Related Manuals for Advantech TPC-100W Series
Summary of Contents for Advantech TPC-100W Series
- Page 1 User Manual TPC-100W Series 電腦 7"/10.1"/15.6" Touch Panel Computer with ® ® Cortex -A53 Processor...
- Page 2 Note 2. “○” indicates that the content of the restricted substance does not exceed the defined concentration limit. 備考 3.“ － ” 係指該項限用物質為排除項目。 Note 3. “-” indicates that the restricted substance is not present in the product. 製造商：研華股份有限公司 地址：台北市內湖區瑞光路 26 巷 20 弄 1 號 電話：02-27927818 TPC-100W Series User Manual...
- Page 3 No part of this manual may be reproduced, copied, translated, or transmitted in any form or by any means without the prior written permission of Advantech Co., Ltd. The information provided in this manual is intended to be accurate and reliable.
- Page 4 TPC115WN31A2504-T, TPC115WN31A2505-T, TPC115WN31A2506-T Product Warranty (2 years) Advantech warrants the original purchaser that each of its products will be free from defects in materials and workmanship for two years from the date of purchase. This warranty does not apply to any products that have been repaired or altered by persons other than repair personnel authorized by Advantech, or products that have been subject to misuse, abuse, accident, or improper installation.
- Page 5 This product has passed the CE test for environmental specifications when shielded cables are used for external wiring. We recommend the use of shielded cables. This type of cable is available from Advantech. Please contact your local supplier for ordering information.
- Page 6 Replace the battery only with the same or equivalent type as recommended by the manufacturer. Discard used batteries according to the manufacturer's instructions.” Note! Notes provide additional optional information. TPC-100W Series User Manual...
- Page 7 This equipment is not suitable for use in locations where children are likely to be present. DISCLAIMER: These instructions are provided according to IEC 704-1 standards. Advantech disclaims all responsibility for the accuracy of any statements contained herein. Caution! Danger d'explosion si la batterie est mal remplace. Remplacer unique- ment par le meme type ou equivalent recommandé...
- Page 8 請不要把設備保存在超出我們建議的溫度範圍的環境，即不要低於 -20°C （-4 °F）或高於 60°C （140°F） ，否則可能會損壞設備。 注意：如果電池放置不正確，將有爆炸的危險。因此，只可以使用製造商推薦的 同一種或者同等型號的電池進行替換。請按照製造商的指示處理舊電池。 根據 IEC 704-1:1982 的規定，操作員所在位置的音量不可高於 70dB(A)。 限制區域：請勿將設備安裝於限制區域使用。 免責聲明：該安全指示符合 IEC 704-1 的要求。研華公司對其內容的準確性不 承擔任何法律責任。 使用過度恐傷害視力。 使用 30 分鐘請休息 10 分鐘。 未滿 2 歲幼兒不看螢幕，2 歲以上每天看螢幕不要超過 1 小時。 本產品為國內裝置使用時，其電源僅限使用架構電源模組所提供電源直流輸入， 不得使用交流電源及附加其他電源轉換裝置提供電源這者，其電源輸入電壓及電 流請依說明書規定使用。 TPC-100W Series User Manual viii...
- Page 9 Der arbeitsplatzbezogene Schalldruckpegel nach DIN 45 635 Teil 1000 beträgt 70dB(A) oder weiger. Haftungsausschluss: Die Bedienungsanleitungen wurden entsprechend der IEC-704-1 erstellt. Advantech lehnt jegliche Verantwortung für die Richtigkeit der in die- sem Zusammenhang getätigten Aussagen ab. TPC-100W Series User Manual...
- Page 10 Don't touch any components on the CPU card or other cards while the PC is on. Disconnect power before making any configuration changes. The sudden rush of power as you connect a jumper or install a card may damage sensitive elec- tronic components. TPC-100W Series User Manual...
-
Page 11: Table Of Contents
The Configuration and Connection of Bluetooth Module .... 23 Time And Date Setting ................27 CAN Setting .................... 28 Brightness Setting ................... 29 COM Setting.................... 29 Appendix A Pin Assignments .......31 M.2 Slot (E-Key)..................32 COM Port ....................33 TPC-100W Series User Manual... - Page 12 TPC-100W Series User Manual...
