle Configuration) 4.2.1 OBD II vehicle Connection Use the included OBD II extension cable to connect the VCI to the vehicle’s DLC...

  • Page 31: Non-Obd Ii Vehicle Connection

    LAUNCH X-431 PRO5 User Manual 4.2.2 Non-OBD II vehicle Connection For non-OBDII commercial vehicle, refer to the following connection method to proceed.

  • Page 32: Diagnosis

    LAUNCH X-431 PRO5 User Manual 5 Diagnosis 5.1 Intelligent Diagnose Through simple Bluetooth communication between the display tablet and VCI, you can easily get the VIN (Vehicle Identification Number) information of the currently identified vehicle. Once the VIN is successfully identified, the system will retrieve it from the remote server and then guide you to vehicle information page without the necessity of step-by-step manual menu selection.
  • Page 33 LAUNCH X-431 PRO5 User Manual • Tap “Maintenance record” to view its historical repair record. If there are records available, it will be listed on the screen in sequence of date. If no records exist, the screen will show “No Record”.
  • Page 34 LAUNCH X-431 PRO5 User Manual Place the VIN inside the viewfinder rectangle to scan it. The most recognizable location for this number is in the top left corner on the vehicle’s dashboard. Other locations include the driver’s door or post, and the firewall under the hood.

  • Page 35: Local Diagnose

    LAUNCH X-431 PRO5 User Manual • If the VIN scanned is incorrect, tap the result field to modify it and then tap • To scan it again, tap REPEAT. If the VIN exists on the remote server, the system will enter the diagnostic function selection screen.
  • Page 36 LAUNCH X-431 PRO5 User Manual In this case, camera scan and enter VIN are available. A. Camera Scan: In this mode, the VCI should be connected to the vehicle’s DLC first, and then a Bluetooth communication should be established between the tablet and the VCI.
  • Page 37 LAUNCH X-431 PRO5 User Manual • Tap to choose it from the record list if the VIN of the vehicle has been scanned before. • Tap to input the VIN manually if the tablet has failed to identify the VIN of the vehicle.
  • Page 38 LAUNCH X-431 PRO5 User Manual Input the VIN, and tap OK, the tablet will automatically identify the vehicle model and directly navigate to the diagnostic function selection menu. 2. Tap a corresponding diagnostic software logo, and then follow the on-screen instruction to access the diagnostic software.
  • Page 39 LAUNCH X-431 PRO5 User Manual Introduction: Tap to check the software function list. Note: Tap to read some precautions on using the current diagnostic software. Search Bluetooth: Tap to search for the available VCI. After the VCI is successfully activated, it will be bound to the user account and paired with the tablet automatically.

  • Page 40: Health Report (Quick Test)

    LAUNCH X-431 PRO5 User Manual 4). Read vehicle information: After reading the vehicle information, double check if the vehicle information is correct or not. If yes, tap Yes to continue. 5). Select test item: Select the desired test item to proceed.
  • Page 41 LAUNCH X-431 PRO5 User Manual The tested system with fault code appears in red and the system functioning properly displays in black (normally). Note: Diagnostic Trouble Codes or Fault Codes can be used to identify which engine systems or components that are malfunctioning. Never replace a part based only on the DTC definition.
  • Page 42 LAUNCH X-431 PRO5 User Manual Note: Diagnostic report is classified into three categories: Pre-Repair report, Post-Repair report and Diagnostic Scan. No matter which type you saved the report as, the report type will be appended as a tag on the upper right corner of the diagnostic report for easier identification.
  • Page 43 LAUNCH X-431 PRO5 User Manual tags on the diagnostic report. To ignore the workshop information, tap Skip to go to the report details screen. On the report details screen, tap Save to save it. All diagnostic reports are saved in Report -> Health Report.

