Advertisement
Available languages
Available languages
• 5-6 (high stroke rate) - use for sawing soft mate-
rials (soft wood, insulating materials, etc�)�
Following setting up the number of stroke
rate of the saw blade 18 it is recommend-
ed to make a test saw cut using a spare
piece of the blank part (made of the same
material as the part to be processed).
When operating your power tool at a low speed for a
long time, it has to be cooled down for 3 minutes� To
do it, set a maximum stroke rate and leave your power
tool to run idle�
Pendulum rate selection
Pendulum rate facilitates selecting the optimal sawing
regime (feed velocity, the appearance of the saw cut,
etc�) for the processed material�
With each downward move the saw blade 18 is driven
back from the blank part which improves the release of
the sawdust, reduces the heating up and increases the
operating life of the saw blade 18� Moreover the reduc-
tion of the feed force allows the worker to operate the
instrument without getting tired�
The degree of the pendulum strike may be changed
when operating the power tool� The lever for pendulum
stroke adjustment 13 allows setting four steps of the
pendulum stroke:
Step 0:
No pendulum action;
Step I:
Small pendulum action;
Step II:
Medium pendulum action;
Step III:
Large pendulum action�
It is recommended to consider the following rec-
ommendations when selecting the degree of the
pendulum rate:
• when the edge of the saw cut must be exact and
clean, select small pendulum rate or switch the pen-
dulum rate off;
• switch the pendulum rate off when processing thin
(sheet metal, sheet plastic, etc�) or hard materials
(alloy-free steel, non-ferrous metals, etc�);
• when sawing soft materials (soft wood, etc�) se-
lect large pendulum rate; it will increase the speed
of the operation, however the quality of the saw cut
may be reduced�
It is recommended to make a test saw
cut using a spare piece of the blank part
(made of the same material as the blank
part to be processed) after the pendulum
rate is selected.
LED lamp
When the on / off switch 1 is pushed, the LED lamp 9
is automatically switched on that allows to carry out
works in low light conditions�
Dust blowing system
When the on / off switch 1 is pushed, the dust blow-
ing system is automatically switched on and enables a
clear view of cutting line�
Plastic overlay
Plastic overlay 15 of the base plate 14 prevents dam-
age the surface of treated workpiece�
Protection against contact with saw blade
Contact protector 10 prevents accidental contact with
saw blade 18 and improves safety of work perfor-
mance�
Recommendations on the power tool op-
eration
Selecting the saw blade
Saw blades 18 of T-type may be used
with all of the jigsaw models.
Before starting the operation, please select the appro-
priate type of the saw blade 18 which should corre-
spond to the sawed material, sawing regime and the
quality of the edge of the saw cut� The designation of
the saw blade is printed on the package; you may also
ask the salesperson�
General guidelines for cutting
Make a test saw cut using a spare piece of
the blank part (made of the same material
as the material of the blank part) in order
to make sure that the saw blade 18, the
sawing speed and the pendulum strike have been
selected appropriately.
• Make sure that the blank part is tightly fastened and
that all of the metal pieces (nails, screw nails, etc�)
have been removed from it�
• Turn the power tool on before the saw blade 18
comes in contact with the blank part� Do not use extra
force; the operation requires some time� Extra force
will not speed up the operating process, but it will over-
load the tool�
• When the teeth of the saw blade 18 are too large for
the blank part (excessive vibration, splitting and chip-
ping of the processed surface will serve as a sign of
the teeth being too large), turn off the power tool im-
mediately and replace the saw blade 18 with the ap-
propriate blade�
• If the saw blade 18 jams during the operation, turn
off the power tool immediately and try to expand the
saw cut, then carefully remove the saw blade 18 from
the saw cut�
• After the cutting is finished, first turn the power tool
off and then remove the saw blade 18 from the saw cut�
When cutting certain materials (like met-
als), the saw blade 18 may heat up ex-
cessively, therefore it is recommended
to use cooling or lubricating substances
which are to be applied to the point where the saw
blade 18 comes in contact with the blank part.
English
26
Advertisement
