Summary of Contents for Renesas CPU Board M3A-HS19
Page 1
On April 1 , 2010, NEC Electronics Corporation merged with Renesas Technology Corporation, and Renesas Electronics Corporation took over all the business of both companies. Therefore, although the old company name remains in this document, it is a valid Renesas Electronics document. We appreciate your understanding.
Page 2
Renesas Electronics. Renesas Electronics shall not be in any way liable for any damages or losses incurred by you or third parties arising from the use of any Renesas Electronics product for an application categorized as “Specific”...
Page 3
SH7619 CPU Board M3A-HS19 User’s Manual Renesas 32-Bit RISC Microcomputers SuperH™ RISC engine Family/SH7619 Group Rev.1.01 2008.10...
Page 4
Please be sure to implement safety measures to guard against the possibility of physical injury, and injury or damage caused by fire in the event of the failure of a Renesas product, such as safety design for hardware and software including but not limited to redundancy, fire control and malfunction prevention, appropriate treatment for aging degradation or any other applicable measures.
Page 6
3.2.2 Features of Switches and LEDs ... 3-18 3.3 Dimensions... 3-20 Appendix...A-1 M3A-HS19 SCHEMATICS Rev. 1.01 Oct 28, 2008 REJ10J1351-0101 (ii)
1.1 Overview The M3A-HS19 is a CPU board designed to evaluate the feature and performance of the SH7619 Group of Renesas Technology original MCU, as well as developing and evaluating the application software for the MCUs. SH7619 data bus, address bus and on-chip peripheral pins are all connected to expansion connectors and appropriate connectors to allow for the timing evaluation with peripherals using measurement instruments, and the development of the optional boards according to its application.
1.5 M3A-HS19 Block Diagrams Figure 1.5.1 shows the system block diagram. H-UDI (14-pin) connector Bus switch PCMCIA connector Rev.1.01 Oct 28, 2008 REJ10J1351-0101 Serial port connector (RS-232C x 2, RS-422 x 1) 16-bit SCIF H-UDI /SCI GPIO/ Other EtherC SH7619 Peripheral Functions 16-bit...
1.6 M3A-HS19 Board Overview Figure 1.6.1 shows the M3A-HS19 board overview. Top view of the component side PCMCIA power control IC Power connector Power switching jumper AC adaptor jack U12, U16 3.3V/1.8V regulator IC Reset switch IRQ0 switch Top view of the solder side PC card connector (68-pin)
1.7 M3A-HS19 Memory Mapping Area 0 bus width: (Default) Data alignment: (SW4-1) Figure 1.7.1 show the memory mapping examples of the SH7619 on the M3A-HS19. Logical Address [31~29] 000~011 100~ 101~ 110~ 111~ Address [28~0] Area H'0000 0000 Area 0 64 MB H'0400 0000 Area 1...
1.8 Absolute Maximum Ratings Table 1.8.1 lists the absolute maximum ratings. Symbol Parameter 5 V system power supply voltage 3.3 V system power supply voltage 3VCC 1.8 V system power supply voltage 1.8VCC Operating temperature Topr Storage temperature Tstr Note: Temperature refers to the air temperature in the vicinity of the board. 1.9 Recommended Operating Conditions Table 1.9.1 lists the recommended operating conditions.
Page 16
Overview 1.8 Absolute Maximum Ratings This page intentionally left blank Rev.1.01 Oct 28, 2008 1-10 REJ10J1351-0101...
2.2 CPU 2.2.1 SH7619 The M3A-HS19 CPU board includes the SH7619, the 32-bit RISC MCU operates with a maximum frequency of 125 MHz. The SH7619 is equipped with an Ethernet controller that includes an IEEE802.3u compliant Media Access Controller and a Physical Layer Transceiver.
2.3 Memory The M3A-HS19 includes the SH7619 on-chip U memory, an external flash memory, external SDRAM and EEPROM. Details are described below (Except the PC card). 2.3.1 SH7619 U Memory and Cache Memory The SH7619 has a 16-KB (RAM) U memory module (address: H’E55FC000~H’E55FFFFF) and a 16-KB instruction/data-unified cache memory.
Page 21
Table 2.3.2 Setting Example of Bus State Controller (Flash Memory Write and Read) User Area Applicable Device S29GL032A90TFIR4 <Write/Read Timing> Write1 Tw 1 Tw 2 Tw 3 Tw 4 Tw 5 Taw 1 CKIO tAD1 A21-A1 tCSD1 CS0# tWED1 tWED1 WE0# tWDD1 tWDH1...