-
Page 13: Chapter 1 General Information
Chapter General Information... -
Page 14: Introduction
Introduction ® The TPC-100W series is a compact touch panel computer equipped with an NXP ® Cortex -A53 i.MX8M Mini quad-core processor, 7”/10.1”/15.6” TFT LCD display, multi-touch glass sensor,16GB of eMMC Storage. To ensure stable operation in harsh industrial environments, TPC-100W supports a wide operating temperature range (-20 ~ 60°... -
Page 15: Lcd Panel
Vibration Protection: 2 Grms random vibration (5 ~ 500 Hz) during operation (compliant with IEC60068-2-64) Shock Protection: 10 G shock under 11 ms operation (compliant with IEC60068-2-27) 1.2.6 EMC and Safety EMC: CE, FCC Class B, BSMI Safety: CB, UL, CCC TPC-100W Series User Manual... -
Page 16: Power
Insert the screws into every clamp and fasten them. These screws will push the mounting panel and fix the unit. The suggested mounting panel thickness is less than 6 mm (0.236”). TPC-100W Series User Manual... - Page 17 These screws will push the mounting panel and secure the unit. Accrocher la pince dans les trous et serrer les vis (couple: 2 kgf-cm) Ces vis vont pousser le panneau de montage et sécuriser l'unité. Size Screw (M4 x 25mm) & Clamper Q’ty TPC-100W Series User Manual...
-
Page 18: Dimensions And Cutout
Dimensions and Cutout TPC-100W Series User Manual... - Page 19 LED Indicator Off - “dark” ON - “Blue” Standby - “orange” TPC-100W Series User Manual...
- Page 20 TPC-100W Series User Manual...
-
Page 21: Chapter 2 System Setup
Chapter System Setup... -
Page 22: Transport And Unpacking
To avoid this, store the TPC system in a dry environment and bring the system to room temperature before powering it up. If condensation occurs, a delay time of approximately 12 hours must be allowed to ensure that the system is completely dry before being switched on. TPC-100W Series User Manual... -
Page 23: System Configuration
Warning! To avoid the system damage, the device may unable to incorrect or undefined switch may cause the system may be damaged when the power is turned on if the power source is not connected to the correct pins. TPC-100W Series User Manual... -
Page 24: M.2 Key-E 2230 Express Module Installation
TPC-100W provides 1 M.2 E key Express slot and allows users to expend functions like Wi-F and Bluetooth type modules. Open the rear bracket and configure the MINI PCI Express module on MINI PCI Express slot. (Refer to Appendix A1 for the detailed M.2 Slot (E-Key). TPC-100W Series User Manual... -
Page 25: System Power On
The terminal block is suitable for 12-24 AWG(12A). Torque value 7 lb-in. User copper conductors only. Must be installed by skilled person. Warning! The system may get damaged when the power is turned on and the power source is not connected to the correct pins. TPC-100W Series User Manual... -
Page 26: Cabinet Installation And Earth Grounding Setup
Install the TPC-100W system into the cabinet. A: Connect the cabinet to earth ground. B: Embed null TPC-100W system into the cabinet without any I/O cable and power. TPC-100W Series User Manual... - Page 27 F: Connect the V+ and V- of power supply to TPC-100W system. While completing step A to F step by step, you can supply power to TPC-100W sys- tem now. Note! Make sure all wires follow the installation guidelines or it may cause. TPC-100W Series User Manual...
- Page 28 TPC-100W Series User Manual...
-
Page 29: Chapter 3 Linux Yocto
Chapter Linux Yocto... -
Page 30: Arm Yocto 3.0
Vivante GPU accelerations for Wayland; The Hantro Video Processing Unit supports the following decoders: video/x-h265 video/x-vp9 video/x-h264 video/x-vp8 video/x-vp6-flash video/mpeg video/x-h263 video/x-flash-video video/x-divx video/x-xvid video/x-cavs video/x-wmv video/x-pn-realvideo video/x-raw TPC-100W Series User Manual... -
Page 31: Install Yocto 3.0 Software
(Note: You should check which partition is your microSD card firstly.) Second, after image is put into microSD card, use microSD card to update the image. Remove the screws from back cover. Due to COM port cover need to put down, then slide up. TPC-100W Series User Manual... - Page 32 Insert microSD card, then adjust switch as below order (red remark). TPC-100W Series User Manual...
- Page 33 Power on the system and open Terminal. Then input below commands. Waiting for update is finished. Then power off the system. Adjust switch as below location, remove microSD card. Power on again from eMMC. TPC-100W Series User Manual...
