1. Manuals
  2. Brands
  3. Digi Manuals
  4. Computer Hardware
  5. ConnectCore 9P 9215
  6. Manual

Digi ConnectCore 9P 9215 Manual

Hide thumbs Also See for ConnectCore 9P 9215:
Table of Contents

Advertisement

Quick Links

Download this manual
FIM Application Kit
Hardware Reference
90001074_B

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the ConnectCore 9P 9215 and is the answer not in the manual?

Questions and answers

Related Manuals for Digi ConnectCore 9P 9215

Summary of Contents for Digi ConnectCore 9P 9215

  • Page 1 FIM Application Kit Hardware Reference 90001074_B...
  • Page 2 Information in this document is subject to change without notice and does not represent a commitment on the part of Digi International. Digi provides this document “as is,” without warranty of any kind, expressed or implied, including, but not limited to, the implied warranties of fitness or merchantability for a particular purpose. Digi may make improvements and/or changes in this manual or in the product(s) and/or the program(s) described in this manual at any time.

  • Page 3: Table Of Contents

    Basic description ..................6     Connection to development board ............7     Connection to the ConnectCore 9P 9215 development board ............7     Connection to the Digi Connect ME 9210 development board ............8     Detailed description ................. 9  ...

  • Page 4: Overview

    The FIM_APPKIT board provides the external interfaces needed to test the different FIM interfaces available on the ConnectCore 9P 9215 and Digi Connect ME 9210 modules. The FIM_APPKIT is designed to be connected to the ConnectCore 9P 9215 development board and to the Digi Connect ME 9210 development board.

  • Page 5: Features

    FIM Application Kit - Hardware Reference 2 Features The following are major features of the FIM_APPKIT board:  Connector to connect the board to the ConnectCore 9P 9215 development board  Connector to connect the board to the Digi Connect ME 9210 development board ...

  • Page 6: Basic Description

    FIM Application Kit - Hardware Reference 3 Basic description The following figure shows the placement of the FIM_APPKIT board.

  • Page 7: Connection To Development Board

    The FIM_APPKIT will be connected in the X20, X21 rail to rail connectors of the ConnectCore 9P 9215 development board. The following figure shows how the FIM_APPKIT is connected to the ConnectCore 9P 9215 development board.

  • Page 8: Connection To The Digi Connect Me 9210 Development Board

    The following figure shows how the FIM_APPKIT is connected to the Digi Connect ME 9210 development board. Note: Please ensure you've set the IO lines on SW3 on the Digi Connect ME 9210 development board to GPIO to ensure proper use of the FIM_APPKIT interfaces.

  • Page 9: Detailed Description

    The FIM_APPKIT board provides interfaces to test the different firmware implemented on the FIMs of the ConnectCore 9P 9215 and Digi Connect ME 9210 modules. The FIMs are 8-bit microcontrollers embedded in the main microcontroller of the ConnectCore 9P 9215 and the Digi Connect ME 9210 modules.

  • Page 10: Types Of Interfaces

    FIM Application Kit - Hardware Reference In the following paragraphs the specific configuration for each interface will be described. 5.3 Types of interfaces According to how the interfaces of the FIM_APPKIT are connected to the FIMs of the development kits they are classified in two different types: ...

  • Page 11: Interface Table

    User LEDs FIM0 and FIM1 (6 LEDs) FIM0 (4-LEDs) * Note: A special version of the Digi Connect ME 9210 module is required to use the CAN interface. See the Digi Connect ME 9210 Hardware Reference Guide or http://www.digi.com/products/embeddedsolutions/digiconnectme9210.jsp#models for details.

  • Page 12: Interface Specification

    A UART interface is provided in the FIM_APPKIT to test the UART firmware implemented on the FIM0 of the ConnectCore 9P 9215 and Digi Connect ME 9210. The UART_0 interface provides RXD, TXD, RTS and CTS signals. To test the UART interface using two wire mode, only the TXD and RXD jumpers must be connected.
  • Page 13 The following figure shows the configuration jumpers that have to be connected to test the two wire UART interface using FIM0 of the ConnectCore 9P 9215. The following figure shows the configuration jumpers that have to be connected to test the four wire UART interface using FIM0 of the Digi Connect ME 9210.