  • Page 44: System Scan

    LAUNCH X-431 PRO5 User Manual • You have saved a pre-repair report of the currently tested vehicle, and • You have already made some repairs and service and cleared the DTCs after the pre-repair reported is generated. Otherwise, no differences exist between the pre- and post- repair reports.
  • Page 45 LAUNCH X-431 PRO5 User Manual Swipe the screen from the bottom to view the vehicle system on the next page. Tap the target system (take ECM for example) to navigate to the diagnostic function selection screen. Note: Different vehicle has different diagnostic menus.
  • Page 46 LAUNCH X-431 PRO5 User Manual one part of an overall diagnostic strategy. Never replace a part based only on the DTC definition. Each DTC has a set of testing procedures, instructions and flow charts that must be followed to confirm the location of the problem. This information can be found in the vehicle’s service manual.
  • Page 47 LAUNCH X-431 PRO5 User Manual made, the code(s) will appear again and the check engine light will illuminate as soon as the problem that cause the DTC to set manifests itself. On the diagnostic function selection screen, tap Clear Fault Code, the following screen will appear.
  • Page 48 LAUNCH X-431 PRO5 User Manual On-screen Buttons: Select Page: Tap to select all items of the current page. Select All: Tap to select all items. To select certain data stream item, just check the box before the item name. Unselect: Tap to deselect all data stream items.
  • Page 49 LAUNCH X-431 PRO5 User Manual Here the user can set different display style for each selected item. indicates sticky top. If it is tapped, it will change into . On the data stream display screen, the data stream item with will be shown on the top of the selected data stream list.
  • Page 50 LAUNCH X-431 PRO5 User Manual Graph(Single): Tap to view the parameter in waveform graph. • Min/Max: Tap to define the maximum / minimum value. Once the value goes beyond the specified value, the system will alarm. Graph: Tap to view the parameters in waveform graphs.
  • Page 51 LAUNCH X-431 PRO5 User Manual • Value: Switches the current graph display mode to the Value display mode. • Customize: Tap , a pull-down list of the data stream items appears on the screen. Select / deselect the desired items, and then screen will display / remove the waveforms corresponding to these items immediately.
  • Page 52 LAUNCH X-431 PRO5 User Manual Report: Tap to save the current data in text format. All reports are saved in Report -> Health Reports. For details on report operations, please refer to Chapter 5.6. Record: Tap to start recording diagnostic data. Recorded live data can serve as valuable information to help you in troubleshooting of vehicle problems.
  • Page 53 LAUNCH X-431 PRO5 User Manual current standard range. Tap it to start recording the sample data (*Note: Only data stream items with measurement units will be recorded), the following screen will appear: Once the recording process is complete, tap to stop it and navigate to the data revision screen.
  • Page 54 LAUNCH X-431 PRO5 User Manual During the actuation test, the display tablet outputs commands to the ECU in order to drive the actuators, and then determines the integrity of the system or parts by reading the ECU data, or by monitoring the operation of the actuators, such as switching an injector between two operating states.

  • Page 55: Remote Diagnose

    LAUNCH X-431 PRO5 User Manual 5.3 Remote Diagnose This module helps repair shops or mechanics to diagnose a remote vehicle, and launch instant messages, allowing for improved efficiency and faster repairs. Tap Remote Diagnose on the Job menu, the screen appears blank by default.

  • Page 56: Add Friends

    LAUNCH X-431 PRO5 User Manual 5.3.1 Add Friends Tap Contacts. By default it appears blank. In the search bar, input the partner’s username and tap Search to start searching. The partner must be the users who have registered specific diagnostic tools.

  • Page 57: Start Instant Messaging

    LAUNCH X-431 PRO5 User Manual Tap Add friend to send your request. Once the partner receives the request, a beep will sound. Tap Messages: • Once the partner agreed your request, he/she will automatically be listed in the Contacts tab.

  • Page 58: Launch Remote Diagnosis (Device-To-Device)

    LAUNCH X-431 PRO5 User Manual Tap the input field and use the on-screen keyboard to send the text message. to send the voice message. to send the emoj. to call out more function options. File: Choose diagnostic reports or local files to send.
  • Page 59 LAUNCH X-431 PRO5 User Manual On the function option selection screen, tap Remote Diagnostic, the following pull-down menu will appear: These options are defined as follows: Actions Results Request to control the partner’s device remotely to help him diagnose the vehicle.
  • Page 60 LAUNCH X-431 PRO5 User Manual Notes:  In process of remote diagnosis, tap the button to send a voice message.  Once you received the report from the partner, tap View Report to view details. All diagnostic reports are saved under Report -> Remote Report.

