Download Print this page
kd frames 7936-RD-36 Instructions

kd frames 7936-RD-36 Instructions

Advertisement

Quick Links

Instructions for
Rolling Drawer
Manufactured by
394 Dairy Pak Rd. • Athens, GA 30607
kdframes.com • alan@kdframes.com
Parts:
(8) D-12 SLATS (12")
Tool Required: #2 Phillips-Head Screwdriver.
This futon frame is made with Tulip Poplar. Any green tint in the wood will change to light brown in a few weeks. This will
happen in 20 to 30 minutes if placed in direct sunlight. Tulip Poplar can be left unfinished, clear finished, stained, or
painted. I prefer the lighter stains over the darker ones because the wood is fairly porous. My favorite is a clear finish
with no stain. Satin polyurethane (oil or water based) works well.
Painting: It is best to start with an interior primer and lightly sand before painting.
Staining: Lightly sand before staining. Wipe stain on with a rag until you get the desired color. If you are going to use a
top coat (such as polyurethane), do not sand again until after the first coat, and then be careful not to sand away the
stain.
Finishing: All finishes work well with Tulip Poplar. A simple wax finish over stain (Minwax for example) is easy. An oil
finish such as Danish oil can be used. Or a clear top coat such as polyurethane works well to seal the wood. With
polyurethanes, the first coat acts as a sanding sealer. So you should lighty sand (180 - 220 grit sandpaper) after the first
coat, wipe the wood clean, and then build up coats for the desired effect.
Knockdown Frameworks, Inc. warrants all of its products for five years against any defects that are due to faulty materials or workmanship. We will promptly correct such
defects by repair or replacement, at our option, without charge. This warranty covers product defects only and will expire five years after date of purchase by the original
consumer purchaser, with proof of purchase required.
This warranty does not apply to damage caused by and resulting from misuse, neglect, accident, or improper operation, maintenance, storage, transportation, or handling of
the product. This warranty is for the original consumer purchaser for residential use only and does not apply if the product is used in any commercial application (such as rental
property). This warranty does not cover any incidental or consequential damages. If you feel that you have a claim under this warranty, please contact the store from which it
was purchased. If this is not possible, call 800-543-3393 for advice on handling your claim.
sku# 7936-RD-36
(4) D-18 CONNECTORS (18")
HARDWARE LIST:
H-4
2" WOOD SCREWS
H-10
HEX WRENCH
WHEELS
H-W
3/4" WOOD SCREWS
H-34
D-18 END PANELS (2)
D-36 SIDE PANELS (2)
8
1
4
8

Advertisement

loading

Summary of Contents for kd frames 7936-RD-36

  • Page 1 Instructions for HARDWARE LIST: 2” WOOD SCREWS Rolling Drawer H-10 HEX WRENCH WHEELS sku# 7936-RD-36 3/4” WOOD SCREWS H-34 Manufactured by 394 Dairy Pak Rd. • Athens, GA 30607 kdframes.com • alan@kdframes.com Parts: (8) D-12 SLATS (12”) (4) D-18 CONNECTORS (18”) D-18 END PANELS (2) Tool Required: #2 Phillips-Head Screwdriver.
  • Page 2 Attach two Wheels (H-W) to one of the End Panels (D-18) using four of the 3/4” Screws (H-34). Repeat for other End Panel. H-34 Push four Slats D-12 into one of the Attach the assemblies from Step 2 on one of Connectors D-18.