Table of Contents
Advertisement
Quick Links
SA-500
SPECIAL PROGRAMMED WITH YELP OVERRIDE
Sound Hazard - Sound level from siren speaker (>120dBA @ 10 feet) may cause hearing damage.
Do not operate siren without adequate hearing protection for you and anyone in immediate vicinity.
(Ref. OSHA 1910.95 for occupational noise exposure guidelines)
TB0355A
Carson Manufacturing Co., Inc.
Phone: (888) 577-6877
TECHNICAL BULLETIN
YELP
WAIL
STBY
RADIO
INSTALLATION AND
OPERATING MANUAL
SA-500-16 14V
ON THE MAN/PHSR BUTTON
Carson is a trademark of Carson Manufacturing Company, Inc.
5451 North Rural Street
Indianapolis, IN 46220
Fax: (317) 254-2667
www.carsonsirens.com
MAN/PHSR
HORN
O
F
F
Page 1 of 8
VOLUME
RAD
PA
O
N
09/27/05
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Carson SA-500-16 14V
Summary of Contents for Carson SA-500-16 14V
- Page 1 Carson Manufacturing Co., Inc. 5451 North Rural Street Indianapolis, IN 46220 Phone: (888) 577-6877 Fax: (317) 254-2667 www.carsonsirens.com YELP WAIL MAN/PHSR STBY RADIO SA-500-16 14V Carson is a trademark of Carson Manufacturing Company, Inc. Page 1 of 8 VOLUME HORN 09/27/05...
- Page 2 Carson Manufacturing Co., Inc. makes no warranty of any kind with regard to this manual, including, but not limited to, the implied warranties of merchantability and fitness for a particular purpose.
- Page 3 Proper installation of the unit is essential for years of safe, reliable operation. Please read all instruction before installing the unit. Failure to follow these instructions can cause serious damage to the unit or vehicle and may void warranties. SAFETY PRECAUTIONS For the safety of the installer, vehicle operator, passengers and the community please observe the following safety precautions.
- Page 4 INSTALLER-SELECTABLE OPTIONS Carefully cutting programming resistor jumpers or traces on the printed circuit board inside the case can select various options. The cover must be removed to access the jumpers. The cover is held in place by a snap-fastener on the back of the unit.
- Page 5 ELECTRICAL CONNECTIONS Disconnect vehicle battery before making any electrical connections. Electrical connections to the unit are made using a removable terminal block plug located on the back. A label on the unit identifies the terminal function. You should install the connector on the unit before wiring. If the unit needs service the connector can be easily removed without unwiring the connector.
- Page 6 Sound Hazard - Sound level from siren speaker (>120dBA @ 10 feet) may cause hearing damage. Do not operate siren without adequate hearing protection for you and anyone in immediate vicinity. (Ref. OSHA 1910.95 for occupational noise exposure guidelines) The OFF/ON Rocker Power Switch controls the siren power. The siren may be left on any time the vehicle is in operation.
- Page 7 Horn not working Horn disabled If you have any questions concerning this or any other Carson product, please contact our Technical Service Department at (888) 577-6877. Many issues can be handled over the phone. We can also be reached via e-mail at service@carsonsirens.com...
- Page 8 Item Part # Description CP3966 Bolt, mounting, 1/4-20 X 3/8 (2 required) CP3571 Bracket, mounting CP4686 Button, white (for pushbutton switch) (substitute CP4837 red button) CP4687-10 Connector, 10-P header CP4688-10 Connector, 10-P terminal block plug CP4684 Control, volume, PA or RAD (1K ohm) CP4680-1 Cover with stud (does not include CP4679 Chassis) ATO/ATC 20A...
Need help?
Do you have a question about the SA-500-16 14V and is the answer not in the manual?
Questions and answers