  • Page 61: Launch Remote Diagnosis (Device-To-Pc)

    LAUNCH X-431 PRO5 User Manual 5.3.4 Launch Remote Diagnosis (Device-To-PC) User also can ask for remote control from a PC client technician. Tap Remote, the following screen will appear:...
  • Page 62 LAUNCH X-431 PRO5 User Manual 1. Slide the switch to ON so that the partner can find and connect to this device while using the PC. 2. Notify the partner of the PC client website http://remote.x431.com. When the partner accesses the link, the PC displays as below: Note: Before processing remote diagnosis, please make sure the tool is properly connected to the vehicle.

  • Page 63: Feedback

    LAUNCH X-431 PRO5 User Manual 4. Tell the partner to enter the Serial Number provided by you, and then tap Start remote diagnosis to control your device remotely. In process of remote diagnosis, please note the following things: 1) You are not suggested to execute any actions.

  • Page 64: Diagnostic History

    LAUNCH X-431 PRO5 User Manual Tap it to view the diagnostic feedback logs which are marked with different color indicating the process status of the diagnostic feedback. C. Offline list Tap it to enter the diagnostic feedback offline list page. Once the tablet gets a stable network signal, it will be uploaded to the remote server automatically.

  • Page 65: Service (Reset) Function

    LAUNCH X-431 PRO5 User Manual 6 Service (Reset) Function This module provides an easy dial to quickly access the most commonly performed service functions as follows.  Oil Reset Service  Electronic Parking Brake Reset  Steering Angle Calibration  ABS Bleeding ...

  • Page 66: Electronic Parking Brake Reset

    LAUNCH X-431 PRO5 User Manual 6.2 Electronic Parking Brake Reset This function enables you to reset the brake pad after replacing the brake pad. It needs to be performed in the following cases: 1. The brake pad and brake pad wear sensor are replaced.

  • Page 67: Immo Service

    LAUNCH X-431 PRO5 User Manual It needs to be performed in the following cases: 1. After the engine ECU, crankshaft position sensor, or crankshaft flywheel is replaced. 2. The DTC 'tooth not learned' is present. 6.7 IMMO Service This function enables you to perform the anti-theft key matching function, so that the immobilizer control system on the car identifies and authorizes remote control keys to normally use the car.

  • Page 68: Electronic Throttle Position Reset

    LAUNCH X-431 PRO5 User Manual It needs to be performed in the following cases: 1. The exhaust back pressure sensor is replaced. 2. The PM trap is removed or replaced. 3. The fuel additive nozzle is removed or replaced. 4. The catalytic oxidizer is removed or replaced.

  • Page 69: Immo Programming

    LAUNCH X-431 PRO5 User Manual 6.16 IMMO Programming This function enables you to perform read-write function for vehicle key, EEPROM, MCU, and EEPROM/FLASH data of vehicle engine/gearbox ECU.

  • Page 70: Software Update

    LAUNCH X-431 PRO5 User Manual 7 Software Update This module enables you to update the diagnostic software & App and frequently used software. 7.1 Update Diagnostic Software & APP Go to Software Update on the Job Menu and tap the Downloaded tab.

  • Page 71: Update Frequently Used Software

    LAUNCH X-431 PRO5 User Manual To download certain software that is not frequently used, check the box before the vehicle model. Tap Update to start downloading. Once download is finished, the software packages will be installed automatically. 7.2 Update Frequently Used software If the user only intends to update the frequently used software, go to Software Update and tap the Downloaded tab.
  • Page 72 LAUNCH X-431 PRO5 User Manual renew your subscription. Tap Renewal on the bottom of the screen to enter the payment screen. There are three ways available for you to make payment: PayPal, Subscription Renewal Card (*need to buy it from the local dealer where you purchased the tool) and Credit Card.
  • Page 73 LAUNCH X-431 PRO5 User Manual 2. Input the 24-digit pin code of Subscription Renewal Card and then tap Submit to finish the renewal. 3. Go to update center to update the diagnostic software. 3. Using Credit Card 1. Select Credit Card, and then follow the on-screen instructions to finish the transaction.

  • Page 74: Add-On Modules

    LAUNCH X-431 PRO5 User Manual 8 Add-on Modules 8.1 ADAS (Calibration) This module enables you to effectively and accurately calibrate a wide range of camera-based & radar-based driver assistance systems, e.g. the front camera for the lane departure warning system, the radar sensor for the ACC (Adaptive Cruise Control) or the camera for adaptive headlights.
  • Page 75 LAUNCH X-431 PRO5 User Manual For more details, please refer to the User Manual included with the module.

