Page 2
Renesas Technology or Renesas Technology Sales or other distributors. • This manual may not be copied or reproduced, in whole or part, without prior written consent of Renesas Technology. •...
Page 3
Revision History SH7206 CPU Board M3A-HS60User's Manual Rev. Date of Issue Content of Revision Page Points 1.00 June 1.2005 First edition issued.
1.1 Overview The M3A-HS60 is the CPU board designed for users to evaluate the function and performance of original microcomputers of Renesas Technology the SH7206 series. With the board, you can develop and evaluate the application software for the SH7206 series. The SH7206's data bus, address bus, and pins of various internal peripheral circuit function are connected to the extension bus connector of the M3A-HS60.
1.5 M3A-HS60 Block Diagram Figure1.5.1 shows the system block diagram of M3A-HS60. Flash memory SH7206 CPU Board M3A-HS60 Rev.1.00 June 1,2005 REJ11J0002-0100Z Serial port H-UDI connector SH7206 200MHz 16 or 32 External:66.67MHz Extension connector Enables to connect extension boards, or enables to monitor all of bus and peripheral I/O signals.
1.6 M3A-HS60 Board Overview Figure1.6.1 shows the M3A-HS60 board overview. Top view of the LED6-8 Component side User LED LED2-5 User Reset Switch Switch Top view of the Solder side 3.3V Power Regulator 1.25V Power Regulator :Extension connector(not mounted) Rev.1.00 June 1,2005...
Page 11
Table1.6.1 lists main components mounted in M3A-HS60. Table1.6.1 Main Components Mounted in M3A-HS60 Symbol Component name Clock Buffer Flash Memory U4,U7 Address Shift Buffer U5,U8 SDRAM Logic IC RS-232C Driver 3.3V Power Regulator Reset IC 1.25V Power Regulator 16.67MHz Oscillator...
Storage Ambient Temperature Note: The ambient temperature refers to the air temperature in the closest place from the board. 1.9 Recommended Operating Conditions Table1.9.1 lists the recommended operating conditions of the M3A-HS60. Table1.9.1 Recommended Operating Conditions of M3A-HS60 Symbol Parameter...
Page 14
Overview 1.8 Absolute Maximum Ratings This is a blank page Rev.1.00 June 1,2005 1-10 REJ11J0002-0100Z...
• Data bus width fixed to 16 bits Connects SCIF0 of the SH7206 to the Serial port connector. Connects to the I/O ports of the SH7206 Controls the system power supply of the M3A-HS60 Controls the clock Controls device reset mounted on the M3A-HS60...
The SH7206 includes 128-Kbyte RAM, 8-Kbyte instruction cache and 8-Kbyte data cache, and it can deal with a wide range of applications from data processing to equipment control. The M3A-HS60 can be operated with a maximum 200MHz of CPU clock frequency (external bus 66.67MHz, max.) using a 16.67MHz input clock.
2.3.2 Flash Memory M5M29KT331AVP (included as standard equipment) The M3A-HS60 includes the Flash memory shown in Table2.3.1 as standard equipment. The memory can be used as the storage in which to save the user program. The Flash memory to boot is fixed to 16-bit mode of external bus and operates with a single 3.3 V power supply voltage.
Page 19
Table2.3.2 Examples for Bus State Controller Settings (Flash Memory Write/Read) User Area Applicable Device M5M29KT331AVP <Write and Read Timing> Write1 Tw1 Tw2 CKIO tAD1 A21-A1 tCSD1 CS0# tWED1 WE0# tWDD1 D15-D0 DATA Figure2.3.2 Flash Memory Read and Write Access Timing Rev.1.00 June 1,2005 REJ11J0002-0100Z 2.3.2 Flash Memory M5M29KT331AVP (included as standard equipment)
2.3.3 External SDRAM The M3A-HS60 includes two pcs. of 16-Mbyte SDRAM (for an external SDRAM) as standard equipment. The SH7206's internal bus state controller can be used to control the SDRAM. Note that the SDRAM can be switched between 32-bit bus access and 16-bit bus access. (For 16-bit bus access, only one pc.
Page 21
Table2.3.4 lists bus state controller settings for operation with the SH7206 Bus clock at 66.67MHz. Table2.3.4 Examples for Bus State Controller Settings (SDRAM Read/ Write) User Area Application Device EDS1216AATA-75E Rev.1.00 June 1,2005 REJ11J0002-0100Z Bus State Controller Settings CS3 Space Bus Control Register (CS3BCR) Initial value: H'36DB 0600 Recommended set value: H'0000 4400 (for 16-bit bus) or H'0000 4600 (for 32-bit bus)
Page 22
Trw1 Trw2 CKIO tCSD1 CS3# tRASD1 tRASD1 RASL# CASL# RD/WR# tDQMD1 DQMUU-LL tAD1 A11-A2(A9-A0) tAD1 A12(A10/AP) tAD1 A15,A14(BA1,0) D0-31 Figure2.3.4 Typical SDRAM Single Read/Write Timing Rev.1.00 June 1,2005 REJ11J0002-0100Z SDRAM SINGLE READ tRAS tRAS READA tCSD1 tCSD1 tRASD1 tCASD1 tCASD1 tDQMD1 tDQMD1 tAD1...
