Advertisement
Quick Links
WM342-KD Series Installation Guide
• One WM342-KD330/WM342-KD331 system unit
• 1 SATA data cable
• 1 CPU cooler and 1 system fan
• HDD mounting screws
• 1 Quick Installation Guide
• 1 CD disk includes:
- Drivers / Manual
Front View
Rear View (WM342-KD330/WM342-KD331)
Power Button
SATA
Drive Bay
DFI reserves the right to change the specifications at any time prior to the product's release. For the latest revision and for a more
details of the installation process, please refer to the user's manual on the website.
All manuals and user guides at all-guides.com
Package Contents
Panel
Power LED (green)
HDD LED (red)
LAN 1 LAN 2
PS/2 KB/MS
USB 3.0 1-4
USB 2.0 1-2
COM1
VGA
DVI-D
(DVI-I connector)
DP++
www.dfi.com
1
Expansion Slot
AC Power
for KD331:
Socket
LAN 3
LAN 4
or
for KD330:
Line-out
Mic-in
Advertisement
Related Manuals for DFI WM342-KD Series
Summary of Contents for DFI WM342-KD Series
- Page 1 Line-out Mic-in DFI reserves the right to change the specifications at any time prior to the product's release. For the latest revision and for a more details of the installation process, please refer to the user's manual on the website.
-
Page 2: Opening The Chassis
All manuals and user guides at all-guides.com Opening the Chassis Please observe the following guidelines and follow the procedure to open the system. 1. Make sure the system and all other peripheral devices connected to it have been powered off. 2. -
Page 3: Installing A Dimm
All manuals and user guides at all-guides.com Installing a DIMM 1. Align the notch on the DIMM with the tab in the DIMM connector. 2. Press down on the DIMM until the release tabs spring back to secure the DIMM in place. The installed DIMM Notes: The WM342-KD330 is equipped with two or four DDR4 (dual channel) sockets depending... - Page 4 All manuals and user guides at all-guides.com Installing 2.5" SATA Drive The system can accommodate two 2.5" SATA installation. Use the following proce- dure to install a SATA drive onto the system. 1. Remove the thumb screws that secure the HDD drive bay to the chassis and remove the drive bay.
- Page 5 All manuals and user guides at all-guides.com 2. Secure the hard drive to the drive bay. Align the mounting holes on the SATA drive with the mounting holes on the HDD drive bay. Use 4 mounting screws to install the hard drive onto the HDD drive bay. Drive bay Mounting screw 2.5"...
- Page 6 All manuals and user guides at all-guides.com 3. Slide the HDD drive bay back to the system and secure it with the thumb screws. 4. Connect the SATA data cable and power cable to the connectors on the SATA drive. And connect the other end of the SATA data cable on the motherboard.
- Page 7 All manuals and user guides at all-guides.com Installing a PCI or PCIe Expansion Card Use the following procedure to install a PCIe expansion card: 1. Remove the mounting screws to uninstall the card slot bracket. Card slot bracket Screw 2. Insert the expansion card in the connector on the motherboard and press down until secured.
- Page 8 All manuals and user guides at all-guides.com 3. Reinstall the card slot bracket to secure the expansion card in place. Rear View PCIe card Notes: The WM342-KD330 is equipped with one PCIe x16 and one PCI slots. The WM342-KD331 is equipped with one PCIe x16 and one PCIe x4 slots.
-
Page 9: Installing An M.2 Card
All manuals and user guides at all-guides.com Installing an M.2 Card The system is equipped with one M.2 socket, supporting both the M.2 22x60mm and 22x80mm (key M) form factors. Use the following procedure to install an M.2 card: 1. To install an M.2 type 2260 card, please install the standoff at the 60mm mounting position first. -
Page 10: Installing A Mini Pcie Card
All manuals and user guides at all-guides.com Installing a Mini PCIe Card The system board is equipped with one Mini PCIe slot that uses USB, PCI and mSATA signals. 1. Grasp the Mini PCIe card by its edges and align the notch in the connector of the PCIe card with the notch in the connector on the system board. - Page 11 All manuals and user guides at all-guides.com Board Layout and Jumper Settings (WM342-KD330) COM 1 (DDR4_2, DDR4_4 for KD330-Q170 only) RS232/422/485 DDR4_2 DDR4_4 Select (JP7) DDR4_1 DDR4_3 PS/2 KB/MS COM 1 RS232/Power Select (JP9) USB 5-6 System Fan 1 CPU Fan COM 1 USB 2.0 RS232/422/485...
- Page 12 3-5, 4-6 On Notes: 1. When COM 1 RS232/422/485 is selected, JP8 and JP10 must be set in accordance to JP7. 2. When COM 2 RS232/422/485 is selected, JP12 and JP13 must be set in accordance to JP11. www.dfi.com A51401837...