Download  Print this page

In Case Of Difficulty - Kenwood VR-9050 Instruction Manual

Kenwood instruction manual audio video surround receiver vr-9050
Hide thumbs


In case of difficulty

Resetting the Microcomputer
The microcomputer may malfunction (unit cannot be operated, or
shows an erroneous display) if the power cord is unplugged while
the power is ON, or due to some other external factor. If this
happens, execute the following procedure to reset the
microcomputer and return the unit to its normal operating
No sound from the speakers.
The STANDBY indicator blinks and sound is
not output.
Sound is not output from one of the speakers.
Sound is not output from the surround
speakers and / or the center speaker, or their
sound is very small.
A humming noise is generated when the
PHONO input selector is selected.
When playing a Dolby Digital source signal
using a DVD player, the sound is cut off soon
after it starts.
No sound is produced during playback from
a DVD player.
A video source cannot be recorded
Radio stations cannot be received.
A station which was preset cannot be
received by pressing the corresponding
numeric key.
Unplug the power cord from the wall outlet, then plug it
back in while holding down the
• Please note that resetting the microcomputer will clear the contents
• The speaker cords are disconnected.
• VOLUME is set to the minimum position.
• MUTE is ON.
• The SPEAKERS switches are set to OFF.
• Headphones are connected to the PHONES
• Speaker cords are short-circuited.
• The speaker cord is disconnected.
• The speaker is not set up correctly.
• The surround speaker cords and/or the center
speaker cord is disconnected.
• The speaker is not set up correctly.
• A surround mode has not been engaged.
• The surround and/or center volume controls
are set to the minimum level.
• The audio cord from the record player is not
connected to the PHONO jacks.
• The record player is not grounded.
• There are many possible causes for this
problem, depending on the type of DVD player
• The input mode is set to digital manual.
• The software is copy-guarded.
• No antenna is connected.
• The broadcast band is not set properly.
• The frequency of the desired station is not
• Noise due to ignition noise from an automobile.
• Noise due to interference from an electric
• Noise due to a nearby TV set.
• The preset station belongs to a frequency that
cannot be received.
• The preset memory was cleared because the
power cord had been unplugged for a long
period of time.
of the memory and returns the unit to the state it was in when it left
the factory.
• C o n n e c t t h e m p r o p e r l y r e f e r r i n g t o
"Connecting the speakers"
• Adjust the volume to a proper level.
• Turn OFF the MUTE.
• Set the SPEAKERS switches to ON.
• Unplug the headphones plug.
• Turn the power off, eliminate the short-
circuiting, then turn on the power again.
• Connect it properly referring to "Connecting
the speakers".
• Set it up properly referring to "Speaker set-
• Connect it properly referring to "Connecting
the speakers".
• Set it up properly referring to "Speaker set-
• Select a surround mode.
• Adjust the speaker levels using the test tone.
• Insert the audio cord plugs securely into the
PHONO jacks.
• Connect the grounding wire to the GND
terminal on the rear panel.
• Set the input mode to digital manual before
starting playback of the Dolby Digital source.
• Press the INPUT MODE key to select to full
auto mode.
• Copy-guarded video software cannot be
• Connect an antenna.
• Set the broadcast band properly.
• Tune the frequency of the desired station.
• Install the outdoor antenna away from the
• Turn off the power to the appliance.
• Install the receiver farther away from the TV.
• Preset a station with a receivable frequency.
• Preset the station again.



  Related Manuals for Kenwood VR-9050

This manual is also suitable for: