Vertiv NetSure 211 Series Installation And User Manual
-48 vdc battery cabinet
Hide thumbs
Also See for NetSure 211 Series:
- Installation and user manual (28 pages) ,
- Installation and user manual (18 pages)
Related Manuals for Vertiv NetSure 211 Series
Summary of Contents for Vertiv NetSure 211 Series
- Page 1 NetSure™ 211 SERIES -48 VDC Battery Cabinet Installation and User Manual (Section 6033), Revision M Specification Number: 545534 Model Number: 211...
- Page 2 If you encounter any installation or operational issues with your product, check the pertinent section of this manual to see if the issue can be resolved by following outlined procedures. Visit https://www.vertiv.com/en-us/support/ for additional assistance. Vertiv™ NetSure™ 211 SERIES -48 VDC Battery Cabinet Installation & User Manual (Section 6033) | Rev. M...
-
Page 3: Table Of Contents
Installing Dynasty TEL12-30 Batteries ................... 19 Securing the Batteries Using the Battery Retention Strap........21 Typical Internal Wiring Layout ......................22 Operation ........................23 Vertiv™ NetSure™ 211 SERIES -48 VDC Battery Cabinet Installation & User Manual (Section 6033) | Rev. M... -
Page 4: Admonishments Used In This Document
SAFETY! Informs the reader of general safety information, reminders, precautions, or policies not related to a particular source of hazard or to fire safety. (ISO, ANSI, OSHA) Vertiv™ NetSure™ 211 SERIES -48 VDC Battery Cabinet Installation & User Manual (Section 6033) | Rev. M... -
Page 5: Important Safety Instructions
Even a momentary short circuit can cause sparking, explosion, and injury. Vertiv™ NetSure™ 211 SERIES -48 VDC Battery Cabinet Installation & User Manual (Section 6033) | Rev. M... -
Page 6: Battery
• Do not open or mutilate batteries. • ALWAYS FOLLOW THE BATTERY MANUFACTURER’S RECOMMENDATIONS AND SAFETY INSTRUCTIONS. Vertiv™ NetSure™ 211 SERIES -48 VDC Battery Cabinet Installation & User Manual (Section 6033) | Rev. M... -
Page 7: Personal Protective Equipment (Ppe)
Permits as required by the local authority, per NFPA 70E “Standard for Electrical Safety in the Workplace”. Hazardous Voltage DANGER! HAZARD OF ELECTRICAL SHOCK. More than one disconnect may be required to de-energize the system before servicing. Vertiv™ NetSure™ 211 SERIES -48 VDC Battery Cabinet Installation & User Manual (Section 6033) | Rev. M... - Page 8 This page is intentionally blank. Vertiv™ NetSure™ 211 SERIES -48 VDC Battery Cabinet Installation & User Manual (Section 6033) | Rev. M...
-
Page 9: Introduction
(8 Hr Rate) Enersys SBSB10 140553 38.0 28.2 C&D / Dynasty TEL12-30 140455 30.5 26.7 Enersys SBS30 26.0 20.9 Enersys SBS40 140581 38.0 28.0 Vertiv™ NetSure™ 211 SERIES -48 VDC Battery Cabinet Installation & User Manual (Section 6033) | Rev. M... -
Page 10: Specifications
Mounting the Battery Cabinet The battery cabinet is designed to mount in a standard 19” or 23” wide relay rack or on a wall. Vertiv™ NetSure™ 211 SERIES -48 VDC Battery Cabinet Installation & User Manual (Section 6033) | Rev. M... -
Page 11: Relay Rack Mounting
Refer to Figure 4. Install battery retention strap through openings in rear of battery cabinet. Orient the buckle per Figure Vertiv™ NetSure™ 211 SERIES -48 VDC Battery Cabinet Installation & User Manual (Section 6033) | Rev. M... - Page 12 Ensure the technique and hardware used in securing the cabinet can support the total weight of the cabinet and the batteries. Refer to “Batteries” on page 9 for a battery weight reference table. Vertiv™ NetSure™ 211 SERIES -48 VDC Battery Cabinet Installation & User Manual (Section 6033) | Rev. M...
