EK-Quantum Momentum2 ROG Strix X570-i Gaming D-RGB User Manual

Hide thumbs Also See for Momentum2 ROG Strix X570-i Gaming D-RGB:

Advertisement

Quick Links

EK-Quantum
Momentum
ROG Strix X570-i Gaming D-RGB
2
MONOBLOCK
USER GUIDE

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Momentum2 ROG Strix X570-i Gaming D-RGB and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for EK-Quantum Momentum2 ROG Strix X570-i Gaming D-RGB

  • Page 1 EK-Quantum Momentum ROG Strix X570-i Gaming D-RGB MONOBLOCK USER GUIDE...
  • Page 2 This product is intended for installation only by expert users. Please consult with a qualified technician for installation. Improper installation may result in damage to your equipment. EK Water Blocks assumes no liability whatsoever, expressed or implied, for the use of these products, nor their installation.
  • Page 3: Table Of Contents

    TABLE OF CONTENTS BOX CONTENTS WATER BLOCK DIMENSIONS TECHNICAL SPECIFICATIONS AND WATER BLOCK PARTS PREPARING THE MOTHERBOARD CUTTING AND PLACING THERMAL PADS APPLYING THERMAL COMPOUND PREPARING THE WATER BLOCK FOR INSTALLATION ATTACHING THE WATER BLOCK FITTINGS AND TUBING CONNECTING THE D-RGB LED STRIP TESTING THE LOOP WARRANTY SUPPORT AND SERVICE...
  • Page 4: Box Contents

    Thermal Pad F 1.0 mm 120 x 16 mm (3 pcs) M2.5x8 AX1 Screw (2 pcs) Thermal Grease (1 pc) Allen Key 2.5 mm (1 pc) EK-Quantum Momentum ROG Strix X570-i Gaming D-RGB Allen Key 2 mm (1 pc) - 4 -...
  • Page 5: Water Block Dimensions

    WATER BLOCK DIMENSIONS 27 mm 25.8 mm 64.9 mm 47.8 mm 9.5 mm 17.8 mm 20.5 mm 25.8 mm 122.2 mm 38.3 mm 148 mm - 5 -...
  • Page 6: Technical Specifications And Water Block Parts

    TECHNICAL SPECIFICATIONS AND WATER BLOCK PARTS Position Description Quantity 104436 Monoblock 103912 Coldplate (Nickel) 104435 Coldplate W (Nickel) 104433 Coldplate S (Nickel) 104438 TOP Acetal 104437 TOP Plexi 100258 Standoff M4/M2 x 2.5 103933 Jet Plate 103953 Mounting Screw 9033 Lock Washer 3.2 DIN6799 100500 Screw M4x12 DIN7991 INOX...
  • Page 7: Preparing The Motherboard

    PREPARING THE MOTHERBOARD SCREW M2x5.7 Important! Before starting, make sure to have a clean, flat SCREW surface to work on. It is recommended that you put foam M2x2.8 SCREW M2x5.4 or soft material to lay a motherboard and water block on. SCREW I/O FAN M2x19...
  • Page 8 STEP 3 I/O COVER Unscrew one (1) M2x2.8 Screw and remove the SSD M.2 disk (if installed). Remove the I/O cover plate. SCREW M2x2.8 For this step, you will need: SSD M.2 DISK Phillips Head Screwdriver STEP 3 STEP 4 METAL Remove all the marked screws and standoffs shown on image SCREW M2x2.8...
  • Page 9 STEP 5 Unscrew four (4) M3x10 Screws and remove two (2) AM4 brackets. M3x10 SCREW (4x) For this step, you will need: AM4 BRACKET AM4 BRACKET Phillips Head Screwdriver STEP 5 STEP 6 Turn the motherboard upside down. STEP 6 - 9 -...
  • Page 10 STEP 7 Unscrew two (2) M2x9 Screws, remove the Backplate heat STOCK spreader, and the Stock backplate. Unscrew three (3) M2x3 BACKPLATE Screws with a Polyamide washers. BACKPLATE HEAT SPREADER For this step, you will need: M2x3 SCREW Phillips Head Screwdriver WITH M2x9 SCREW POLYAMIDE...
  • Page 11: Cutting And Placing Thermal Pads

    CUTTING AND PLACING THERMAL PADS STEP 1 EK-Momentum ROG Strix X570-i Gaming D-RGB water block comes Thermal Pad F – 1.0 mm (120 x 16 mm) with Thermal Pads that have to be cut into smaller pieces to cover all the regulation area (Mosfet) on the motherboard.
  • Page 12: Applying Thermal Compound

    APPLYING THERMAL COMPOUND STEP 1 Apply the enclosed EK-TIM Ectotherm thermal grease (thermal compound) on the CPU heat spreader – IHS – and other necessary components as shown in the image. The layer of the thermal compound must be thin and even in thickness over the entire surface. The excessive or uneven application of thermal grease may lead to poor performance! For this step, you will need:...
  • Page 13: Attaching The Water Block

    ATTACHING THE WATER BLOCK STEP 1 Carefully place the water block onto the motherboard and align four (4) mounting screws with four (4) holes on the motherboard. STEP 1 STEP 2 Hold the water block and the motherboard and turn them upside down.
  • Page 14 STEP 3 Align the Backplate heat spreader with holes on the motherboard EXACT MOUNT BACKPLATE and tighten it with one(1) stored screw M2x9 and one (1) mounting screw M2.5x8 AX1 (Shown in the image). After attaching the BACKPLATE backplate, align the Velocity Backplate with Velocity Mounting HEATSPREADER...
  • Page 15 STEP 5 SCREW M2x5.7 Position the I/O cover plate on the water block and metal bracket. SCREW M2x5.4 Tighten the M2x2.8 and M2x5.7 Screws. Put M.2 disk heatsink straight down on the Audio card and connect the Audio card connector. IO COVER PLATE Tighten the M.2 disk heatsink with M2x19 and M2x5.4 Screws.
  • Page 16: Fittings And Tubing

    FITTINGS AND TUBING STEP 1 Screw-in two (2) G1/4 threaded male fittings. Attach the liquid cooling tubes and connect the water block to the cooling loop. TUBING EK recommends using EK fittings with all EK water blocks. EK-FITTING CAUTION: When using connectors other than EK fittings, pay special attention to the length of the fittings’...
  • Page 17: Connecting The D-Rgb Led Strip

    CONNECTING THE D-RGB LED STRIP STEP 1 Plug the 3-pin connector of the distribution plate D-RGB LED light to the D-RGB HEADER on the motherboard. The LED will work if the pin layout on the header is as follows: +5V, Digital, Empty, Ground.
  • Page 18: Warranty

    WARRANTY Our products are warranted against defects of materials and quality for a period of 24 months, starting with the date of delivery to the end-user. During this period, products will be repaired or have parts replaced at our discretion, provided that 1) the product is returned to the agent from whom it was purchased;...
  • Page 19: Support And Service

    SUPPORT AND SERVICE In case you need assistance or wish to order spare parts or a new mounting mechanism, please contact: https://www.ekwb.com/customer-support/ For spare parts orders, refer to the page with “TECHNICAL SPECIFICATIONS AND WATER BLOCK PARTS” where you can find the EAN number of each part you might need.

Table of Contents