Related Manuals for Raycus RFL-A200D
Summary of Contents for Raycus RFL-A200D
- Page 1 Fiber Delivered Direct Diode RFL-A200D Laser User Guide （compact module） Wuhan Raycus Fiber Laser Technologies Co., Ltd...
- Page 2 WUHAN RAYCUS FIBER LASER TECHNOLOGIES CO. LTD. Safety Information Thank you for choosing Raycus Fiber Delivered Direct Diode laser. This User Guide provides important safety, operation, warranty and other information. Please read it carefully before you use this product. In order...
- Page 3 武汉锐科光纤激光技术股份有限公司 WUHAN RAYCUS FIBER LASER TECHNOLOGIES CO. LTD. WARNING: You must use appropriate laser safety eyewear when operating this device. The laser safety eyewear is selected according to the range of wavelengths emitted from this product. The end user must ensure that the laser safety eyewear used protects against light emitted by the device over its entire range of wavelengths.
- Page 4 武汉锐科光纤激光技术股份有限公司 WUHAN RAYCUS FIBER LASER TECHNOLOGIES CO. LTD. Optical Safety Any dust on the end of the collimator assembly can burn the lens and damage the laser. CAUTION: If the output of the device is delivered through a lens with an anti-reflection coating, make sure that the lens is of good quality and clean.
- Page 5 Unpacking and Inspection Your Raycus fiber delivered direct diode laser is shipped in a package designed to provide maximum protection. Upon delivery, please inspect all packaging for evidence of mishandling or damage. If you find any evidence...
- Page 6 A comprehensive packing list is included with the system documentation. Check all items against the list and contact Raycus immediately if there is any missing item or evident damage to the unit.
- Page 7 武汉锐科光纤激光技术股份有限公司 WUHAN RAYCUS FIBER LASER TECHNOLOGIES CO. LTD. d） Please inspect the output head carefully for dust or other contamination. Use appropriate lens paper to clean it if necessary. Do not touch the output lens at any time; e） Please cap the output head when it is not in use, and make sure the cap is clean;...
- Page 8 Figure1 and Figure2 show dimensions and Installation of the product. Figure 1 dimensions (unit: mm) Figure 2 Installation (unit: mm) Please leave a space as table 3 between Raycus fiber on every side for the necessary air circulating. Table 3 gap wanted (unit: mm)
- Page 9 OFF; d） Check the output head and clean it if necessary. This procedure must be performed by Raycus personnel or person authorized by Raycus. Make sure the environment is clean, or the output head may be contaminated. It is prohibited to use fan during installation, which will cause dust in the air;...
- Page 10 武汉锐科光纤激光技术股份有限公司 WUHAN RAYCUS FIBER LASER TECHNOLOGIES CO. LTD. Precautions for Product Fiber Delivered Direct Diode Lasers RFL-A200D adopts air cooled miniaturization design, which requires high heat dissipation. Users in different industries have different technology application plans when using lasers. According to the heat dissipation capacity of this laser, the recommended and restricted use conditions are given, as shown in Table 4 and Figure 3.
- Page 11 武汉锐科光纤激光技术股份有限公司 WUHAN RAYCUS FIBER LASER TECHNOLOGIES CO. LTD. Figure 3 Diagram of laser use area Using the Product Front Panel Figure 4 Front Panel View Power Cord ,USE M16 cable connector...
- Page 12 武汉锐科光纤激光技术股份有限公司 WUHAN RAYCUS FIBER LASER TECHNOLOGIES CO. LTD. Figure 5 The Power Cord of the Laser 1：+48V ；2：GND ；3：PE Laser output Status Leds PO: power led IN: interlock led SI: signal led LA: laser emit led LD: laser error led...
- Page 13 武汉锐科光纤激光技术股份有限公司 WUHAN RAYCUS FIBER LASER TECHNOLOGIES CO. LTD. 5V:external mode MODE_CHS input Control Mode select internal mode Ext_ADC input Analog Voltage Signal 0-10V 5V:enable Ext_Foot_EN input Foot pedal forbidden 7/19 EXT_+5V output always enable red light 5V:enable ③ Ext_Red_Always input...
- Page 14 武汉锐科光纤激光技术股份有限公司 WUHAN RAYCUS FIBER LASER TECHNOLOGIES CO. LTD. Figure 6 Rear Panel View cooling fans Control Modes There are two different modes of operation: external AD mode and RS232 mode. The following diagram shows the process of entering a certain control mode.
- Page 15 武汉锐科光纤激光技术股份有限公司 WUHAN RAYCUS FIBER LASER TECHNOLOGIES CO. LTD. to be set AD signal according to output power. Wiring in AD Mode Figure 8 Wiring Diagram in AD mode CW mode wave diagram Figure 9 CW mode wave 3.4.1.2 Pulse mode In this mode, the laser emissions under modulation, so set parameters including Ext_MOD, EXT_Laser_EN and EXT_AD to switch on laser emission.
- Page 16 武汉锐科光纤激光技术股份有限公司 WUHAN RAYCUS FIBER LASER TECHNOLOGIES CO. LTD. Pulse mode wave diagram Figure 10 Pulse mode wave 3.4.2 RS232 Mode RS-232 mode is a remote control mode. In this mode, we have a protocol for communication between the laser and the upper computer, and you can set emission parameters and get information from the laser.
- Page 17 武汉锐科光纤激光技术股份有限公司 WUHAN RAYCUS FIBER LASER TECHNOLOGIES CO. LTD. and time can be set in preset mode. Communication Protocol: Table 7 The Communication Protocol for RS-232 Mode (HEX) function header code data tail Response Get working 00,00,00,01 D1 02 00 X X F0...
- Page 18 武汉锐科光纤激光技术股份有限公司 WUHAN RAYCUS FIBER LASER TECHNOLOGIES CO. LTD. Enable red light 0,0,0,X EB X F0 Set group number in 0,0,0,X E3 X F0 preset mode get group number in 0,0,0,0 E4 X F0 preset mode Set group number in 0,0,0,X...
- Page 19 The warranties start on the date of shipment from Raycus for a period of time asset forth in the applicable purchase contracts or product specifications.
- Page 20 All service and maintenance shall be performed by qualified Raycus personnel. Please contact Raycus as soon as possible when problems under warranty about maintenance happened to the product. The product returned with permission should be placed in a suitable container.
Need help?
Do you have a question about the RFL-A200D and is the answer not in the manual?
Questions and answers