2.3.3 External Synchronous DRAM (SDRAM) The M3A-HS19 is provided with a 16-MB synchronous DRAM (SDRAM) as an external main memory. The SDRAM is controlled by the SH7619 on-chip bus state controller. The SDRAM is accessed in 16-bit bus. Table 2.3.3 lists SDRAM specifications used on the M3A-HS19, and Figure 2.3.3 shows its block diagram. Items Part Number EDS1216AATA-75E...
Page 23
A power-on sequence is required to use a SDRAM. Power-on sequence is to initialize the pin function controller (PFC), set registers in the bus state controller and write data in the SDRAM mode register. Table 2.3.4 lists the access address when writing in the SDRAM mode register on the CS3 space. Table 2.3.4 Access Address for SDRAM Mode Register Write (CS3 Space) Burst read/single write (burst length 1) Data bus...
Figure 2.3.4 shows a timing example of SDRAM mode register writing. CKIO SDRAM PALL DESL Command A11-A1(A9-A0) A12(A10/AP) CS3# RASL# CASL# RD/WR# DQMUU-LL (High) Hi-Z D15-0 [Symbols Descriptions] PALL : All bank precharge command REF : Auto-refreshing command MRS : Mode register write commamd DESL : Deselect command Figure 2.3.4 Timing Example of SDRAM Mode Register Writing Rev.1.01 Oct 28, .2008...
Page 25
Table2.3.5 lists setting examples of the bus state controller with SH7619 bus clock at 62.5 MHz. Figure 2.3.5 shows the SDRAM single read/write timing example. Table2.3.5 Setting Example of Bus State Controller (SDRAM Read/Write) User Area Applicable Device EDS1216AATA-75E Rev.1.01 Oct 28, .2008 REJ10J1351-0101 Settings for Bus State Controller CS3 Space Bus Control Register: CS3BCR...
Page 26
SDRAM SINGLE READ tRAS tRAS AC T READ A Trw1 CKIO tCSD1 CS3# tRASD1 tRASD1 RAS# CAS# RD/WR# tDQMD1 DQMUU-LL tAD1 tAD1 A11-A1(A9-A0) tAD1 tAD1 A12(A10/AP) tAD1 tAD1 A14,A13(BA1,0) D15-0 Rev.1.01 Oct 28, .2008 REJ10J1351-0101 tCSD1 tCASD1 tCASD1 tDQMD1 tAD1 tAD1 tAD1 tAD1...
2.3.4 External EEPROM The M3A-HS19 is provided with an EEPROM for storing MAC address. Access to the EEPROM is enabled by using the SH7261 I/O ports (PC03, PC02, PC01 and PC00). A MAC address consists of 48-bit numbers. Table 2.3.6 lists instruction sets, and Figure 2.3.6 shows the block diagram of CPU and EEPROM connection. Figure 2.3.7 shows the EEPROM-AC timing and Figure 2.3.8 shows EEPROM-read/write timing.
Page 28
AC characteristics Hi-Z READ Dummy SK "x" A "0" "1" "1" "1" "0" Hi-Z WRITE Dummy SK Writing Instruction, Address, Writing Data Input "0" "1" "0" "1" "x" Hi-Z Rev.1.01 Oct 28, .2008 REJ10J1351-0101 Clock pulse width 1 μsec or more 1 μsec or more Writing Enabled Data...
2.4 Serial Port Interface The SH7619 MCU mounted on the M3A-HS19 is provided with a 3 channel’s of the Serial Communication Interface with FIFO (SCIF). SCIF channel 0 is connected to the 2-pin serial port connector, SCIF channel 2 is connected to the D-sub 9-pin serial port connector, and SCIF channel 1 is connected to the 4-pin serial port connector.
2.5 PCMCIA Card Interface The SH7619 MCU mounted on the M3A-HS19 is compliant with the JEIDA 4.2 (PCMCIA2.1 Rev.2.1). However, only 3.3 V interface PC card is supported. An on-chip bus state controller (BSC) and a PFC control the PC card. High byte and low byte of the data is switched at the bus switch on the M3A-HS19.
2.6 LAN Port Interface An IEEE 802.3 compliant (MAC layer) Ethernet controller and an IEEE802.3/802.3u compliant (10/100 Mbps Ethernet PHY) physical layer transceiver are embedded in the SH7619 MCU. Figure 2.6.1 shows the block diagram of LAN port interface. SH7619 (U1) (MII) MII-compliant signal Rev.1.01 Oct 28, .2008...
2.7 I/O Port Following I/O ports on the M3A-HS19 can be configured by the SH7619 MCU. These ports are multiplexed pins with up to four features. Some pins have several initial features for normal mode and HIF (Host Interface) boot mode. Features can be controlled by PFC (pin function controller).
