Power Button - DeWalt DCE074R Original Instructions Manual

• When working with the D
Detector, set the laser's rotation speed to the
fastest setting.
• If the laser is dropped or suffers a sharp blow, have
the calibration system checked by a qualified service
centre before using the laser.
Laser Control Panel (Fig. B)
The laser is primarily controlled by the power button
mode button , the speed button
2
button , These features are subsequently modified using the
4
Axis selection button 5 (DCE079R/G only), and two direction/
elevation adjustment buttons (
adjustment buttons control the rotational direction of the laser
head as well as adjust the elevation of the beam when the unit
is in slope mode.
Four LED indicator lights are on the control panel: power
9 , X-axis leveling 13 (DCE079R/G only), Y-axis leveling
(DCE079R/G only) and Hi mode (anti drift)
Turning the Laser on (Fig. A, B)
1. Insert the fully charged 18V battery pack as shown in
Figure A .
2. Gently press the power button
The power LED indicator light
-
unit will self level. The beam rotates once level at the
default settings of 600 RPM in the clockwise direction.
- Self leveling mode is activated automatically after the
unit is powered on.
- Hi Mode (Anti- Drift) is activated automatically after 10
sec. The Hi LED 8 will illuminate when active.
- Press the speed/rotation button
speed. The direction can be changed using buttons
and 7 .
The beam can be set to scan in 0°, 15°, 45° or 90° degree
-
mode using button
Turning the Laser Off
Press the the power button for 3 sec to turn the laser off. The
power LED indicator light will no longer be illuminated.
Laser Control Panel Buttons (Fig, B, J)

Power Button

To completely power the laser unit off, the power button on
the control panel of the laser unit must be pressed for 3 sec. The
laser unit will also automatically power off if it is left in Sleep
Mode for 8 hours.
nOTE: Press the remote control power button to put the laser
unit into Sleep Mode. In Sleep Mode all laser unit functions
shut off except for a periodic blink from the power LED on the
control panel of the laser unit. Press the remote control power
button again to "wake up" the laser unit.
WALT Digital Laser
e
1
and the scan mode
3
6 , 7 ). The direction/elevation
.
8
1 to power the laser on.
will illuminate and the
9
3 to adjust the rotation
4 .
Speed/Rotation Button
The speed button
laser beam through its 4 preset speeds.
The head speed will cycle through 4 speeds, then repeat the
sequence as the speed/rotation button is pressed.
nOTE: The speed/rotation button performs the same function
as the speed/rotation button on the remote control.
, the
Scan Mode Button
The scan mode button
back and forth, creating a short, bright laser line. This short line
is much brighter and more visible than when the unit is in full
rotation mode.
Using scan Mode:
• To enter Scan Mode, push and release the scan mode
button 4 . To cycle through the scan angles, continue to
12
press the button until you reach the angle desired. Repeat
the sequence to change angles.
• The direction of the scan zone can be controlled with the
arrow buttons (
remote control.
Slope Mode Button
• To activate Slope Mode press the laser keypad slope
mode button
• To return to self leveling mode and re-engage full self-
leveling, press and hold the mode button
setting the slope Direction
When Slope Mode is activated, the unit automatically engages
the X- Axis. This allows the operator to slope the laser in the
direction of the X-Axis, as indicated by the "gunsights" on
the rollcage.
6
The LED indicator light on the laser unit control panel (Fig. B,
10 , 11 ) will indicate the slope direction that is selected. The
selected axis is identified by LED lights
DCE079R/G only: In certain situations, it may be desirable to
slope the laser in the Y-axis. The direction of Slope Mode can be
changed back and forth between the Y- and X-axes by pressing
the X-Y axis button
setting the amount of slope
Once Slope Mode is activated and the desired axis is active the
amount of slope can be adjusted as follows:
• Use the laser control panel up and down arrow buttons
(Fig. B, 6 ,
Arrow Buttons (Fig. J)
The arrow buttons (
depending on the operating mode of the laser unit.
In self-Leveling Horizontal Mode: the arrows buttons adjust
the direction of the laser beam clockwise or counter clockwise
during rotation or Scan Mode.
In self-Leveling Vertical Mode: the arrow buttons move the
laser beam left and right.
3 is used to adjust the rotation speed of the
15˚/45˚/90˚
4 is used to make the laser head sweep
6 , 7 ) on the laser unit control panel or the
2 .
12
5 on the keypad.
7 ) to tilt the laser rotor head up and down.
6 , 7 ) are used for different functions
EnGLIsH
again.
2
, 13 .
31