DeWalt DCE074R Original Instructions Manual page 34

EnGLIsH
In slope Mode: the arrow buttons are used to tilt the
laser head.
Height of Instrument Alert
The DCE074R and DCE079R/G have a built-in alarm feature that
alerts the operator if the unit is disturbed after the unit has self-
leveled. The laser unit will stop rotating, the control panel LED
indicator light will flash and the beeper will sound.
To Reset The Laser Unit for Continued Use
• Turn the unit off and back on again using the power button
on the laser unit control panel.
nOTE: Always recheck the laser setup after the Height of
Instrument Alert (Hi mode) has triggered.
Using the Remote Control (Fig. B, E)
(DCE079R/G)
The remote control allows one person to operate and setup the
laser from a distance. The remote control features a power/slope
mode button 21 , two arrows (rotation direction and tilt angle)
( 22 , 23 ) scan angle adjust button
axis selection button 20 . The LED light indicates a signal is
being transmitted.
Remote Control: Mode Button
Press the remote control mode button
into Scan Mode. In Scan Mode all laser unit functions shut off
except for a periodic blink from the power LED
panel of the laser unit. Press the remote control power button
again to "wake up" the laser unit.
nOTE: To completely power the laser unit off, the power button
on the control panel of the laser unit must be pressed. The laser
unit will also automatically power off if it is left in Sleep Mode
for 8 hours.
Remote Control: Mode Buttons
The Rotary Laser defaults to clockwise rotation of 360° at 600
RPM when powered on. Speed can be cycled through the
available RPM selections using the SPEED button
Remote Control: Slope Mode Button
(Fig B, E)
To activate Slope Mode press the remote control mode button
21 . To return to self-leveling mode and re-engage full self-
leveling, press and hold the mode button
setting the slope Direction:
When Slope Mode is activated, the unit automatically engages
the X- Axis. This allows the operator to slope the laser in the
direction of the X-Axis, as indicated by the "gunsights" on
the rollcage.
In certain situations, it may be desirable to slope the laser in
the Y-axis. The direction of Slope Mode can be changed back
and forth between the Y- and X-axes by pressing the X-Y axis
button 20
The LED indicator light on the laser unit control panel (Fig. B,
, ) will indicate the slope direction that is selected. The
10 11
selected axis is identified by LED lights (
32
18 speed button 19 and
18 to put the laser unit
on the control
9
19
21 again .
12 , 13 ).
setting the amount of slope:
Once Slope Mode is activated and the desired axis is active the
amount of slope can be adjusted as follows:
• Use the remote control up and down arrow buttons (Fig. E:
( 22 , 23 ) to tilt the laser rotor head up and down.
Remote Control: Arrow Buttons
The arrow buttons ( 22 , 23
depending on the operating mode of the laser unit.
In self-Leveling Horizontal Mode:
• The up and down arrows
line in Scan Mode.
• The left and right arrows
beam in Scan Mode or Pointing Mode (0 rpm).
In self-Leveling Vertical Mode:
• The arrow buttons ( 22
line in Scan Mode. and move the laser beam left and right.
In slope Mode:
• The arrow buttons (
22
up or down in the X and Y directions as marked on the
protective roll cage of the laser unit.
Remote Control: Speed/Rotation Button
The speed/rotation button
laser beam through its 4 preset speeds.
nOTE: The speed/rotation button performs the same function
as the speed/rotation button on the control panel of the
laser unit.
Remote Control: Scan Mode Button
The scan mode button 18
sweep back and forth, creating a short, bright laser line. This
short line is much brighter and more visible than when the unit
is in full rotation mode.
Using scan Mode:
• To enter Scan Mode, push and release the scan mode
button. To exit Scan Mode, push and release the
button again.
• The size and direction of the scan zone can be controlled
with the arrow buttons on the laser unit control panel or
the remote control. For a more detailed explanation, refer to
arrow Buttons under Laser Control Panel Buttons
LASER ACCESSORIES

WARNING: Since accessories, other than those offered
by D WALT, have not been tested with this product, use
e
of such accessories with this tool could be hazardous.
To reduce the risk of injury, only D
accessories should be used with this product.
Consult your dealer for further information on the
appropriate accessories.
If you need assistance in locating any accessory, visit our
website www.D WALT.com
e
) are used for different functions
23 adjust the length of the laser
22 adjust the direction of the laser
, 23 ) adjust the position of the laser
, ) are used to tilt the laser head
23
19 is used to adjust the speed of the
15˚/45˚/90˚
is used to make the laser head
WALT recommended
e