Table of Contents
Advertisement
Pre-Installation
Required Tools
Normal service tools are required to perform the majority
of the work. A service technician with a well stocked tool
chest should have the right tools to perform the job. In
addition to the normal service tools and hardware, the
following is a partial list of specific field supplied
hardware/software components and special tools that are
also required to perform the display retrofit:
•
RS-232 male DB9 to female DB9 pin to pin serial cable
to connect the DynaView™ to a PC or laptop computer
Note:
– The cable must NOT be a "null-modem" cable.
– The cable must be less than 50 feet in length.
•
Type A to Type B USB cable to connect the Tracer™
UC800 controller to a PC or laptop computer
•
A PC or laptop computer equipped with the following:
– KestrelView™ service software, version 14.0 or
newer
Parts
Table 2.
Components — close mount 460 volts
Kit Part Number
Mnemonic
RNG02318
BRD02944
HLD00579
RAL01142
127500010001
CAB01534
CAB01153
CAB01150
18
Part Number
Description
Close Mount Components
X13640734010
Choke Core M-116
531405110100
Core Support Bracket
531405470100
Buss Bar, Formed (for motor connection)
531405480100
Buss Bar, Straight (for motor connection)
X13650733060
Dual Relay output Ref 1A8 (latest revision)
X13260721020
Relay, 4PDT, 120VAC, 8amps
X13260722010
Relay Socket, 4PDT, Din rail mount
X13500224070
Din rail 4inch
X13491363010
Din Rail End Stop
507117910001
Strut Channel, 1.625"x 1.625"x 5ft (black color)
507117920001
Strut Channel Base, 4"X6" (black color)
507117930001
Strut Channel L Bracket
507117960001
.75in conduit connector 90 degree
507117970001
.75 IN CONDUIT CONNECTOR STRAIGHT
X19080029040
0.75in conduit - AFD/relay signal wires
X19010309470
single conductor cable - 16awg UL 1230 blk
X19051625030
Global harness Female to Amp connector 78.74in
X19051624030
Global harness Male to Amp connector 78.74in
X19051623020
Extension Harness - 78.74inch
X39002507010
Label, Warning (AFD)
507117810001
Label, Nameplate
AFDR-SVN001*-EN
KIT IOM (supplied by Trane)
507117830001
Schematics Printed on mylar
BAS-SVX54*-EN
Drive IOM
507118200001
AFD Label
X39003759010
Label, Technical support
507118300001
Motor Terminal Shield
– Tracer TU service software, version 9.0.322 or
newer
– RTHD UC800 firmware build 3.03 or later (refer to
"Preparing Tracer TU on the Service Computer,"
p.
26)
•
South pole magnet screwdriver (TOL01343)
•
Electronics vacuum
•
Drill
•
3/16-in. drill bit
•
3/8-in. drill bit for display arm
•
2.5-in hole saw (close mount kit only)
•
Phillips screwdriver
•
Wrench for fastening the bolts for the panel
•
Wire cutter for large and small gage wire
•
Vacuum pump
•
Oil pump
•
Impact drill for concrete
QTY
5
1
2
1
1
2
2
1
4
1
1
1
1
1
20 ft
125 ft
1
1
1
1
1
1
1
1
1
1
1
AFDR-SVN001D-EN
Advertisement
Table of Contents
