Table of Contents
Related Manuals for Raycus RFL-A500D
Summary of Contents for Raycus RFL-A500D
- Page 1 版本号 密级 内部 阶段 标记 RFL-A500D～2000D 会签 光纤输出半导体激光器英文说明书 钟磊 RFL-A500D～2000D·JS02 黄文娟 部 门 半导体激光器技术研究部 编 写 曾 诚 20201222 校 对 李 辉 20210105 受 控 审 核 刘 超 20210106 武汉锐科 标 审 李其军 20210118 批 准 胡慧璇 20210120 旧底图登记号...
- Page 2 受 控 武汉锐科 Fiber Delivered Direct Diode Lasers User Guide RFL-A500D～2000D...
-
Page 3: Table Of Contents
受 控 Wuxi Raycus Fiber Laser Technologies Co., Ltd. User Guide of Raycus 500W～2000W laser 武汉锐科 TABLE OF CONTENTS 1 Safety Information........................3 1.1 Symbols Used in This User Guide..................3 1.2 Laser Classification......................3 1.3 Safety Labels........................4 1.4 Optical Safety........................5 1.5 Electrical Safety.........................5... - Page 4 受 控 Wuxi Raycus Fiber Laser Technologies Co., Ltd. User Guide of Raycus 500W～2000W laser 武汉锐科 4.5 Operating Process......................24 4.6 Selection of Control Mode....................24 4.7 Pilot Light to Control.......................32 4.8 Steps of Shutting Down....................32 5 Alarms and Solutions....................... 32 5.1 Alarms Display........................
-
Page 5: Safety Information
武汉锐科 1 Safety Information Thank you for choosing Wuxi Raycus Fiber Delivered Direct Diode laser. This User Guide provides important safety, operation, warranty and other information. Please read it carefully before you use this product. In order to ensure safe operation and optimal performance of the product, please follow the warnings, cautions, operating procedures and other instructions accordingly. -
Page 6: Safety Labels
受 控 Wuxi Raycus Fiber Laser Technologies Co., Ltd. User Guide of Raycus 500W～2000W laser 武汉锐科 1.3 Safety Labels Figure1Top View and Back View Figure 1 shows the product safety labels and its location.These safety signs include: safety warnings, laser output head warnings, product nameplates, etc.The safety identification details... -
Page 7: Optical Safety
受 控 Wuxi Raycus Fiber Laser Technologies Co., Ltd. User Guide of Raycus 500W～2000W laser 武汉锐科 7) Electrical Hazard Label 1.4 Optical Safety Any dust on the end of the collimator assembly can burn the lens and damage the laser. -
Page 8: Product Description
User Guide of Raycus 500W～2000W laser 武汉锐科 d） There are no operator serviceable parts inside, and all maintenance must be performedin Raycus or by qualified Raycuspersonnel. Do not try to remove covers, or electrical shock maybe caused, and warranty will be void. 2 Product Description 2.1 Features... -
Page 9: Package Contents
Please refer to the packing list accompanying the shipment to check actual items included. 2.4 Unpacking and Inspection Raycus ensure that the laser do get adequate protection by special designed packaging material and box during the transit. Even so, In order to prevent the unpredictable component damage, users need to scrutinize the packing box is right before unpacking it whether or not cracking, abrasion, dampened and other phenomena. -
Page 10: Operation Environment
受 控 Wuxi Raycus Fiber Laser Technologies Co., Ltd. User Guide of Raycus 500W～2000W laser 武汉锐科 On unwrapping the box, Please check that packing lists and physical goods are the same. If you have any questions, feel free to contact any of us at any time. -
Page 11: Specifications
受 控 Wuxi Raycus Fiber Laser Technologies Co., Ltd. User Guide of Raycus 500W～2000W laser 武汉锐科 Table 4The Constant Dew Point Table AMBIENT DEW POINT Maximum Relative Humidity Ambient Temperature(℃) 20% 30% 40% 50% 60% 70% -3.5 14.5 10.5 16.5 10.5... -
Page 12: Properties Of Products
受 控 Wuxi Raycus Fiber Laser Technologies Co., Ltd. User Guide of Raycus 500W～2000W laser 武汉锐科 f） The high temperature laser in summer is easy to produce dew and cause permanent damage. Please make sure that the water cooling machine stops at the same time when the laser stops. -
