Download Print this page
Extron electronics Decora Style1-Gang Wallplate WP CTL D Installation Manual
Extron electronics Decora Style1-Gang Wallplate WP CTL D Installation Manual

Extron electronics Decora Style1-Gang Wallplate WP CTL D Installation Manual

Extron electronics decora style 1-gang wallplate installation guide

Advertisement

Quick Links

WP CTL D Installation Guide
The Extron WP CTL D is a Decora style 1-gang wall plate which passes RS-232 control signals
from a computer or control system, and IR signals from an IR source.
Install it directly into the wall using a mud ring, or in a 1-gang junction box (not supplied),
following the steps below.
1.
Using a mud ring or a junction box as a guide, mark the holes and cut out the
material within the marked area.
N If installing a junction box, allow enough depth for
the wall plate and cables.
The box should be at least 2.0" (5.1 cm) deep to
accommodate the connectors, plate, and cables.
2.
Either
• Insert the mud ring into the opening, rotate
the dog legs, and secure with the screws provided,
or
• Insert the wall box and secure with 10-penny nails
or screws.
3.
Run the RS-232 and IR signal cables behind the wall
and thread them through the mud ring or wall box.
N Extron recommends using a good quality, low
capacitance, shielded cable such as an Extron
CTL or SPL Control cable.
WP CTL D Installation Guide, cont'd
4.
Connect the IR cable to the rear panel IR
connector by inserting the signal wire into
the hole marked "S" , and the ground wire
into the hole marked "G" (see inset, step 4).
N The recommended driving distance from
an MLC controller is 100 feet.
5.
Connect the RS-232 cable to the rear panel RS-232
connector by inserting the ground wire into the hole
marked "G", the transmit wire into the hole marked
"Tx", and the receive wire into the hole marked
"Rx" (see inset, step 5).
6.
Mount the device into the mud ring or wall box.
7.
Attach the supplied Decora faceplate.
N If applicable, repeat steps 1-7 to install additional wall plates.
8. Connect the RS-232 control device and/or IR input device to the front of the WP CTL D.
Extron USA - West
Extron USA - East
Headquarters
+800.633.9876
+800.633.9876
Inside USA / Canada Only
Inside USA / Canada Only
+1.919.863.1794
+1.714.491.1500
+1.919.863.1797 FAX
+1.714.491.1517 FAX
G S
Extron Europe
Extron Asia
Extron Japan
+800.3987.6673
+800.7339.8766
+81.3.3511.7655
Inside Europe Only
Inside Asia Only
+81.3.3511.7656 FAX
+31.33.453.4040
+65.6383.4400
+31.33.453.4050 FAX
+65.6383.4664 FAX
Wall
Wall Mounting
Bracket
G
S
IR
G
R x
T x
ri a
l
S e
Extron
WP CTL D
G = Ground
S = Signal (IR)
White striped wire
100'
(30.5 m)
WP CTL D
IR Out
Step 4
Step 5
Extron China
Extron Dubai
+400.883.1568
+971.4.2991800
Inside China Only
+971.4.2991880 FAX
+86.21.3760.1568
+86.21.3760.1566 FAX
Decora
Faceplate
IR Emitter
68-1618-01
Rev B 08 08

Advertisement

loading
Need help?

Need help?

Do you have a question about the Decora Style1-Gang Wallplate WP CTL D and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

This manual is also suitable for:

Wp ctl d