Page 1
Compared to standard remote controls, the remote control supplied with this model has several operation modes. These modes enable the remote control to control other KENWOOD DVD players. In order to effectively use the remote control it is important to read the operating instructions and obtain a proper understanding of the remote control and how to switch its operation modes (etc.).
Once you have setup the remote control, you’ll be able to operate both this model and your KENWOOD DVD player using the remote control supplied with this model. AC 220-...
Surround modes ... 23 Surround play ... 25 DVD 6-channel playback (KRF-V6090D/KRF- V5090D only) ... 26 Convenient functions ... 27 Basic remote control operations for KENWOOD Remote DVD players ... 29 Control DVD player operation keys ... 29 In case of difficulty ... 30 Additional Specifications ...
You can enjoy a more impressive sound effect when ACTIVE EQ is turned on. IR (InfraRed) remote control In addition to the basic receiver operations, this IR remote control offers special features for supplied can also control KENWOOD DVD players directly without using the DVD Special features. ’s features.
(For KRF-V6090D/KRF-V5090D) Use to switch the power ON/STANDBY when the POWER is turned ON. STANDBY indicator 2 POWER ON/STANDBY (For VR-906/VR-905) Use to turn the power ON/STANDBY. STANDBY indicator 3 DIMMER key Use to select the REC MODE. Use to adjust the brightness of the display.
Each press switches the setting as follows: In DTS play mode 1 F-AUTO (digital input, analog input) 2 D-MANUAL (digital input) In CD/DVD, VIDEO2, DVD(VR-906/VR-905 only), DVD/ 6CH(KRF-V6090D/KRF-V5090D only) play mode 1 F-AUTO (digital input, analog input) º 2 D-MANUAL (digital input)
* For S-VIDEO connection! F o r C O M P O N E N T V I D E O connection@ VIDEO OUT (Yellow RCA pin cord) Connecting a DVD player (VR-906/VR-905 only) VIDEO MONITOR VIDEO 2 VIDEO 1 VIDEO 1...
Setting up the system Connecting audio components CAUTION Be sure to adhere to the following, or proper ventilation will be blocked causing damage or fire hazard. • Do not place any object impairing heat radiation onto the top of the unit. •...
* DVD IN input jack is used for either CD/DVD input or DVD input (VR-906/VR-905) or DVD/ 6CH input (KRF-V6090D/KRF- V5090D). A video component with digital audio outputs should be connected to the VIDEO 2 jacks.
Setting up the system Connecting video components (COMPONENT VIDEO) (Except for VR-905) If you have connected this model to a video component with COMPONENT jacks, you can get a better picture quality than by connecting to the S-VIDEO jacks. * DVD IN input jack is used for either CD/DVD input or DVD input.
Connect the video signal and analog audio signals to the VIDEO 2 jacks. (See “Connecting video components”.) COAXIAL OPTICAL VIDEO 2 CD / DVD DVD/6CH DIGITAL IN VR-906/VR-905 : DVD Optical fiber cable COAXIAL DIGITAL OUT (AUDIO) Component with DTS, Dolby Digital, or PCM...
When connecting a single & Surround Back speaker through a power amplifier to PRE OUT jack, connect it as above and select “SPEAKER” at speaker settings. VR-905/KRF-V5090D SURROUND GRAY BLUE SPEAKERS (8-16Ω) When connecting a Surround Surround Back speaker to this terminal, select “SPEAKER”...
FM 75Ω terminal. Listening position *Surround Back Right speaker Attach to the stand AM loop antenna 2 Insert cord. 3 Release lever. KRF-V6090D/ VR-906/VR-905 KRF-V5090D ANTENNA 75Ω FM indoor antenna VR-906/ VR-905 KRF-V6090D/ KRF-V5090D FM outdoor antenna Use an antenna adapter...
2 Use the MULTI CONTROL knob or MULTI CONTROL %/fi keys to select the speaker system setting. 1 CUSTOM 2 FULL RANGE : For selected KENWOOD speaker - for example, 3 2WAY 2SPKR : For selected KENWOOD speaker – for RECEIVER 4 2WAY 3SPKR : For selected KENWOOD speaker –...
Page 17
Preparing for surround sound If you have selected “NML” as the Front speakers setting, 1 CNTR NML (normal) : An average size Center speaker is connected to this model. 2 CNTR OFF : Center speaker setting mode to this model is OFF. 9 Press the SETUP key again to accept the setting.
Turning on this model 1 Turn on the power to the related components. 2 Turn on the power to this model by pressing POWER ON/ STANDBY (VR-906/VR-905) or POWER ON/OFF and ON/ STANDBY (KRF-V6090D/KRF-V5090D) key. Selecting the input mode If you have selected a component connected to the CD/DVD, VIDEO2,...