Page 13: Installation
受 控 Wuxi Raycus Fiber Laser Technologies Co., Ltd. User Guide of Raycus 500W～2000W laser 武汉锐科 Electrical Parameters single phase 220VAC±10% three phase 380VAC±10% Power Supply 50/60Hz 50/60Hz TN-C Control Mode RS-232/AD Other Parameters Dimensions(W×H×D)（mm） 485×237×679 485×237×765 Weight(kg) ＜50 Operating Ambient Temperature (℃) 10～40... -
Page 14: Output Head And Installation
受 控 Wuxi Raycus Fiber Laser Technologies Co., Ltd. User Guide of Raycus 500W～2000W laser 武汉锐科 Figure 3a) Top View of 500W/1000W Laser (unit: mm) Figure 3 Top View of 1500WLaser and 2000WLaser(unit: mm) 3.2 Output Head and Installation Figure 4 shows QBH Output Head：... -
Page 15: Cooling Requirements
受 控 Wuxi Raycus Fiber Laser Technologies Co., Ltd. User Guide of Raycus 500W～2000W laser 武汉锐科 Figure 4RFL-QBH Output Head(unit: mm) Inspect the output lens before installing the output head to the processing head. wipe the output lens with absolute alcohol if it is unclean. - Page 16 受 控 Wuxi Raycus Fiber Laser Technologies Co., Ltd. User Guide of Raycus 500W～2000W laser 武汉锐科 a） The water temperature setting of cooling system: 1） summer（Ambient temperature is higher than 30℃）25±0.5℃； 2） winter（Ambient humidity temperature is lower than 30℃）22±0.5℃。 b） Coolant requirements：...
-
Page 17: Installation Procedure
Insert the water pipes into the inlet and outlet; e） Check the output head and clean it if necessary. This procedure must be performed byRaycus personnel or person authorized by Raycus. Make sure the environment is clean, or theoutput cable may be contaminated. -
Page 18: Using The Product
User Guide of Raycus 500W～2000W laser 武汉锐科 4 Using the Product Raycus CW fiber laser has stopped using theHyperTerminal, so the HyperTerminal will notworkwhen thelaser is powered on. Please clip the address below to downloadthe latest PC software and the relevant manual. -
Page 19: Power Connection
④ SERVICE: The laser switch and security interlocking interface ⑤ AC INPUT: AC in connector, mustuse the plug offered by Raycus. ⑥ POWER: Air switch, that open or close the electric circuit. WATER IN/OUT: Water pipe connectors, the inlet and outlet for cooling water to flow in ⑦... -
Page 20: Interface Definitions
受 控 Wuxi Raycus Fiber Laser Technologies Co., Ltd. User Guide of Raycus 500W～2000W laser 武汉锐科 One end of the power cord is a plug, insert it into the socket 'AC INPUT' onthe rear panel. 500W and 1000W lasers’power line consist of three lines,L,N and PE, Connected to the 220VAC. - Page 21 User Guide of Raycus 500W～2000W laser 武汉锐科 Figure 8 Modulation Input Raycus provide MOD Cable, as shown in figure 9. Figure 9 MOD Cable-The Cable for Modulation Signal The modulation signal cable core is positive (24V) and the external metal mesh is negative (GND).
- Page 22 受 控 Wuxi Raycus Fiber Laser Technologies Co., Ltd. User Guide of Raycus 500W～2000W laser 武汉锐科 The internal circuit of the modulation signal is shown in figure 10. Figure 10 The Internal Circuit of The Modulation Signal 4.4.3 Control Interface The pin number of‘CTRL-INTERFACE’is shown in figure 13...
- Page 23 受 控 Wuxi Raycus Fiber Laser Technologies Co., Ltd. User Guide of Raycus 500W～2000W laser 武汉锐科 ＜100mA Laser Ready Output Ready signal EX_GND Reference6,7,8,20,24GND 24V（power for PIN8 and PIN24） EX_VCC Input ＜500mA Analog Input Analog Voltage Signal 0V~10V ＞10mA Laser Power Output Power indication 0V~3.8V...
- Page 24 受 控 Wuxi Raycus Fiber Laser Technologies Co., Ltd. User Guide of Raycus 500W～2000W laser 武汉锐科 Figure 13 PIN8 and PIN24 internal circuit 4.4.4 RS-232 Serial Port Figure 14 shows the pin number of RS-232 serial port: Figure 14Pin Number of RS-232 Serial Port...
