Advertisement
Quick Links
NOTE
All numerical values are in metric units [with U.S. customary units in brackets]. Dimensions are in millimeters [and inches]. Unless
otherwise specified, dimensions have a tolerance of ±0.13 [±.005] and angles have a tolerance of ±2°. Figures and illustrations are
for identification only and are not drawn to scale.
1. INTRODUCTION
This specification covers the requirements for application of DEUTSCH DRC16 header connector to be
mounted on a printed circuit board (PCB). The header is offered in 24, 40-pin arrangements which will
mate to the DEUTSCH DRC16 plug connector and comes in Right Angle and Straight versions.
The header receptacle consist of a housing, molded-in pins, pin spacer, flange seal and threaded
inserts. The header features a center threaded coupling system. Basic terms and features of this product
are provided below.
Housing
Threaded Insert
Flange Seal
Housing
Threaded Insert
Pin Seal
© 2020 TE Connectivity family of companies
All Rights Reserved
*Trademark
TE Connectivity, TE connectivity (logo), and TE (logo) are trademarks. Other logos, product, and/or company names may be trademarks of their respective owners.
DEUTSCH* DRC16 Header Connector System
Seal Surface
Keyway 2X
Mating Side
Standard Features All Arrangements
(DRC13-24PA shown as example)
Mating Side
Standard Features All Arrangements
(DRC10-24P shown as example)
PRODUCT INFORMATION 1-800-522-6752
Application Specification
PCB Side
Molded-in Pins
Molded-in Pins
PCB Side
This controlled document is subject to change.
For latest revision and Regional Customer Service,
visit our website at www.te.com.
114-151049
Rev A
13 NOV 2020
Pin Spacer
Molded-in
Solder Pots
Flange Seal
Sold Separately
1 of 11
Advertisement
Related Manuals for TE Connectivity DRC16
Summary of Contents for TE Connectivity DRC16
- Page 1 1 of 11 For latest revision and Regional Customer Service, All Rights Reserved visit our website at www.te.com. *Trademark TE Connectivity, TE connectivity (logo), and TE (logo) are trademarks. Other logos, product, and/or company names may be trademarks of their respective owners.
- Page 2 114-151049 1.1. Header Receptacle (Straight – 180°) DRC10-24PX DRC10-40P 1.2. Header Receptacle (Straight – 90°) DRC13-24PX DRC13-40PX Note: 1) X = A, B, C, D keys 1.3. Product Dimensions See connector product drawing for product dimensions. See section 2.3 2. REFERENCE MATERIAL 2.1.
- Page 3 DRC13-40PX-CG01 HDR, 40P, BLK, RA, M5 FLG, SN/NI/CU, A,B,C,D DRC13-40PX-G002 HDR, 40P, BLK, RA, 10-32 FLG, SN/NI/CU ,A,B,C,D 2.4. Specifications 108-151018 Product Specification DRC16 Series Connector System 114-151018 Application Specification DRC16 Series Connector System 2.5. Manuals 402-40 Solderability and Soldering 3.
- Page 4 114-151049 3.3. Characteristics A. Part Numbering System B. Pin Arrangement See product drawing for contact cavity marking C. Materials Header Housing: PPS GF40 (black) Pin Spacer: PTFE (white) Flange Seal: VMQ (red-orange) Pin Seal: VMQ (red-orange) Pin Contact: Brass Pin Plating (DRC10) Mating Side (Sn/Ni/Cu) PCB Side (Sn/Ni/Cu) Pin Plating (DRC13)
-
Page 5: Printed Circuit Board (Pcb) Layout
114-151049 D. Modification NOTES: 1) Modifications include but are not limited to the following list. 2) Modifications listed are for reference only and may not be available for every arrangement. Modification Description A004 Pins on PCB side C023 M5 Threaded Inserts on Flange M5 Threaded Inserts on Flange CG01 Pins on outside rows are Gold, All other Tin... -
Page 6: Panel Cutout
114-151049 3.5. Panel Cutout The header requires a panel cutout that allows the flange to be mounted on the inside of the panel. DRC10-24P-A004 DRC10-40P-A004 DRC13-24P DRC13-40P Note: Tolerance: ±.12 [.005] Sealing surface: 0.8 Ra [32 RMS] or better and 6 of 11 Rev A... - Page 7 Do not over torque the jackscrew bolt or possible damage to the housing(s) may occur. Note It is not recommended to use dielectric grease on either plug or receptacle. The DRC16 connectors are guaranteed to seal and perform per 108-151018 product performance without the application of grease or other foreign substance.
- Page 8 114-151049 3.9. Connector Unmating To unmate the plug and receptacle, use a M4 hex tool turn the jackscrew bolt counterclockwise until completely unmated. Separate plug from receptacle. M4 Hex Tool Jackscrew Bolt with M4 Hex Caution: Be careful not to damage the plug interface sea. Replace if necessary. 3.10.
- Page 9 114-151049 3.11. Panel Mounting Insert the header through the panel cutout then secure the header using 10-32 hardware (M5 for C023 and CG01 modifications). DRC10-24P requires 0510-014-2406 flange seal (sold separately). Mounting hardware (i.e. screw, washer, nut) are customer supplied. Screw length depend on application. Recommended torque: 2.26-2.83 [20-25 in-lbf].
- Page 10 114-151049 6. VISUAL AID Below shows a typical application of the DRC16 Header Connector. This illustration should be used by production personnel to ensure a correctly applied product. Applications which DO NOT appear correct should be inspected using the information in the preceding pages of this specification and in the instruction, material shipped with the product or tooling.
-
Page 11: Revision History
114-151049 7. REVISION HISTORY Brief Description of Change Date Apvd Initial Release 13 Nov 2020 11 of 11 Rev A...