Advertisement
Quick Links
instructions
murano dresser/changer
FR012DC: V3/07/06
© Mamas & Papas (Holdings) Ltd. 2006
IMPORTANT: Please read instructions carefully
and keep for future reference
PDF compression, OCR, web optimization using a watermarked evaluation copy of CVISION PDFCompressor
– 1 –
Advertisement
Related Manuals for Mamas & Papas murano dresser/changer
Summary of Contents for Mamas & Papas murano dresser/changer
- Page 1 FR012DC: V3/07/06 © Mamas & Papas (Holdings) Ltd. 2006 IMPORTANT: Please read instructions carefully and keep for future reference PDF compression, OCR, web optimization using a watermarked evaluation copy of CVISION PDFCompressor – 1 –...
-
Page 2: Main Components
MURANO DRESSER/CHANGER THESE INSTRUCTIONS ARE IMPORTANT. PLEASE READ THEM CAREFULLY AND RETAIN FOR FUTURE REFERENCE. Before assembling your dresser/changer... Unpack all wooden components / fittings and identify them against the fittings and components lists. Do not discard any packaging until you are certain you have all the correct panels and fittings. - Page 3 FITTINGS x 33 x 12 Wooden dowels Drawer cams x 25 x 12 Cam studs Long screws Handle screws Handle spacers x 18 Drawer handles Short screws Drawer runners Plastic feet x 12 Euro screws Carcass runners x 13 x 32 Carcass cams Nails Blanking bolts...
- Page 4 Insert four dowels (A) into the ends of a left drawer side (1) and a right drawer side (2). You may need to use a light hammer to gently knock them fully into position. Slot four drawer cams (B) into the large holes in the inside faces of both of the drawer sides.
- Page 5 Screw four cam studs (C) into the holes in the inside of one of the drawer fronts (3), see diagram. Tighten them using a cross-head screwdriver. Attach the left an right drawer sides (1&2) to the drawer front. Align the dowels in the drawer sides and the cam studs in the drawer front with the relevant...
- Page 6 Slot a drawer base (4) into the grooves in the drawer sides. Ensure that the drawer base is fully inserted into the groove in drawer front. Fix a drawer back (5) to the drawer sides. Ensure that the groove in the drawer back is aligned with the grooves in the drawer sides and slot the components...
- Page 7 Attach the drawer handle to the drawer front by inserting two handle screws (E) through the holes in the drawer front, see diagram. Slot two handle spacers (F) onto the threaded ends of the handle screws. Align the ends of the handle screws with the holes in the drawer handle (G) and slot them...
- Page 8 Slot the lugs on the four plastic feet (J) into the holes in the bottom edges of the left side panel (6) and the right side panel (7). You may need to use a light hammer to fully insert the plastic feet. Insert four dowels (A) into the holes in the top edges of the left and...
- Page 9 Attach the six carcass runners (K) to the inside faces of the left and right side panels (6&7). When fitted the wheel on the carcass runners must point towards the front of the dresser, away from the recesses in the back edges of the side panels.
- Page 10 Slot four carcass cams (M) into the large holes in the inside faces of both of the left and right side panels (6&7). Note: carcass cams have a narrower head than the drawer cams (B) supplied in the fittings pack. Ensure that the arrow on the heads of the carcass cams point towards the...
- Page 11 Slot four carcass cams (M) into the large holes in the bottom rails (8). Ensure that the arrow on the heads of the carcass cams point towards the connecting holes. Lay the right side panel (7) flat on a clean, level work surface and slot the bottom rails (8) onto it, see diagram.
- Page 12 Carefully turn the assembled components over, so that the front edge of the dresser carcass faces down, see diagram. Align the cam studs in the left side panel (6) and the dowels in the bottom rails with the relevant holes and slot them together.
- Page 13 Position the top (9) so that the groove in the underside is aligned with the recesses in the back edges of the side panels. Align the cam studs in the top and the dowels in the side panels with the relevant holes and slot them together.
- Page 14 Before fixing the back panels to the dresser you will need to check that it is square. To do this, measure from the bottom corner of one side panel to the top corner of the opposite, A to A, see diagram. Now measure the opposite diagonal, B to B.
- Page 15 Note: If the dresser/ changer is not to be used as a baby changer you may omit fitting the changer rails to the top. For instructions on completing the construction of the baby changing unit go to Step 26. With the help of another person, lift the dresser upright.
- Page 16 Important Safety Notice - Use as Baby Changing Unit If you wish to use your Murano Dresser/Changer as a baby changing unit, the all changing rails MUST be fitted to the top (see steps 25 and 30 below). Unscrew the four...
- Page 17 Screw two cam studs (C) into the holes in the inside faces of the left changing rail (15) and the right changing rail (16), see diagram. Screw three cam studs into the holes in the inside face of the back changing rail (13) Tighten the cam studs using a cross-head...
- Page 18 Slot three carcass cams (M) into the large holes in the underside of the top back section (12). Note: Carcass cams have a narrower head than the drawer cams (B) supplied in the fittings pack. Tighten the carcass cams using a flat-head screwdriver.
- Page 19 Align the runners on the drawers with the runners on the dresser sides and slide them in. The dresser is now finished and ready for use. Ensure that all fittings are correctly tightened before use. WALL STRAP INFORMATION The wall strap is only intended to be used with the Mamas and Papas product that it is supplied with.
- Page 20 • A changing mattress is not supplied with this product. We recommend that you only use a Mamas & Papas changing mattress with the Murano Dresser/Changer. Lay the changing mattress on the changing surface, within the retaining rails.