2.8 Power Supply Circuit The main power supply input 5 V DC to the M3A-HS19 and it generates 3.3 V and 1.8 V using a regulator. It is an adjustable output voltage regulator to generate a desired voltage by changing resistance values. A through-hole is provided with the M3A-HS19 to input 1.8 V DC from an external power supply.
2.9 Clock Module The clock module on the M3A-HS19 consists of following three blocks; • A block connecting X1 (oscillator) output to SH7619 EXTAL • A block connecting X2 (ceramic resonator) to EXTAL and XTAL (Optional) • A block connecting X3 (oscillator) to CK-PHY An on-chip oscillator (15.625 MHz) is connected to the SH7619 MCU to provide an operating clock.
2.10 Reset Module Reset module controls reset signals connected to the SH7619 MCU, a flash memory and connectors. Software controls to reset PCMCIA connector. Figure 2.10.1 shows the schematic diagram of resets. Reset IC output delay time: td = 0.34×Cd(pF)µsec = 34 ms Reset IC output detect voltage: Vs = 1.25×...
2.11 Interrupt Switch Push-button switches are connected to the SH7619 NMI pin and IRQ0 pin. Interrupts are connected to IRQ7 from an expansion connector and a PCMCIA connector. Figure 2.11.1 shows the schematic diagram of interrupts. SW 5 NMI switch SW 6 IRQ0 switch IREQ#...
2.12 E10A-USB Interface The M3A-HS19 is provided with a 14-pin H-UDI connector to embed the E10A-USB emulator. Figure 2.12.1 shows the block diagram of the E10A-USB interface. H-UDI connector (J6) UVCC TRST# (GND) RES# Reset Rev.1.01 Oct 28, .2008 REJ10J1351-0101 3.3 V 3.3 V Figure 2.12.1 E10A-USB Interface...
Page 40
Features and Specifications 2.12 E10A-USB Interface This page intentionally left blank. Rev.1.01 Oct 28, .2008 2-24 REJ10J1351-0101...
3.1 M3A-HS19 Connectors Figure 3.1.1 shows the connector assignments on the M3A-HS19. Top view of the component side Power supply connector AC adapter jack GND pin for test 1.8 V External power supply connector (optional) RS-422 serial connector (optional) Top view of the solder side PC card connector J10, J12...
3.1.1 UART Connector Pin (J1) The M3A-HS19 is provided with an UART connector pin (J1). Figure 3.1.2 shows the pin assignment for the UART connector (J1). Figure 3.1.2 Pin assignment for UART Connector (J1) Table 3.1.1 lists the pin assignment for the UART connector (J1). Table 3.1.1 Pin assignment for UART Connector (J1) Pin no.
3.1.2 UART Connector (J2) The M3A-HS19 is provided with an UART connector (J2). Figure 3.1.3 shows the pin assignment for the UART connector (J2). Board edge Board edge Figure 3.1.3 Pin assignment for UART Connector (J2) Table 3.1.2 lists the pin assignment for the UART connector (J2). Table 3.1.2 Pin assignment for UART Connector (J2) Pin no.
Operational Specifications 3.1.4 PCMCIA Connector (J4) 3.1.4 PCMCIA Connector (J4) The M3A-HS19 is provided with a PCMCIA connector (J4). Figure 3.1.5 shows the pin assignment for the PCMCIA connector (J4). Top view of the solder side 3.3V PCMCIA ONLY Board Edge Figure 3.1.5 Pin assignment for PCMCIA Connector (J4) Rev.1.01 Oct.28.2008 REJ10J1351-0101...
Page 47
Table 3.1.4 lists the pin assignment for the PCMCIA connector (J4). Table 3.1.4 Pin assignment for PCMCIA Connector (J4) Pin no. Signal Name CE1# (CE2A#) OE# (RD#) WE# (WE1#/DQMLU/WE#) IREQ# (PD7/IRQ7/SCK2) VPP1 IOIS16# (PB01/IOIS16#) Rev.1.01 Oct.28.2008 REJ10J1351-0101 Operational Specifications 3.1.4 PCMCIA Connector (J4) Pin no.
3.1.5 LAN Connector (J5) The M3A-HS19 is provided with a LAN connector (J5). Figure 3.1.6 shows the pin assignment for the LAN connector (J5). Top view of the component side Board Edge Figure 3.1.6 Pin assignment for LAN Connector (J5) Table 3.1.5 lists the pin assignment for the LAN connector (J5).
