Faqs - Panasonic F-VR901 Operating Instructions Manual

FAQs

Please confirm the following before you contact us for repair.
The air is cold during humidifying?
Q1
●
When humidification is set, moisture is
generated as air passes through the
humidifying filter that contains water. This
A
moisture removes heat in the air, and as a
result, the discharged air is at a lower
temperature than the air in the room.
There is no steam during humidifying?
Q2
●
T his product generates moisture by blowing
the humidifying filter containing water, not by
A
boiling the water, and hence does not
generate the steam.
The humidifying amount is reduced?
Q3
●
I n rainy season with high humidity or in cold
weather, the humidifying amount decreases
as you can see, for example, the washed
A
clothes are difficult to dry. The humidifying
amount changes depending on the room
temperature and humidity, and increases
when the weather is warm and dry.
The humidity indicator does not change?
Q4
■ T he humidity indicator remains
●
T he product may not sense the humidity
correctly depending on the installation place.
→Changetheinstallationplace.(P.31)
■ T he humidity indicator remains
●
The room size may be too large for the product?
A
→Refertotheapplicablefloorarea.(P.54)
Note
●
U se the humidity indicator only as a reference.
●
I t may be different from the display of the
household hygrometer.
●
T he humidity value will vary with the temperature.
●
The humidity may also vary with the airflow condition.
A buzz is heard from the air outlet?
Q5
●
T henoisecomesfromnanoe™generation
is normal. The noise may seem louder or
A
become silent depending on the usage
environment or operating mode, but this is
not a malfunction.
The humidifying filter is discolored?
Q6
●
T he filter may be discolored depending on
A
thewaterquality.Thiswillnotaffectthe
performance.
50
Dew condensation is on windows or walls?
Q7
●
E ven if the humidity in the room is moderate,
A
there may be dew condensation on a cold
window or wall.
The clean sign does not change?
The front panel remains open?
Q8
(Change the sensitivity of the sensor)
●
Such problems are likely to occur when the
sensitivity of the sensor is low/high.
You can change the sensitivity as you want.
(The initial setting is [中速 (Medium)].)
Stop operation, then press and hold
and
("AirVolume"indicatorsarelitinturn.)
A
Release the buttons when the sensitivity you
want is obtained.
(Air Volume indicator)
High: To set high sensitivity
Medium: To set medium sensitivity
Low: To set low sensitivity
Turning the front indication off.
Q9
●
T he front indication can be turned off.
●  P ress
simultaneously and hold for approximately
3 seconds while the product is operating or
A
off. (The front indication is turned off.)
To turn on again, press the buttons
●
simultaneously and hold for 3 seconds
again. (The front indication is lit.)
The front indication turns off while the
Q10
product is operating.
●
In"Lightsensormode",thelightsensordetects
the brightness in the room and automatically
adjusts the brightness of the front indication. If the
A
productisoperatingwith"Lightsensor1",the
front indication turns off when the room becomes
dark. (The humidity / PM2.5 concentration
indicator turns half on.) (P.49)
The presence sensor does not detect
Q11
anything?
●
The presence sensor does not operate for 2 minutes after
inserting the power plug as the product is warming up.
●
T he presence sensor cannot
detect people outside of its
range of detection, or if
there is furniture or other
A
objects in the way.
●
T he sensor may have
difficult detecting people due
to the temperature difference between people and the
surrounding area, or if the people are not moving much.
●
Is the presence sensor lens dirty?
→ R emoveanydirtwithacottonswab.
simultaneously.
and
Presence
sensor lens