Abus PR2800 Manual page 41

PSB2700: Door guard unit for opening the door a crack
Fig. 33
I. Assembly
2.
Note:
Until the lock casing is assembled on the lock side, the as-
sembly instructions for the PR2800 apply. Please check in
advance whether there is enough space for the complete
1. lock casing. The bar overhang from the lock casing of the
lock for two-turn closing is approx. 47 mm.
Installing the lock casing on the lock side.
1. When using PSB2700, first remove the plastic plug
1.
2.
3.
ø 4 mm
Fig. 34
1. 2.
Fig. 35
2.
II. Operation
1.
Fig. 36
Fig. 37
80
Replace lock tube insert:
from the lock tube (if necessary, use a screwdriver to
lever it through the small hole / Fig. 33).
Insert the bolt end cap for door guard function and
tighten all the way with self-tapping screw 5 x 12
from the PSB2700 set.
Drill out the cross-head of the screw with an HSS
drill bit Ø 4 mm (Fig. 34) and apply e.g. a touch-up
stick or lubricant to the outline of the hole (to
protect from corrosion).
Installing the lock casing:
2. The lock casing is pre-mounted for DIN right opening
doors. For DIN left opening doors, the door guard
will need to be shifted accordingly (Fig. 35).
3. Lock the bolt by turning the key once and remove
the key (door guard position). Loosen bolt clamping
screw 1. (Fig. 36) and slide the lock tube until a
suitable mounting point for the lock casing has
been reached. Make sure there is a stable surface for
screwing. Even out the folding thickness with
mounting plate and plastic washers, if necessary.
For folding thicknesses < 16 mm, we recommend
using the lock body support. Mark the lock casing
position. Tighten the door bar adjusting screw 1.
(Fig. 36).
4. For mounting the lock casing see „Mounting the lock
casing with mounting plate". Then knock the safety
plugs into the hexagon socket of the screws. (Fig. 37).
1. Close the bolt on the reinforced door bar lock until it
is in locked position.
The door can now be opened in locked position. In
locked position, the door guard will latch under its
own weight. The door guard must be raised in order
to unlock it
2. The door guard unit is maintenance free. Do not use
aggressive or caustic cleaning agents to clean the
surface.
ASP17:
The ASP17 mounting plate is suitable for the sturdy fixing of lock casings. It is used, in
particular, when the options for anchoring the reinforced door bar lock casings directly
and securely to the subsurface are inadequate (Fig. 38-40).
Scope of delivery ASP17
4x
6x
8x
6x
2x
G
4x
2x Fig. 38
Fig. 39
3
2
2
4
6
3* 2
5 5
6
4
2
2
3 * optional
Fig. 40
1. Establish the position of the lock casings and thus of
the mounting plate in accordance with the relevant
PR fitting instructions. Note: pay attention to
position – angled position of the plugs in relation to
the masonry.
2. For basic fitting, attach the mounting plate with
screws (E) and, if necessary, plugs (G) in the holes (2)
as an option.
3. Also fix the mounting plate with the long-shaft
fixing (C) through the angled holes (3).
4. If the hold is not adequate, the mounting plate can
also be anchored with a combination of M8
threaded rods through the two holes (4) and
injection mortar (not supplied).
5. As an option, additional longer long-shaft fixings
(C, not supplied) can be used for anchoring through
the central hole (3).
6. Fit cover (A).
7. Provide the lock casings of the reinforced door bar
with appropriate supports and screw in place in the
required position (fix with 2 selftapping screws (D).
If the rebate height is too small, it may be
necessary to use a lock body support.
GB
81