3.1.6 H-UDI Connector (J6) The M3A-HS19 is provided with an H-UDI (J6) connector to connect the E10A-USB emulator. Figure 3.1.7 shows the pin assignment for the H-UDI connector (J6). Figure 3.1.7 Pin assignment for H-UDI Connector (J6) Table 3.1.6 lists the pin assignment for the H-UDI connector (J6). Table 3.1.6 Pin assignment for H-UDI Connector (J6) Pin no.
3.1.7 Power Supply Connector (J7) The M3A-HS19 is provided with a connector for power supply. Figure 3.1.8 shows the pin assignment for the power supply connector (J7). Board Edge Board Edge Figure 3.1.8 Pin assignment for Power Supply Connector (J7) Table 3.1.7 lists the pin assignment for the power supply connector (J7).
3.1.8 External Power Supply Connector (J8) The M3A-HS19 is provided with a through-hole for the SH7619 external power supply connector (J8: Supplies 1.8 V). Figure 3.1.9 shows the pin assignment for the external power supply connector (J8). Top view of the component side Figure 3.1.9 Pin assignment for External Power Supply Connector (J8) Table 3.1.8 lists the pin assignment for the external power supply connector (J8).
3.1.9 Expansion Connectors (J9-J13) The M3A-HS19 is provided with through-holes for expansion connectors. The Through-holes are connected to the SH7619 I/O pins. Expansion connectors (J9 - J13) can be connected to the MIL STD connector to mount expansion boards or to monitor the SH7619 bus signals. Figure 3.1.10 shows the pin assignment for expansion connectors.
Page 53
Table 3.1.10 Pin assignment for Expansion Connector (J10) Pin no. Signal Name +3.3 V PA22/A22/SIOMCLK0, PD4/IRQ4/SCK1 Jumper select PA21/A21/SCK_SIO0 PA19/A19 PA17/A17 PC13/TX_CLK PC12/TX_EN PB11/CS4# PC08/RX_DV RES# Table 3.1.11 Pin assignment for Expansion Connector (J13) Pin no. Signal Name PE24/HIFD15/CTS1/D31 PE22/HIFD13/CTS0/D29 PE20/HIFD11/SCK1/D27 PE18/HIFD09/TXD1/D25 PE16/HIFD07/RXD0/D23...
Page 54
Table 3.1.12 Pin assignment for Expansion Connector (J12) Pin no. Signal Name +5 V DD14 DD12 DD10 Table 3.1.13 Pin assignment for Expansion Connector (J11) Pin no. Signal Name PD0/IRQ0/-/TEND0 PB12/CS3# WE0#/DQMLL , PE06/HIFWR#/SIOFSYNC0 Jumper select PB05/WE2#(BE2)/DQMUL/ICIORD# PE00/HIFEBL/SCK_SIO0 PC11/TX_ER PC10/RX_CLK Rev.1.01 Oct.28.2008 REJ10J1351-0101 Operational Specifications...
3.2 Switches and LEDs The M3A-HS19 is provided with switches and LEDs as its operational components. Figure 3.2.1 shows the assignment of operational components. Top view of the component side Power switching jumper IRQ0 switch switch Reset switch Figure 3.2.1 M3A-HS19 Operational Components Assignment Rev.1.01 Oct.28.2008 REJ10J1351-0101 Power switch...
3.2.2 Features of Switches and LEDs The M3A-HS19 is provided with six switches and five LEDs. Figure 3.2.3 shows the pin assignment for switches and LEDs. Table 3.2.7 lists the switches mounted on the M3A-HS19. Top view of the component side IRQ0 switch Figure 3.2.3 Pin assignment for Switches and LEDs...
Page 59
Table 3.2.8 lists the SW4 features. Setting SW4-1 SW4-2 HIFEBL SW4-3 HIFMD SW4-4 FLASH_WP# Table 3.2.9 lists the LEDs on the M3A-HS19. Color LED1 Yellow User LED (LED1 lights when PC04/SPEED100# outputs "L") LED2 Yellow User LED (LED2 lights when PC05/LINK# outputs "L") LED3 Yellow User LED (LED3 lights when PC06/MII_TXD2/-/CRS# outputs "L")
3.3 Dimensions Figure 3.3.1 shows the M3A-HS19 dimensions. Connectors can be mounted on J9 through J13 to simplify to mount an expansion board. <Top view of the component side> <Transparent view of the component side> Rev.1.01 Oct.28.2008 REJ10J1351-0101 Figure 3.3.1 M3A-HS19 Dimensions Operational Specifications 3.3 Dimensions 3-20...
Page 71
Revision History Rev. Date Page 1.00 Aug 28, 2008 1.01 Oct 28, 2008 SH7619 CPU Board M3A-HS19User's Manual Description Summary First edition issued. Errors corrected.