2.4 Serial Port Interface The SH7206 included in the M3A-HS60 contains a UART module. As for the M3A-HS60, SCIF channel 0 is connected to serial port connector. Figure2.4.1 shows a block diagram of serial port interface in the M3A-HS60. SH7206...
As for the M3A-HS60, the SH7206's I/O ports are connected to the extension bus connector of the M3A-HS60 board. Some I/O ports are connected to DIP switches and LEDs of the M3A-HS60 board. Users are free to use these ports.
Page 25
PE14 PE15 PF0-7 Rev.1.00 June 1,2005 REJ11J0002-0100Z Table2.5.1 Functions of SH7206 I/O Ports Connection in the M3A-HS60 Serial port connector. Extension connector, SDRAM_SZ signal input. Extension connector. Flash memory and extension connector. SDRAM and extension connector. Flash memory, SDRAM and extension connector.
2.6 Power Supply Circuit The M3A-HS60 accepts a 5V power supply as its input, and generates 3.3V and 1.25V by using a regulator. The regulator used here is an output voltage variable type, so that any desired voltage can be generated by changing the resistance value.
• Ceramic resonator connected to EXTAL and XTAL The M3A-HS60 has a 16.67MHz oscillator connected. Furthermore, the bus clock output from the SH7206 is connected to the SDRAM via a damping resistor. To connect an extension board to the extension connector, we recommend including a clock buffer that contains a PLL to ensure that the board will be supplied with a stable clock signal.
2.9 Interrupt Switches As for the M3A-HS60, both the SH7206's NMI interrupt pin and MRES pin have a push switch connected. MRES switch can be used for controlling manual reset for SH7206. When manual reset is done, the internal condition of CPU will be formatted, but each register of on-chip peripheral module.
2.10 E10A-USB Interface As for the M3A-HS60, a 36-pin H-UDI connector to connect it with the E10A-USB is mounted. Figure2.10.1 shows a block diagram of the E10A-USB interface. H-UDI connector (36-pin type) AUDCK AUDATA0 AUDATA1 AUDATA2 AUDATA3 AUDSYNC# N.C. N.C. 15...
Page 30
Functional Overview 2.10 E10A-USB This is a blank page Rev.1.00 June 1,2005 2-16 REJ11J0002-0100Z...
3.1.1 H-UDI Connector (J1) The M3A-HS60 includes an H-UDI (J1) connector for connection to the E10A-USB emulator. Figure3.1.2 shows a pin arrangement of the H-UDI connector. Board edge Board edge Figure3.1.2 Pin Arrangements of the H-UDI Connector Table3.1.1 lists pin assignments of H-UDI connector.
3.1.2 Serial Port Connector (J2) The M3A-HS60 includes a serial port connector for serial communication (J2). Figure3.1.3 shows a pin assignment of serial port connector. Board edge Board edge Figure3.1.3 Pin Arrangement of Serial Port Connector (J2) Table3.1.2 lists pin assignments of serial port connector.
3.1.3 External Power Supply Connectors(J3 and J5) The M3A-HS60 has the through-hole for two external power supply connectors (J3 for 3.3 V and J5 for 1.25 V) for the SH7206. Figure3.1.4 shows a pin assignment of external power supply connectors.
3.1.4 Power Supply Connector (J4) The M3A-HS60 includes a power supply connector for the board itself. Figure3.1.5 shows a pin assignment of power supply connector. Board edge Board edge Figure3.1.5 Pin Arrangement of Power Supply Connector (J4) Table3.1.5 lists pin assignments of power supply connector for the M3A-HS60.
The through-hole for the extension connector pin connecting the pins of the on-chip peripheral functions (such as MTU2 and AD), which is suitable for the motor control of SH7206, is mounted on M3A-HS60. Figure3.1.6 shows a pin arrangement of extension connector.
Page 38
Table3.1.7 Pin Assignments of Extension Connectors (J7 and J8) Signal Name D16/IRQ0/POE4#/AUDATA0/PD16 D17/IRQ1/POE5#/AUDATA1/PD17 D18/IRQ2/POE6#/AUDATA2/PD18 Rev.1.00 June 1,2005 REJ11J0002-0100Z Operational Specifications 3.1.5 User I/O Connectors (J6-J8) Signal Name AN5/PF5 AN6/DA0/PF6 AN7/DA1/PF7...
3.1.6 Extension Connectors (J9-J13) The M3A-HS60 has the trough-hole for extension bus connectors to which the I/O pins of the SH7206 are connected. MIL Standard connectors can be mounted to J9–J13, and it is available for the connection to extension boards, or monitoring the SH7206 bus signals.