  • Page 14: Uart_1

    Note: there is an RS232 transceiver between the UART interface and the 9-pin connector. The following figure shows the block diagram of the UART_1 interface. The following figure shows the configuration jumpers that have to be connected to test the four wire UART interface using FIM1 of the ConnectCore 9P 9215.

  • Page 15: Can_0

    FIM Application Kit - Hardware Reference The following figure shows the configuration jumpers that have to be connected to test the two wire UART interface using FIM1 of the ConnectCore 9P 9215. 5.5.3 CAN_0 A CAN interface is provided in the FIM_APPKIT to test the CAN firmware implemented on the FIM_0 of the ConnectCore 9P 9215.

  • Page 16: Can_1

    A CAN interface is provided in the FIM_APPKIT to test the CAN firmware implemented on the FIM1 of the ConnectCore 9P 9215 and Digi Connect ME 9210. One jumper (P14) is used on the board to connect or disconnect one 120R termination resistor to the CAN bus.

  • Page 17: Usb Device

    One USB device interface is provided in the FIM_APPKIT to test the USB device interface for the FIM0 and FIM1 of the ConnectCore 9P 9215 and Digi Connect ME 9210. The interface is fully compatible with USB 1.1 and USB 2.0.
  • Page 18 FIM Application Kit - Hardware Reference The following figure shows the block diagram of the USB device interface. The following figure shows the configuration jumpers that have to be connected to test the USB device interface using FIM0 of the ConnectCore 9P 9215.

  • Page 19: Sdio-Card

    9210 to an interrupt input (GPIO9/EINT0). The SDIO interface provides a write protect signal. This signal is connected in the ConnectCore 9P 9215 to an standard GPIO not assigned to the FIM. In the Digi Connect ME 9210 this signal is connected to the GPIO6.
  • Page 20 The following figure shows the configuration jumpers that have to be connected to test the SDIO interface using FIM0 of the ConnectCore 9P 9215. The following figure shows the configuration jumpers that have to be connected to test the SDIO...

  • Page 21: 1-Wire

    One 1-Wire interface is provided in the FIM_APPKIT to test the 1-Wire interface using FIM0 and FIM1 of the ConnectCore 9P 9215 and Digi Connect ME 9210. One DS2431 1-Wire EEPROM is mounted in the FIM_APPKIT to test the 1-Wire interface.
  • Page 22 The following figure shows the configuration jumpers that have to be connected to test the 1-Wire interface using FIM0 of the ConnectCore 9P 9215. The following figure shows the configuration jumpers that have to be connected to test the 1-Wire...

  • Page 23: I2S

    One audio interface is provided in the FIM_APPKIT to test the I2S interface using FIM0 and FIM1 of the ConnectCore 9P 9215 and Digi Connect ME 9210. The audio interface provides one UDA1334ATS audio decoder to play Wav audio files. This audio decoder is controlled with an I2S bus.
  • Page 24 The following figure shows the configuration jumpers that have to be connected to test the I2S interface using FIM0 of the ConnectCore 9P 9215. The following figure shows the configuration jumpers that have to be connected to test the I2S...

  • Page 25: Wiegand

    One Wiegand interface is provided in the FIM_APPKIT to test the Wiegand interface using FIM0 and FIM1 of the ConnectCore 9P 9215 and Digi Connect ME 9210. One 2mm, male, 3-pin connector is provided on the board to attach an external Wiegand device.
  • Page 26 FIM Application Kit - Hardware Reference The following figure shows the configuration jumpers that have to be connected to test the Wiegand interface using FIM0 of the ConnectCore 9P 9215. The following figure shows the configuration jumpers that have to be connected to test the...

  • Page 27: Parallel Bus

    One 2x14 pin, 2.54mm, male connector is provided in the FIM_APPKIT to be able to access to all the signals of the parallel bus implemented on the FIM0 and FIM1 of the ConnectCore 9P 9215. The following figure shows the block diagram of the parallel bus interface.

