CHIEF F-Series Steel Stud FSA1018 Installation Instructions Manual

F-series steel stud installation kit

Advertisement

Quick Links

I N S T A L L A T I O N I N S T R U C T I O N S
Instrucciones de instalación
Installationsanleitung
Instruções de Instalação
F-Series Steel Stud Installation Kit
Istruzioni di installazione
Installatie-instructies
Instructions d´installation
Spanish Product Description
German Product Description
Portuguese Product Description
Italian Product Description
Dutch Product Description
French Product Description
FSA1018

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the F-Series Steel Stud FSA1018 and is the answer not in the manual?

Questions and answers

Summary of Contents for CHIEF F-Series Steel Stud FSA1018

  • Page 1 I N S T A L L A T I O N I N S T R U C T I O N S Instrucciones de instalación Installationsanleitung Instruções de Instalação F-Series Steel Stud Installation Kit Istruzioni di installazione Installatie-instructies Instructions d´installation Spanish Product Description German Product Description...
  • Page 2: Installation Instructions

    FSA1018 DISCLAIMER Milestone AV Technologies, Inc., and its affiliated corporations and subsidiaries (collectively, "Milestone"), intend to make this manual accurate and complete. However, Milestone makes no claim that the information contained herein covers all details, conditions or variations, nor does it provide for every possible contingency in connection with the installation or use of this product.
  • Page 3 Installation Instructions FSA1018 TOOLS REQUIRED FOR INSTALLATION AND PARTS 1/2" (Ø13mm) (3/16") A (1) B (1) C (1) D (1) J (4) E (1) F (1) K (3) L (3) (1/4"-20) G (1) (1/4"-20 X 1 3/4") M (3) (1/4"-20 SNAPTOGGLE BB) H (1) (1/4"-20) N (1)
  • Page 4: Site Requirements

    FSA1018 Site Requirements WARNING: IMPROPER INSTALLATION CAN LEAD TO EQUIPMENT FALLING CAUSING SERIOUS PERSONAL INJURY OR DAMAGE TO EQUIPMENT! The figure below identifies the minimum reguirements for installation of display mounts onto a steel stud structure. If the structure or its components do not meet these requirements contact the mount manufacturer for specific instructions before attempting installation.
  • Page 5 Installation Instructions Preparation of Existing Mount If mount has previously been installed: Remove display from mount following instructions provided with mount. Remove mount from wall following instructions provided with mount. Proceed to step 4. If mount has not previously been installed: Remove mount wall plate from swing arm assembly by removing screw, washers and spacers, pivot pin and locknut.
  • Page 6: Mount Installation

    FSA1018 Mount Installation After determining the site meets the installation requirements: Identify desired mounting location on wall. Using a stud finder or similar method locate studs. Align mounting holes in mount with studs making sure mounting holes are centered on studs. Mark location of three mounting holes on wall.
  • Page 7 Installation Instructions Steel Stud Drywall Plastic Cap Plastic Straps Anchor Metal Channel SIDE VIEW Figure 7 11. Place mount over anchors and align mounting holes in display mount with holes in anchors. (See Figure 8) 12. Place flat washer (K) onto button head capscrew (L). 13.
  • Page 8 FSA1018 Chief Manufacturing, a division of Milestone AV Technologies, Inc. 8804-000347 RevC 2008 Milestone AV Technologies www.chiefmfg.com 06/08 USA/International A 8401 Eagle Creek Parkway, Savage, MN 55378 P 800.582.6480 / 952.894.6280 F 877.894.6918 / 952.894.6918 Europe A Fellenoord 130 5611 ZB EINDHOVEN, The Netherlands...

This manual is also suitable for:

Fsr seriesPsmh2685

Table of Contents