Beko WMB 61231CSPTM User Manual page 31

Child Lock
Use Child Lock function to prevent children from tampering
with the machine. Thus you can avoid any changes in a
running programme.
C
If the Programme Selection knob is turned when the
Child Lock is active, "Con" appears on the display.
The Child Lock does not allow any change in the
programmes and the selected temperature, speed
and auxiliary functions.
C
Even if another programme is selected with the
Programme Selection knob while the Child Lock is
active, previously selected programme will continue
running.
To activate the Child Lock:
Press and hold 1 and 2
st nd
3 seconds. The lights on the 1
buttons will flash, and "C03", "C02", "C01" will appear
on the display respectively while you keep the buttons
pressed for 3 seconds. Then, "Con" will appear on the
display indicating that the Child Lock is activated. If you
press any button or turn the Programme Selection knob
when the Child Lock is active, same phrase will appear on
the display. The lights on the 1st and 2nd auxiliary function
buttons that are used to deactivate the Child Lock will blink
3 times.
To deactivate the Child Lock:
Press and hold 1 and 2
st nd
seconds while any programme is running. The lights on the
1 and 2 Auxiliary Function buttons will flash, and "C03",
st nd
"C02", "C01" will appear on the display respectively while
you keep the buttons pressed for 3 seconds. Then, "COFF"
will appear on the display indicating that the Child Lock is
deactivated.
C
In addition to the method above, to deactivate the
Child Lock, switch the Programme Selection knob to
On / Off position when no programme is running, and
select another programme.
C
Child Lock is not deactivated after power failures or
when the machine is unplugged.
Progress of programme
Progress of a running programme can be followed from
the Programme Follow-up indicator. At the beginning of
every programme step, the relevant indicator light will turn
on and light of the completed step will turn off.
You can change the auxiliary functions, speed and
temperature settings without stopping the programme flow
while the programme is running. To do this, the change
you are going to make must be in a step after the running
programme step. If the change is not compatible, relevant
lights will flash for 3 times.
C
If the machine does not pass to the spinning step,
Rinse Hold function might be active or the automatic
unbalanced load detection system might be activated
due to the unbalanced distribution of the laundry in
the machine.
Loading door lock
There is a locking system on the loading door of the
machine that prevents opening of the door in cases when
the water level is unsuitable.
Auxiliary Function buttons for
and 2 Auxiliary Function
st nd
auxiliary function buttons for 3
Loading door light will start flashing when the machine
is switched to Pause mode. Machine checks the level of
the water inside. If the level is suitable, Loading Door light
illuminates steadily within 1-2 minutes and the loading
door can be opened.
If the level is unsuitable, Loading Door light turns off and
the loading door cannot be opened. If you are obliged to
open the Loading Door while the Loading Door light is off,
you have to cancel the current programme; see "Canceling
the programme".
Changing the selections after
programme has started
Switching the machine to pause mode
Press the Start / Pause button to switch the machine to
pause mode while a programme is running. The light of
the step which the machine is in starts flashing in the
Programme Follow-up indicator to show that the machine
has been switched to the pause mode.
Also, when the loading door is ready to be opened, Loading
Door light will also illuminate continuously in addition to the
programme step light.
Changing the speed and temperature
settings for auxiliary functions
Depending on the step the programme has reached,
you may cancel or activate the auxiliary functions; see,
"Auxiliary function selection".
You may also change the speed and temperature settings;
see, "Spin speed selection" and "Temperature selection".
C
If no change is allowed, the relevant light will flash for
3 times.
Adding or taking out laundry
Press the Start / Pause button to switch the machine to
pause mode. The programme follow-up light of the relevant
step during which the machine was switched into the
pause mode will flash.
Wait until the Loading Door can be opened. Open the
Loading Door and add or take out the laundry. Close
the Loading Door. Make changes in auxiliary functions,
temperature and speed settings if necessary. Press Start /
Pause button to start the machine.
Canceling the programme
To cancel the programme, turn the Programme Selection
knob to select another programme. Previous programme
will be canceled. End / Cancel light will flash continuously
to notify that the programme has been canceled.
Pump function is activated for 1-2 minutes regardless of
the programme step, and whether there is water in the
machine or not. After this period, your machine will be
ready to start with the first step of the new programme.
C
Depending on the step where the programme was
canceled in, you may have to put detergent and
softener again for the programme you have selected
anew.
End of programme
"End" appears on the display at the end of the programme.
Wait until the loading door light illuminates steadily. Press
On / Off button to switch off the machine. Take out your
laundry and close the loading door. Your machine is ready
for the next washing cycle.
31
EN