  • Page 28: User Buttons

    Two buttons are provided in the FIM_APPKIT to test a digital input firmware implemented on the FIM0 and FIM1 of the ConnectCore 9P 9215 and Digi Connect ME 9210. The following figure shows the block diagram of the user button interface.
  • Page 29 The following figure shows the configuration jumpers that have to be connected to test the buttons interface using FIM1 of the ConnectCore 9P 9215. The following figure shows the configuration jumpers that have to be connected to test the buttons...

  • Page 30: User Leds

    Six LEDs are provided in the FIM_APPKIT to test a digital output firmware implemented on the FIM0 and FIM1 of the ConnectCore 9P 9215 and Digi Connect ME 9210. The Digi Connect ME 9210 can control only four LEDs due to the reduced number of GPIO available on this module.
  • Page 31 The following figure shows the configuration jumpers that have to be connected to test the LED interface using FIM1 of the ConnectCore 9P 9215. The following figure shows the configuration jumpers that have to be connected to test the LED...

  • Page 32: Gpio Assignment Table

    FIM Application Kit - Hardware Reference 5.6 GPIO assignment table The following table shows the assignment between the GPIO of the ConnectCore 9P 9215 and the FIM signals for each FIM interface. GPIO UART_0 UART_1 CAN_0 CAN_1 USB DEV SDIO...
  • Page 33 FIM Application Kit - Hardware Reference The following table shows the assignment between the GPIO of the Digi Connect ME 9210 and the FIM signals for each FIM interface. GPIO UART_0 UART_1 CAN_0 CAN_1 USB DEV SDIO 1-WIRE WIEGAND Parallel...

  • Page 34: Board Connectors

    FIM Application Kit - Hardware Reference 6 Board Connectors 6.1 P1/P2: ConnectCore 9P 9215 This connector will be a 4-row, 20 pin, PC/104 type connector. Name Name Name Name GPIO_68 GPIO_69 GPIO_70 GPIO_71 GPIO_72 GPIO_73 GPIO_74 GPIO_75 GPIO_76 GPIO_77 GPIO_78...

  • Page 35: P6: Uart_0

    FIM Application Kit - Hardware Reference Name Comment GPIO6, 15 GPIO2, 14 GPIO2, 14 GPIO1 +3.3V 6.3 P6: UART_0 The UART_0 connector will be a 9-pin, sub-D, male connector. Name Comment UART_0_RXD UART_0_TXD UART_0_RTS# UART_0_CTS# 6.4 P8: UART_1 The UART_1 connector will be a 9-pin, sub-D, male connector. Name Comment UART_1_RXD...

  • Page 36: P11: Can_0

    FIM Application Kit - Hardware Reference 6.5 P11: CAN_0 The CAN_0 connector will be a 9-pin, sub-D, male connector. Name Comment CAN_0_L CAN_0_H 6.6 P15: CAN_1 The CAN_0 connector will be a 9-pin, sub-D, male connector. Name Comment CAN_1_L CAN_1_H 6.7 J1: USB Device The USB device connector will be a USB type-B connector.

  • Page 37: P36: Sd-Card

    FIM Application Kit - Hardware Reference 6.8 P36: SD-CARD The SDIO connector will be a normal type SD-Card header. Name Comment SD_D3 SD_CMD Command +3.3V SD_CLK SD_D0 SD_D1 SD_D2 SD_CD# Card Detection DT/WP SD_WP Write Protection 6.9 J3: 1-Wire The 1-Wire connector will be a RJ11 connector. Name Comment 1-WIRE_D...

  • Page 38: P32: Wiegand

    FIM Application Kit - Hardware Reference 6.11 P32: Wiegand The Wiegand connector will be a 3-pin, RM2.5, male connector Name Comment WG_D0 WG_D1 6.12 P37: Parallel bus The parallel bus connector will be a 2x14pin, RM2.54, male straight connector. Name Comment Name Comment...

  • Page 39: Factory Default Board Configuration

    FIM Application Kit - Hardware Reference 7 Factory Default Board Configuration By default the two CAN termination resistor jumpers will be closed. By default all the configuration jumpers will be open.

Table of Contents