BWI Eagle AIR-EAGLE SR PLUS Product Information Bulletin

AIR-EAGLE
2.4 GHz RF Transmitter
MODEL 36U-HH-9
DESCRIPTION
The A -E SR PLUS TX s a handheld R.F. transmitter capable of
IR AGLE I
sending up to sixteen unique digital commands to an Air-Eagle SR
Receiver located up to 600 feet away. Any number of transmitters and
receivers can be combined to create a medium-range radio frequency
system that operates hazardous or hard-to-reach equipment from safe,
convenient locations. Eight user-programmable frequencies allow
multiple systems to operate simultaneously in the same area without
interference. This transmitter will automatically go into "sleep" mode
when no buttons are being depressed on the unit to dramatically
extend battery life.
APPROVALS
United States (FCC)
Canada (IC)
Europe (CE)
INITIAL SET-UP
This transmitter comes factory set to frequency 1 and power level 4 (max
range of 600 feet). If you wish to change the default settings, follow the
instructions for FREQUENCY PROGRAMMING AND POWER LEVEL
PROGRAMMING on page 2.
GENERAL OPERATION
This transmitter sends up to 16 independent commands. Each button
sends an RF Code for that channel. Button 1 transmits channel 1
commands, button 2 transmits channel 2 commands etc. To send
commands 9 thru 16, the P/Shift button must be used. As noted under
CONTROLS & INDICATORS, the P/Shift button serves two purposes. As
the "P" button, it allows you to program the transmitter to operate on a
different frequency. As the "Shift" button, it allows you to send commands
9 thru 16 to the receiver.
To use as the "P" button, you must press and hold the button for
approximately 5 seconds to enter programming mode. (See
PROGRAMMING section for more details).
To use as the "Shift" button, press the P/Shift button momentarily. The TX
LED will begin to flash rapidly indicating you're in the Shift mode. While in
shift mode pressing buttons 1 thru 8 transmit the higher numbered code
for that button. The transmitter will stay in the Shift mode as long as
buttons are being depressed within 10 seconds of one another. During
this time, the TX LED gives visual confirmation that you're in Shift mode
by continuously flashing GREEN/RED rapidly. After 10 seconds has
elapsed with no buttons depressed, the transmitter will revert back to
standard mode and the TX LED will extinguish. If, while in Shift mode, you
wish to transmit a button 1 thru 8 command and don't want to wait for the
Shift mode to time out, you can simply press the P/Shift button
momentarily to revert back to the standard mode.
105 Bonnie Drive
Butler, PA 16002
724-283-4681
724-283-5939 (fax)
www.bwieagle.com
®
SR PLUS
MCQ-XBEE3
1846A-XBEE3
ETSI
PRODUCT INFORMATION
BULLETIN
Dimensions – 6.71" H x 3.27" W x 1.32" D
CONTROLS & INDICATORS
LED illuminates "RED" continuously while button is
depressed and unit is transmitting. When this LED
TX LED
blinks during a transmission, the battery needs to
be recharged.
Keypad
Transmit CH.1 thru 8 individual button RF codes to
Pushbuttons
the receiver
1 thru 8
The P/Shift button performs three functions:
1. If button is depressed momentarily and another
button is then pressed within 10 seconds, the
higher code for that button is transmitted. This
allows for transmission of pushbutton codes 9 thru
16.
Pushbutton
P/Shift
2. If button is depressed for longer than 5 seconds,
the transmitter will enter "programming" mode.
See PROGRAMMING section.
3. See "Battery Charge Status" for using P/shift to
see battery level.
Keypad
Transmit CH. 9 thru 16 individual button RF codes
Pushbuttons
to the receiver
9 thru 16