-
Page 25: Work Patterns And Control Modes
Turn on the Air switch is on, release red emergency stop button. d） Open the key switch, start the laser. 4.7 Selection of Control Mode Raycus provide assorted upper computer software, as shown in Figure 17(Download theRaycus software and software manual, please log in to Raycus official website). - Page 26 受 控 Wuxi Raycus Fiber Laser Technologies Co., Ltd. User Guide of Raycus 500W～2000W laser 武汉锐科 Figure 15The Function Area of Upper Computer Software Table11 Brief Description of Each Functional Area Functional Area Description ‘Ready’——The laser complete ‘Laser EN’——Enable Signal Laser Indicators ‘Emission’——The laser is emitting laser...
- Page 27 受 控 Wuxi Raycus Fiber Laser Technologies Co., Ltd. User Guide of Raycus 500W～2000W laser 武汉锐科 Set parameters: Laser Power, Frequency, Duty Ratio ‘Set’——After Setting parameter, Need to click ‘set’ Laser Control “Emission on”——Pressing the button, the laser is emitting laser; button is unavailable, the laser is being shut down.
- Page 28 受 控 Wuxi Raycus Fiber Laser Technologies Co., Ltd. User Guide of Raycus 500W～2000W laser 武汉锐科 4.7.2 External RS232 ModeOperation Procedure a） Turn key switch anti-clockwise to ‘REM’ position (or turn key switch to ‘OFF’, Short-circuit PIN1 and PIN2 in ‘SERVICE’ port. Then ‘Power’ indicator light is on.
- Page 29 受 控 Wuxi Raycus Fiber Laser Technologies Co., Ltd. User Guide of Raycus 500W～2000W laser 武汉锐科 Figure 18Control Sequence Diagram of PLUSE Pattern in External Control RS232 Mode...
- Page 30 受 控 Wuxi Raycus Fiber Laser Technologies Co., Ltd. User Guide of Raycus 500W～2000W laser 武汉锐科 4.7.4 Wiring in External Control AD mode Figure 19 Wiring In External Control ADMode 4.7.5 The Operation Procedure of External AD mode a） When PIN 7 and PIN 9 of the DB25 control interface is applied to 24V, the laser enters the externalAD mode.
- Page 31 受 控 Wuxi Raycus Fiber Laser Technologies Co., Ltd. User Guide of Raycus 500W～2000W laser 武汉锐科 d） The power of the laser is controlled by the voltage obtained by PIN 22 and PIN 25 of theDB25 interface connector. e） The external MOD interface provides modulating signal for the laser.
- Page 32 受 控 Wuxi Raycus Fiber Laser Technologies Co., Ltd. User Guide of Raycus 500W～2000W laser 武汉锐科 Figure 21 Wiring in Internal Control Mode 4.7.8 The Operation Procedure ofInternal Control Mode a） Turn key switchto ‘ON’ position. Then ‘Power’ indicator light is on.
-
Page 33: Pilotlight To Control
受 控 Wuxi Raycus Fiber Laser Technologies Co., Ltd. User Guide of Raycus 500W～2000W laser 武汉锐科 Figure 23 Control Sequence Diagram of PulseMod in Internal Control Mode 4.8 PilotLight to Control Connect to AC power, Both ‘ POWER’ green indicator light and the laser generate pilot light are on. -
Page 34: Alarm Solutions
Laser On Button Alarm Solution: Please power off and release the “LASER” button. Repower and check if the alarm is resolve. If this alarm continues to occur, please contact Raycus. Instruction: Occurs when the InterLock is disconnected. InterLock Alarm Solution: Short-circuit the interLock pins and restart the laser to try. -
Page 35: Warranty, Return And Maintenance
Raycus warrants that all Raycus fiber laser products are conformed to applicable productspecifications under normal use and are free from defects in materials and workmanship. Thewarranties start on the date of shipment from Raycus for a period of time as set forth in theapplicable purchase contracts or product specifications. -
Page 36: Service And Repair
User Guide of Raycus 500W～2000W laser 武汉锐科 who are notfrom Raycus due to excessive use or not following the instructions. Customer has theresponsibility to understand and follow this instruction to use the device. Any damage caused byfault operating is not warranted. Accessories and fiber connectors are excluded from thiswarranty.