-
Page 13: Connecting Battery Cabinet(S) To The Associated Power System
Connect the second battery cabinet’s battery cable terminated in an Anderson connector to the fixed mating Anderson connector located on the first battery cabinet. Repeat the above step if there are additional battery cabinets. Vertiv™ NetSure™ 211 SERIES -48 VDC Battery Cabinet Installation & User Manual (Section 6033) | Rev. M... - Page 14 P/N 565513. P/N 545696 is always used. P/N 565513 is used only with power systems containing a 1M831ANA Mini Controller (may be discarded if battery cabinet is used with other systems). Vertiv™ NetSure™ 211 SERIES -48 VDC Battery Cabinet Installation & User Manual (Section 6033) | Rev. M...
-
Page 15: Installing Enersys Sbsb10 Batteries
Figure 8: Installing Enersys SBSB10 Batteries Enersys SBS-B10 Batteries Slide Out Tray Spacers (P/N 545511) Vertiv™ NetSure™ 211 SERIES -48 VDC Battery Cabinet Installation & User Manual (Section 6033) | Rev. M... - Page 16 Connecting Enersys SBSB10 Batteries to (+) and (-) Terminals Anderson Connector Circuit Breaker To Anderson Connector [Positive (+) Cable] Enersys SBS-B10 Batteries To Circuit Breaker [Negative (-) Cable] Slide Out Tray Vertiv™ NetSure™ 211 SERIES -48 VDC Battery Cabinet Installation & User Manual (Section 6033) | Rev. M...
-
Page 17: Installing Enersys Sbs-30 Or Sbs-40 Batteries
Figure 11: Installing Enersys SBS-30 or SBS-40 Batteries Enersys SBS-30 or SBS-40 Batteries Slide Out Tray Spacers (P/N 545511) Vertiv™ NetSure™ 211 SERIES -48 VDC Battery Cabinet Installation & User Manual (Section 6033) | Rev. M... - Page 18 Connector To Anderson Connector [Positive (+) Cable] Circuit Breaker To Circuit Breaker [Negative (-) Cable] Enersys SBS-30 or SBS-40 Batteries Slide Out Tray Vertiv™ NetSure™ 211 SERIES -48 VDC Battery Cabinet Installation & User Manual (Section 6033) | Rev. M...
-
Page 19: Installing Dynasty Tel12-30 Batteries
Figure 14: Installing Dynasty TEL12-30 Batteries Spacer (P/N 545538) Spacers (qty. 2) Dynasty (P/N 545511) TEL12-30 Batteries Slide Out Tray Vertiv™ NetSure™ 211 SERIES -48 VDC Battery Cabinet Installation & User Manual (Section 6033) | Rev. M... - Page 20 Connecting Dynasty TEL12-30 Batteries to (+) and (-) Terminals Anderson Connector Circuit Breaker To Circuit Breaker [Negative (-) Cable] To Anderson Connector [Positive (+) Cable] Dynasty TEL12-30 Batteries Slide Out Tray Vertiv™ NetSure™ 211 SERIES -48 VDC Battery Cabinet Installation & User Manual (Section 6033) | Rev. M...
-
Page 21: Securing The Batteries Using The Battery Retention Strap
Looping the Strap into the Buckle Pull again the strap to tighten. Rotate buckle cover to closed position to apply and lock in tension. See Figure 19. Vertiv™ NetSure™ 211 SERIES -48 VDC Battery Cabinet Installation & User Manual (Section 6033) | Rev. M... -
Page 22: Typical Internal Wiring Layout
OUTPUT TO POWER SHELF OR OTHER BATTERY CABINET BATT BATT BATT BATT 49.9 ohm TO SUPPLEMENTAL TO -48V RESISTIVE BATTERY BATTERY CABINET BREAKER ALARM Vertiv™ NetSure™ 211 SERIES -48 VDC Battery Cabinet Installation & User Manual (Section 6033) | Rev. M... -
Page 23: Operation
(open) position (lockout/tagout). See Figure 21. Figure 21: Lockout/Tagout Padlock Tab for Locking Cabinet Door Padlock Tab for Battery Circuit Breaker Logout/Tagout Vertiv™ NetSure™ 211 SERIES -48 VDC Battery Cabinet Installation & User Manual (Section 6033) | Rev. M... - Page 24 Vertiv.com | Vertiv Headquarters, 1050 Dearborn Drive, Columbus, OH, 43085, USA © 2021 Vertiv Group Corp. All rights reserved. Vertiv™ and the Vertiv logo are trademarks or registered trademarks of Vertiv Group Corp. All other names and logos referred to are trade names, trademarks or registered trademarks of their respective owners. While every precaution has been taken to ensure accuracy and completeness here, Vertiv Group Corp.
Need help?
Do you have a question about the NetSure 211 Series and is the answer not in the manual?
Questions and answers