Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Nilfisk-Advance Topax Hygiene System
Summary of Contents for Nilfisk-Advance Topax Hygiene System
- Page 1 User Guide Topax Hygiene System S Booster MP44/MP66/MP88 Vers. 1.0 – 01.01.2012...
-
Page 2: Table Of Contents
Contents Preface ......................3 Application ....................3 Warnings ..................... 3 Safety Instructions ..................4 Standard Unit ..................... 5 Description of Function ..................6 Flow Chart....................6 Installation ......................7 General ....................... 7 Mounting ..................... 7 Pipe Work ....................7 Priming ......................8 Electric connection .................. -
Page 3: Preface
Preface The S Booster is designed for the boosting and transfer of clean water to cleaning equipment within the food industry. It is important that your operational staff reads these directions for use prior to the installation and start of operation. Operation as laid down in these directions for use will ensure an optimum level of hygiene in your factory and a minimum level of maintenance and repair work. -
Page 4: Safety Instructions
Safety Instructions Repairs are only to be carried out when the unit is switched off. Warning! WARNING The unit is only to be used for purposes as described in this user guide. WARNING Dry running for even a very short period of time can cause dry running not detected by our dry running security. -
Page 5: Standard Unit
Standard Unit The Booster consists of two pumps mounted on a floor frame, non-return valves, manifold (inlet) with flow switch, manifold (outlet) and Booster controller unit. 119000068 Inlet Manifold Manifold Outlet CRIE Pump Ball valve SF Pump Non return valve Pressure transmitter Temperature sensor MPC-E controller... -
Page 6: Description Of Function
Description of Function Flow Chart Pressure transmitter Pressure transmitter CRIE Pump Ball valve SF Pump Non return valve Pressure gauge... -
Page 7: Installation
Installation General The Booster unit must be installed and all electric connections must be performed in accordance with local regulations. Mounting The Booster unit must be placed in a well ventilated room, in order to secure adequate air supply for cooling of the pump engines. This also applies when the motors are in operation. -
Page 8: Priming
Priming Do not start the pumps until filled with water! Electric connection Electrical connections must be carried out in accordance with local regulations and must only be carried out by authorised engineers. The motors are started directly on line (Star delta, optional). The motors are fitted with built in thermal switches. -
Page 9: Function
Function 5.0 Operational Instructions CAUTION Ensure that the spray gun or low pressure valve is closed before start The S Booster is bled by loosening the bleeding screw at the top of the pump stations. The screw must be left open for approx. 4 minutes allowing water to run out. -
Page 10: Technical Data
Technical Data Data MP44 MP66 MP88 Siehe Siehe Siehe Supply voltage Typenschilder auf Typenschilder auf Typenschilder auf Motoren Motoren Motoren Isolation class IP54 IP54 IP54 Max. Leistungsverbrauch 60 kW 90 kW 120 kW Control voltage 24 VAC 24 VAC 24 VAC Capacity 0-44m 0-66m... -
Page 11: Maintenance
Maintenance Instructions Depending on usage, maintenance should be undertaken by an authorised service engineer at least once a year in order to prevent defects and failure of operation. Authorised engineers are persons who, due to their skills and experience, have sufficient knowledge of low pressure cleaning systems or similar and are confident with the state work safety regulations, accident preventive regulations, guidelines and generally acknowledged technical regulations such as DIN-norms and VDE-provisions. -
Page 12: Components
Components Exploded Drawing Booster MP Unit with Spare Spart List 119000068... - Page 13 Pos. no. Article no. Description Number Inlet 313800 Pressure transmitter 0604221 CRIE 15-17 Pump 2 (3) (4) 852900 CRN 15-16SF Pump 2 (3) (4) 659000 Manometer 0-60 Bar 313800 Pressure transmitter Outlet 334604 Ball valve 4 (6) (8) 359944 Non return valve 2 (3) (4) 0601444 Temperature sensor...
-
Page 14: Warranty
Warranty Attention! Our guarantee is given for a period of 12 months from delivery on all parts which have provable become unfit for use due to material, construction or manufacturing defects as well as inadequate work. The guarantee compensation will occur in the shape of either reimbursement, replacement or repair of the defective or damaged part at our works. - Page 15 CE Declaration of Conformity Nilfisk-ALTO Food Division declares that the machine: No.: 119000149 Name: Booster MP44 Type: Booster, MP - is manufactured in conformity with the following standards: Directive 2006/42/CE of the European Parliament and of the Council of 22 June 1998 on the approximation of the laws of the Member States relating to machinery.
- Page 16 CE Declaration of Conformity Nilfisk-ALTO Food Division declares that the machine: No.: 119000068 Name: Booster MP66 Type: Booster, MP - is manufactured in conformity with the following standards: Directive 2006/42/CE of the European Parliament and of the Council of 22 June 1998 on the approximation of the laws of the Member States relating to machinery.
- Page 17 CE Declaration of Conformity Nilfisk-ALTO Food Division declares that the machine: No.: 119000149 Name: Booster MP88 Type: Booster, MP - is manufactured in conformity with the following standards: Directive 2006/42/CE of the European Parliament and of the Council of 22 June 1998 on the approximation of the laws of the Member States relating to machinery.
Need help?
Do you have a question about the Topax Hygiene System and is the answer not in the manual?
Questions and answers