-
Page 34: Tpc-100W Module Extension
RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Or you can use below command to check. ls /sys/class/net/ can0 can1 eth0 eth1lo wifi0 If the WIFI node exists, the WIFI driver works normally. Enable WIFI. TPC-100W Series User Manual... -
Page 35: The Configuration And Connection Of Bluetooth Module
[CHG] Controller 00:19:88:5E:10:B1 Discovering: yes [NEW] Device 98:39:8E:1B:D8:88 Galaxy A5 (2016) [CHG] Device 98:39:8E:1B:D8:88 RSSI: -86 Now, Copy the MAC Address of your PC Stop scanning: ## 结束扫描 [bluetooth]# scan off Please record the MAC address you want to connect. TPC-100W Series User Manual... - Page 36 1 [bluetooth]# quit Using Obex profile to test the file transmission by Bluetooth. $ echo "helloworld" > /home/root/test.txt $ export $(dbus-launch) $ /usr/libexec/bluetooth/obexd -r /home/root -a -d & obexctl [obex]# connect 98:39:8E:1B:D8:88 [obex]# send <file> [obex]# quit TPC-100W Series User Manual...
- Page 37 Type = ethernet Powered = True Connected = True Tethering = False If “Powered = True”, it means WIFI is enabled. If WIFI is disabled, please use below command to enable it. 1 $ connmanctl enable wifi TPC-100W Series User Manual...
- Page 38 If the WIFI hotspot needs password, it will remind you to input. connmanctl connmanctl> agent on Agent registered connmanctl> connect wifi_88da1a7638bc_616476616e74656368_managed_psk Agent RequestInput wifi_88da1a7638bc_616476616e74656368_managed_psk Passphrase = [ Type=psk, Requirement=mandatory ] Passphrase? ****** Connected wifi_88da1a7638bc_616476616e74656368_managed_psk connmanctl> quit Now you can browse the internet by WIFI. TPC-100W Series User Manual...
-
Page 39: Time And Date Setting
Reset RTC hardware clock time (use current system time): sh-5.0# hwclock -w Reset system time (use RTC hardware clock time): sh-5.0# hwclock -s Set system time zone (use Taipei time): sh-5.0# cp /usr/share/zoneinfo/Asia/Taipei /etc/localtime sh-5.0# sync TPC-100W Series User Manual... -
Page 40: Can Setting
We’ll use “candump” to receive data, “cangen” & “cansend” to send data. The “can- gen” will send random data & ID and “cansend” will send specific data & ID to CAN- BUS. Send message (“123#R") to can0: sh-5.0# cansend can0 123#R Receive message from can0: sh-5.0# candump can0 TPC-100W Series User Manual... -
Page 41: Brightness Setting
Set com0 as RS485 mode and baud rate 115200. sh-5.0# echo out > /sys/class/gpio/gpio85/direction sh-5.0# echo out > /sys/class/gpio/gpio86/direction sh-5.0# echo 0 > /sys/class/gpio/gpio85/value sh-5.0# echo 1 > /sys/class/gpio/gpio86/value sh-5.0# stty -F /dev/ttymxc0 -echo -onlcr 115200 TPC-100W Series User Manual... - Page 42 TPC-100W Series User Manual...
-
Page 43: Appendix A Pin Assignments
Appendix Pin Assignments... -
Page 44: Slot (E-Key)
Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved SYSCLK Functional reset to Reserved RESET# the card Reserved Reserved Reserved Reserved I2C_DATA Reserved I2C_CLK Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved +3.3V +3.3V TPC-100W Series User Manual... -
Page 45: Com Port
COM Port 9-Pin Com Port Connector (COM1) RS232 RS422 RS485 9-Pin Com Port Connector (COM2/CAN) RS485 GND (isolation) TPC-100W Series User Manual... - Page 46 CAN BUS Pin define COM2 Pin define CAN BUS terminal (CN2) CN2 (1-2) CN2 (2-3) 120 ohm terminal default COM2 terminal (CN4) CN4 (1-2) default CN4 (2-3) 120 ohm terminal TPC-100W Series User Manual...
- Page 47 TPC-100W Series User Manual...
- Page 48 No part of this publication may be reproduced in any form or by any means, such as electronically, by photocopying, recording, or otherwise, without prior written permission from the publisher. All brand and product names are trademarks or registered trademarks of their respective companies. © Advantech Co., Ltd. 2022...