  • Page 76: User Info

    LAUNCH X-431 PRO5 User Manual 9 User Info This function allows users to manage personal information and VCI. 9.1 My Report This option is used to view, delete or share the saved reports. Tap Report, there are total 3 options available.

  • Page 77: Firmware Fix

    LAUNCH X-431 PRO5 User Manual Input the Serial Number and Activation Code, and then tap Activate to activate the VCI. 9.5 Firmware Fix Use this item to upgrade and fix diagnostic firmware. During fixing, please do not cut power or switch to other interfaces.

  • Page 78: Change Password

    LAUNCH X-431 PRO5 User Manual • Tap the user image to change it. • Tap > next to Upgrade Period to check the due date of all diagnostic software. 9.10 Change password This item allows you to modify your login password.

  • Page 79: Printer Set

    LAUNCH X-431 PRO5 User Manual 9.11.3 Printer Set This option is designed to establish a wireless connection between the tablet and the Wi-Fi printer (sold separately) while performing printing operations. The App is compatible with the LAUNCH Wi-Fi Printer (sold separately) and ®...
  • Page 80 LAUNCH X-431 PRO5 User Manual Tap Scan to select the desired local Wi-Fi network from the list, and type in the security password (If it is an open network, password is not required), and then tap Confirm. 3. Once the Wi-Fi network of the printer is connected and the printer is found, tap Printing test to test the printing.
  • Page 81 LAUNCH X-431 PRO5 User Manual 4. Touch next to Select a printer on the upper left corner of the screen. 5. Select All Printers -> Add printer and enable the installed printer service, the system starts searching for all available Wi-Fi printers of the brand.

  • Page 82: Orientation

    LAUNCH X-431 PRO5 User Manual 6. Select the desired Wi-Fi printer from the list. If the chosen Wi-Fi printer hotspot is open, the tablet can connect it directly. If it is encrypted, a password may be required. Refer to the Wi-Fi printer user manual to get the default password.
  • Page 83 LAUNCH X-431 PRO5 User Manual The newly added sub-account has a one-year validity period. After the expiration, the VCI bound to the sub-account cannot be used and the sub-account will no longer enjoy the rights and interests of the main account. The main account can modify the validity period of the sub-account.

  • Page 84: Login/Logout

    LAUNCH X-431 PRO5 User Manual • If you already have an account, please enter the user name and password. After inputting, tap Add Immediately to add it as a sub-account. • If you have not registered any account, tap Create sub user. Enter the user name and password, and then tap Add Immediately to add it as a sub-account.

  • Page 85: J2534 Programming

    LAUNCH X-431 PRO5 User Manual 10 J2534 Programming This chapter introduces how the VCI works with the PC installed with the OEM diagnostic software to perform the J2534 reprogramming. 10.1 Working principle Below illustrates the relationship between the various components required for...
  • Page 86 LAUNCH X-431 PRO5 User Manual 1. Connect B-shaped plug of the USB cable to the B-shaped USB port of the VCI device, and the other end to the USB port of the PC. 2. Use the OBD II extension cable to connect the VCI device to the vehicle's OBD II diagnostic socket.

  • Page 87: Install The Software & Driver

    LAUNCH X-431 PRO5 User Manual OBD II diagnostic socket. 10.3 Install the software & driver Note: Before installing the software, please make sure that the PC user is authorized with administrator rights and the SmartLink device has been properly connected to the PC.

  • Page 88: Faq

    4. If all checks are normal, send vehicle year, make, model and VIN number to us using Feedback feature. 4. How to download the X-431 PRO5 App after resetting the tablet? Note: Before registration, please make sure the network is properly connected.
  • Page 89 LAUNCH X-431 PRO5 User Manual and tap the Download icon to start downloading. 4. After the download is complete, follow the on-screen instructions to install it. 5. After installation, use the existing username and password to login and go to update center to download the diagnostic software.
  • Page 90 Warranty This warranty is expressly limited to persons who purchase LAUNCH products for purposes of resale or use in the ordinary course of the buyer’s business. LAUNCH electronic product is warranted against defects in materials and workmanship for one year (12 months) from date of delivery to the user. This warranty does not cover any part that has been abused, altered, used for a purpose other than for which it was intended, or used in a manner inconsistent with instructions regarding use.

Table of Contents