Advertisement
Quick Links
Replacement Parts
Item Qty Description
1
1
Desk Assembly
2
2
Pivot, Friction
3
2
Bracket, Pivot
Screw, Phillips-head,
4
4
1/4-20 x 1/2"
5
1
T-tube
6
2
Nut, Hex, 1/4-20
7
1
Nut, Square, 1/4-20
8
2
Gripper, Inner Slide
9
1
Spring
10
1
Rod, Center
11
1
Tube, Inner
12
1
Base
13
1
Screw, Set, 5-16 x 1/4"
14
1
Pedal, Foot
15
1
Pin, Spring, 3/16"
Fasteners
4
Screw
1/2"
Hex Nut
6
Contents
Replacement Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Important User Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Required Tools. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Visit the Director's Stand web page at wengercorp.com for more information.
Note: Please read and understand these instructions before starting the assembly.
Note: If you need additional information, contact Wenger Corporation using the information below.
©Wenger Corporation 2022
Wenger Corporation, 555 Park Drive, P.O. Box 448, Owatonna, Minnesota 55060-0448
USA: (800) 4WENGER (493-6437) • Worldwide: +1-507-455-4100 • wengercorp.com
Components
7
Square Nut
Set Screw
13
1/4"
Printed in USA 2022-05
Assembly Instructions
Director's Stand
1
5
15
Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
6
8
7
11
2
3
9
4
10
12
13
14
Part #141A025-09
Advertisement
Related Manuals for Wenger Director's Stand
Summary of Contents for Wenger Director's Stand
- Page 1 Visit the Director's Stand web page at wengercorp.com for more information. Note: Please read and understand these instructions before starting the assembly. Note: If you need additional information, contact Wenger Corporation using the information below. ©Wenger Corporation 2022 Printed in USA 2022-05 Part #141A025-09 Wenger Corporation, 555 Park Drive, P.O.
- Page 2 Wenger Corporation. Wenger Corporation does not assume any responsibility for any errors that may appear in these instructions. In no event will Wenger Corporation be liable for technical or editorial omissions made herein, nor for direct, indirect, special, incidental, or consequential damages resulting from the use or defect of these instructions.
- Page 3 Assembly 4. Operate the foot pedal (14). 1. Loosen the set screw (13) in the base (12). The grippers (8) should move up and down 2. Insert the inner tube assembly (6-11) into 1/2". the base and push down until the pedal If not, verify that the inner tube assembly is pushes all the way up and the tube hits the all the way down and locked into the base.
- Page 4 Assembly (continued) 7. If the unit fails after step 5 or 6, adjust the grippers: a. Lift the T-tube off the inner tube. b. Loosen the top two hex nuts a few turns. c. Turn the grippers one turn up for easier release, or one turn down if the T-tube moves to freely.
Need help?
Do you have a question about the Director's Stand and is the answer not in the manual?
Questions and answers