1 “TUNER” 2 “CD/DVD” 3 “TAPE” or “MD” 4 “VIDEO1” 5 “VIDEO2” 6 “DVD/6CH” (VR-906/VR-905 : “DVD”) 7 “AUX” Start playback from the selected source. Use the VOLUME CONTROL knob or VOLUME % / fi keys to adjust the volume.
Recording music in A-REC or M-REC mode DIMMER INPUT SELECTOR 1 Use the INPUT SELECTOR knob to select the source (CD/DVD, DVD/6CH (KRF-V6090D/KRF-V5090D), DVD (VR-906/VR-905) or VIDEO2) you want to record. 2 Set the MD or TAPE recorder to record. º...
Recording 3 Press and hold the DIMMER key for more than 2 seconds to select the A-REC or M-REC mode during digital input. 1 Rec mode off : The digital input record mode is switched off. 2 A-REC mode : The digital input signals (DTS, Dolby Digital, or PCM) are identified automatically and converted into stereo signals that are ready for recording.
Listening to radio broadcasts Presetting radio stations manually MEMORY MULTI CONTROL Tune to the station you want to store. Press the MEMORY key while receiving the station. Blinks for 20 seconds Proceed to step 3 within 20 seconds. (If more than 20 seconds elapse, press the MEMORY key again). Use the MULTI CONTROL knob or MULTI CONTROL % / fi...
Ambience effects This model is equipped with listening modes that allow you to enjoy an enhanced sonic ambience with a variety of video sources. In order to obtain the optimum effect from the surround modes, make sure to input the proper speaker settings beforehand. Surround modes The below speaker placements are for 5.1 channel surround sound system which are;...
Page 24
Ambience effects Dolby Digital The Dolby Digital surround format lets you enjoy up to 5.1 channels of digital surround sound from Dolby Digital program sources (such as Laserdisc or DVD software marked previous Dolby surround, Dolby Digital provides even better sound quality, greater spatial accuracy, and improved dynamic range.
Ambience effects Surround play The DTS compatible models can reproduce a CD, DVD, or LD carrying the DTS mark. DOLBY DIGITAL can be used when playing DVD or LD software bearing mark and DOLBY DIGITAL format digital broadcasts (etc.). DOLBY PRO LOGIC can be used when playing video, DVD, or LD software bearing the mark.
Ambience effects = THEATER : DSP Surround THEATER mode. ~ STADIUM : DSP Surround STADIUM mode. ! DISCO : DSP Surround DISCO mode. @ STEREO : Normal stereo playback. • Dolby Digital or DTS signal having more channels than the maximum number of playback channels available using this model’s current settings is input, downmixing is performed to match the number of available channels.
1 Press the SOUND key repeatedly until “NIGHT” appears on the display. • This can be selected only if CD/DVD, DVD/6CH (KRF-V6090D/KRF- V5090D), DVD (VR-906/VR-905) or VIDEO2 is selected as the source and the listen mode is set to “DOLBY DIGITAL” or “DTS”. DIMMER SOUND 2 Use the MULTI CONTROL knob or MULTI CONTROL %/fi...
Page 28
Ambience effects Dimension mode (Pro Logic II x Music mode and Pro Logic II Music mode only) When listening to music with certain recordings, you will also be able to achieve a suitable balance from all the speakers by adjusting the dimension mode.
Basic remote control operations for KENWOOD DVD players DVD player operation keys The remote control of this unit can control KENWOOD DVD players directly without using the remote control supplied with the DVD player. DV-4900, DV-4070B, DV-2070, DV-203, DVF-9010, DVF-K7010, DVF-5010, DVF-R9030, DVF-R7030, DVF-3530, DV-402, DV-5900, DV-5700, DVF-R9050, DVF-J6050, DV-505, DV-503, DV-502, DVF-3550, DVF-3050, DVF-R4050, DVF-605, DV-6050, DVF-R5060, DVF-3060, DVF-3060K, DV-705, DVF-R5070 ,DVF-3070, DVF-3080, DVF-N7080, DVF-8100, DVF-3200 and DVF-3250.
In case of difficulty Resetting the Microcomputer The microcomputer may malfunction (unit cannot be operated, or shows an erroneous display) if the power cord is unplugged while the power is ON, or due to some other external factor. If this happens, execute the following procedure to reset the microcomputer and return the unit to its normal operating condition.
Page 31
• The remote control has not been changed to the operation mode for the KENWOOD DVD player you wish to control. Remedy • Press the any of the Input Selector keys to select the appropriate operation mode.
VOLUME at -30dB level ... +8 dB (at 100 Hz) Notes 1. KENWOOD follows a policy of continuous advancements in development. For this reason specifications may be changed without notice. 2. The full performance may not be exhibited in an extremely cold location (under a water-freezing temperature).