ADJ WIFLY NE1 User Manual page 16

O P E R AT I O N
Firmware Version
Note:This is a read only menu option that will display the con- trollers current software version.
1. Press the SET-UP button for two seconds to enter the main menu.
2. Turn the DIAL/ENTER dial to menu option 16 (Firmware Ver- sion). Press the DIAL/ENTER dial to
enter. Press the ESC/PAGE button to exit.
Fixture Control, Saving, & Playing Memories
Note: Although the generic profiles may work for you, it is rec- ommended that you load and use the
custom profiles that were provided on the USB sitck that was included with your control- ler. The custom
profiles may offer you additional control and features that the generic profiles do not include. If you
wish to use the custom profiles, please refer to the LOADING FIXTURE PROFILES section of this user
manual and load them before proceeding. After you have patched your fixtures, you can con- trol and
save memories using the following steps.
1. Press the FIXTURE button then select the fixtures, using the FUNCTION 1-12 buttons, that you
want to control. If you are using multiple fixtures of the same type and want to control them at the
same time, you can press the first and last buttons so all fixtures in between are selected at the
same time. For ex- ample, I have patched 6 fixtures on buttons 1-6, to select them all quickly, I would
simultaneously press buttons 1 & 6 so all 6 fixtures are selected.
2. Press the COLOR button and add a color by using the FUNCTION 1-12 buttons. Turn the DIAL/
ENTER dial to switch between two pages of preset colors (Note: your fixture must support this
feature to function).
3. Press the GOBO button and add a gobo by using the FUNCTION 1-12 buttons. Turn the DIAL/
ENTER dial to switch between two pages of preset gobos (Note: your fixture must sup- port this
feature to function).
4. Press the EFFECT button and add an effect by using the FUNCTION 1-12 buttons. Turn the DIAL/
ENTER dial to switch between three pages of effects. In the display, you will see ML EFFECT (for
moving lights) and RGB EFFECT 1 and RGB EFFECT 2 (for RGBWA+UV LED's) plus the speed,
phase, size, and direction settings, which can be controlled from the four EFFECT rotary dials. You
can pause an effect at any time by pressing the PAUSE button. (Note: your fixture must support this
feature to function).
5. Press the SHOW button and enable a show by using the FUNCTION 1-12 buttons. (Note: your
fixture must support this feature to function).
6. You can also set all channel values manually. If you have already set your scene and want to
store it. please see step 7 now. To make manual channel adjustments, press the FIXTURE button,
then press the DIAL/ENTER dial for two seconds, the display will list channels 1-4 along with their
current values. Use the four EFFECT dials to adjust each channel listed in the display. Channels are
displayed four at a time. To access additional channels, turn the DIAL/ENTER dial clockwise and
counter-clockwise
7. To save your current output, press and hold down any of the six MEMORY buttons until the display
reads "Operation Complete!". Press that same MEMORY button a second time to playback from that
memory location, it should illuminate solid green. Repeat steps 1-6 to store additional memories.
There are two memory banks. To access the secondary memory bank press the ESC/PAGE button.
If there is a memory running, that MEMORY button will flash letting you know that is actively running
in the other bank. If your memory includes an "EFFECT", you can pause the effect by pressing the
PAUSE button.
8. You can trigger the STROBE button at any time during play- back. The STROBE button will function
relative to the STROBE RATE fader setting. Adjusting your STROBE RATE fader will give you DMX
control over your fixtures shutter or RGBWA+UV channels. This function cannot be stored into a
memory.
9. You can manually adjust the MASTER DIMMER fader at any time during playback to set the overall
intensity for you active fixtures. This function cannot be stored into a memory.
16