4.0 Installation ................................7 Opening Rear Enclosure ..........................7 AI 500-070 Field Control Unit (FCU) ......................8 Solar Version Only ........................... 11 Testing AI FCU ............................12 Carmanah Technologies Corp. | 250 Bay St, Victoria, BC V9A 3K5, Canada | 1.250.380.0052 | customersupport@carmanah.com carmanah.com...
This manual will familiarize you with the features, operation standards and installation of Carmanah’s SPEEDCHECK-12 Applied Information (AI) Integration Kit. Failure to comply with the use, storage, maintenance, installation or placement instructions detailed in this manual could void the warranty.
Product can have sharp edges. Accidental movement of hinged components can cause injury. This guide is specific to the SPEEDCHECK-12 AI Integration Kit installation and is not a replacement for the complete SPEEDCHECK-12 product user manual.
5. Cable tie, 4-way, mounting base (2) 10. Adapter, 90°, SMA male to SMA female (2) 3.0 Tools and Materials Required The following tools and materials may be required to install the AI Integration Kit into your SPEEDCHECK-12 system: 1. Drill and 17/32” drill bit 5.
2. Apply diagonal pressure to the bottom right corner of the sign face then PULL on the key. 3. Once unlocked, the key can be removed. 4. Swing the display enclosure away from the rear enclosure. Carmanah Technologies Corp. | 250 Bay St, Victoria, BC V9A 3K5, Canada | 1.250.380.0052 | customersupport@carmanah.com carmanah.com...
Ensure the antenna is flush with the rear enclosure and tighten nut with a 19mm wrench. Carmanah Technologies Corp. | 250 Bay St, Victoria, BC V9A 3K5, Canada | 1.250.380.0052 | customersupport@carmanah.com...
Page 9
7. Install 16-pin and 4-pin harnesses into the AI FCU. 8. Thread two 90° coax adapters onto antenna connectors. Orient as shown below. Carmanah Technologies Corp. | 250 Bay St, Victoria, BC V9A 3K5, Canada | 1.250.380.0052 | customersupport@carmanah.com carmanah.com...
Page 10
13. Connect the 2-pin and 4-pin AI FCU connectors to the open receptacles on the display enclosure as shown below. All 2-pin connectors are interchangeable. Battery Only or AC w/ AI FCU Solar Kit w/ Battery & AI FCU Carmanah Technologies Corp. | 250 Bay St, Victoria, BC V9A 3K5, Canada | 1.250.380.0052 | customersupport@carmanah.com carmanah.com...
3. Once the sensor wire is inside the rear enclosure, connect it to the yellow wire shown below. To AI FCU harness solar sensor wire To charge controller Solar + Carmanah Technologies Corp. | 250 Bay St, Victoria, BC V9A 3K5, Canada | 1.250.380.0052 | customersupport@carmanah.com carmanah.com...
7. On the upper-left side of the browser, select the device name that matches the Device ID (the ID number labelled on the AI FCU). Ensure the equipment is not powering during installation. Recheck all wiring prior to energizing the system. Carmanah Technologies Corp. | 250 Bay St, Victoria, BC V9A 3K5, Canada | 1.250.380.0052 | customersupport@carmanah.com carmanah.com...
Page 13
11. To close, push the display enclosure against the rear enclosure and then apply diagonal pressure in the bottom right corner of the sign face. Once fully closed then PUSH the lock to secure in place. Carmanah Technologies Corp. | 250 Bay St, Victoria, BC V9A 3K5, Canada | 1.250.380.0052 | customersupport@carmanah.com...
Need help?
Do you have a question about the SPEEDCHECK-12 and is the answer not in the manual?
Questions and answers