Page 40
Table 3.1.8 to 3.1.12 list pin assignments of extension connector. Table3.1.8 Pin Assignment of Extension connector(J9) Signal name EXCLK A0/PC0 CS1#/POE5/PA11 RASU#/PINT4/CS4#/PA20 RESET# Table3.1.9 Pin Assignment of Extension connector(J10) Signal name +3.3V WDTOVF# A24/RXD1/PA3 A22/DREQ1/IRQ1/SCK1/PA5 EXCLK A0/PC0 CS1#/POE5/PA11 RASU#/PINT4/CS4#/PA20 RESET# Rev.1.00 June 1,2005 REJ11J0002-0100Z Operational Specifications...
Page 41
Table3.1.10 Pin Assignments of Extension Connector(J13) Signal Name D14/TIOC4CS/PD14 D12/TIOC4AS/PD12 D10/TIOC3CS/PD10 D8/TIOC3AS/PD8 Table3.1.11 Pin Assignments of Extension Connector (J12) Signal Name WAIT#/DACK2/PA17 D30/TIOC3CS/IRQOUT#/PD30 D28/CS2#/TIOC3DS/PD28 D26/DACK0/TIOC4BS/PD26 D24/DREQ0/TIOC4DS/PD24 D22/IRQ6/TIC5US/AUDCK/PD22 D20/IRQ4/TIC5WS/PD20 D18/IRQ2/POE6#/AUDATA2/PD18 D16/IRQ0/POE4#/AUDATA0/PD16 TEND0/TIOC0B/PE1 D14/TIOC4CS/PD14 D12/TIOC4AS/PD12 D10/TIOC3CS/PD10 D8/TIOC3AS/PD8 Rev.1.00 June 1,2005 REJ11J0002-0100Z Operational Specifications 3.1.5 User I/O Connectors (J6-J8) Signal Name D15/TIOC4DS/PD15...
Page 42
Table3.1.12 Signal Name IRQ1/POE1#/SDA/PB3 CS3#/TCLKB/PA7 WE0#/DQMLL#/POE6#/PA12 WE2#/ICIORD#/DQMUL#/TIC5V/PA22 FRAME#/CKE/TCLKD/IRQ3/PA9 CASL#/IRQ3/POE3#/PB5 SCK2/TIOC3A/PE8 BS#/RXD2/TIOC2B/UBCTRG#/PE7 CE2B#/DACK3/PINT7/POE8#/PA25 BACK#/TEND1/PINT3/PA19 Rev.1.00 June 1,2005 REJ11J0002-0100Z Pin Assignment of Extension connector (J11) IRQ0/POE0#/SCL/PB2 RD_WR#/IRQ2/TCLKC/PA8 WE1#/WE#/DQMLU#/POE7#/PA13 WE3#/ICIOWR#/AH#/DQMUU#/TIC5W/PA23 RASL#/IRQ2/POE2#/PB4 CS8#/PE16 TXD2/TIOC3C/PE10 CE2A#/DREQ3/PINT6/PA24 BREQ#/TEND0/PINT2/PA18 Operational Specifications 3.1.5 User I/O Connectors (J6-J8) Signal Name 3-12...
3.2 Outline of Switches and LEDs The M3A-HS60 includes switches and LEDs as its operational components. Figure3.2.1 shows the M3A-HS60 Operational Component Assignment. <Top view of the component side> Figure3.2.1 M3A-HS60 Operational Component Assignment Rev.1.00 June 1,2005 REJ11J0002-0100Z 3.2 Outline of Switches and LEDs...
Jumper Setting JP2. 1.2V PWRSEL Note: Do not change jumper settings while the M3A-HS60 is being operated. Be sure to turn off the power of the M3A-HS60 before changing jumper settings for all the time. Rev.1.00 June 1,2005 REJ11J0002-0100Z 3.2.1 Power Supply Select Jumpers (JP1 and JP2) Board edge 1.2V...
3.2.2 Switch and LED Functions The M3A-HS60 includes six switches and eight LEDs. Figure3.2.3 shows the M3A-HS60 Switch and LED Pin Assignment. Table3.2.3 lists the switches mounted on M3A-HS60. LED6 PE11 PE14 LED7 PE15 LED8 LED2 LED3 LED4 PE10 LED5 1 2 3 4 Figure3.2.3 M3A-HS60 Switch and LED Pin Assignment...
Page 46
SW4-5 FLASH _WP# When using the J6 connector, make sure the SDRAM bus width is set to 16-bit access (SW4-1 OFF). Table3.2.5 lists the functions of the LEDs mounted in M3A-HS60. Table3.2.5 Functions of the LEDs Mounted in M3A-HS60 Color LED1 Power-on LED (LED1 lights when 3.3 V power is supplied)
3.3 Outline Dimensions of M3A-HS60 Figure3.3.1 shows the outline dimensions of M3A-HS60. Connectors can be mounted on J6-J13 so that it is easy to connect extension boards. <Top view of the component side> <Perspective view of the component side> Rev.1.00 June 1,2005 REJ11J0002-0100Z Figure3.3.1 Outline Dimensions of M3A-HS60...
Page 48
Operational Specifications 3.3 Outline Dimensions of M3A-HS60 This is a blank page Rev.1.00 June 1,2005 3-18 REJ11J0002-0100Z...