Related Manuals for Motorline professional MCS01
Summary of Contents for Motorline professional MCS01
- Page 1 MCS01 MCS01 USER/INSTALLER MANUAL MCS01 PUL1 PUL2 DET1 DET2 v1.0 REV. 05/2021...
-
Page 2: Table Of Contents
00. CONTENT 01. SAFETY INSTRUCTIONS INDEX ATTENTION: 01. SAFETY INSTRUCTIONS This product is certified in accordance with European 02. THE PRODUCT Community (EC) safety standards. TECHNICAL SPECIFICATIONS This product complies with Directive 2011/65/EU of the LEDs | BUTTONS | CONNECTORS European Parliament and of the Council, of 8 June 2011, on CONNECTIONS PROGRAMMING MODE... - Page 3 01. SAFETY INSTRUCTIONS GENERAL WARNINGS the motorized door or gate from being triggered involuntarily. • This manual contains very important safety and usage information. WARNINGS FOR TECHNICIANS very important. Read all instructions carefully before beginning the installation/usage procedures and keep this manual in a safe place •...
- Page 4 01. SAFETY INSTRUCTIONS • Attach the permanent label for the manual release as close as possible or maintenance! to the release mechanism. • Safety norms are not followed in the installation, use and • Disconnect means, such as a switch or circuit breaker on the electrical maintenance of the product.
- Page 5 TECHNICAL SPECIFICATIONS LEDs | BUTTONS | CONNECTORS MCS01 is a module it allows to control 2 traffic lights of 2 or 3 colors, the perfect solution for places LED LEGEND S1 • 3 LEDs Traffic light 1 (indicate the status of traffic light 1) with excessive traffic, places with poor visibility, garages with entry and exit through the same access, S2 •...
-
Page 6: Connections 4B
02. THE PRODUCT 03. CONFIGURATION CONNECTIONS FUNCTION CHART MAX. MIN. FACTORY MENU STATUS Traffic light 1 Traffic light 2 PROGRAMMABLE VALUE connections connections Adjust time of the green color - traffic light 2 PUL1 PUL2 DET1 DET2 Adjust time of the yellow color - traffic light 2 min. -
Page 7: Connections Scheme
24V traffic light, it is necessary to use an external power supply. MCS01 Traffic lights power supply is independent of MCS01 TRAFFIC LIGHT 2 power supply. TRAFFIC 1 MC50 - Suggested use PUL1 PUL2 DET1 DET2... -
Page 8: Functions 7B
GREEN COLOR TIME SET OF THE TRAFFIC LIGHT 1 The MCS01 module works with two or three color traffic lights. Allows you to choose the polarities of the This menu allows to configure the time that the green color of traffic light 1 will be ON during its operation. -
Page 9: Red Color Time Setting Of The Traffic Light 2
03. CONFIGURATION 03. CONFIGURATION DET 2 TIME SETTING RED COLOR TIME SETTING OF THE TRAFFIC LIGHT 2 This menu allows to configure the time that the red color of traffic light 2 will be on, during its operation. This menu allows to configure the time that DET2 has to be blocked to validate a detection. The double detection setting (DET and PUL) will determine the time you have to activate the PUL2 input after passing DET2. -
Page 10: Define Maximum Vehicle Capacity 9A
03. CONFIGURATION 03. CONFIGURATION DEFINE MAXIMUM VEHICLE CAPACITY REMOVE ALL REMOTE CONTROLS This menu allows to configure the maximum vehicle capacity inside the park. This menu allows you to delete all programmed remote controls. After accessing, press OK, it flashes, indicating that all remote controls have been removed. PROGRAMMABLE VALUES Mandatory for the Parking operating mode. -
Page 11: Detection Methods 10B
03. CONFIGURATION 03. CONFIGURATION OPERATING MODES OPERATING MODES DETECTOR MODE In this operating mode, it is possible to choose the colors that each traffic light should have in a resting situation. It is also possible to send an impulse to indicate an opening signal at the gate, as well as to The "detector"... - Page 12 03. CONFIGURATION 03. CONFIGURATION DETECTION METHODS DETECTION METHODS Detection only with DET inputs: The vehicle will be detected only when the entry status is changed for Detection with PUL and DET inputs without time: The vehicle will be detected only if DET1 and the seconds configured in "C1"...
- Page 13 10 seconds with the red light. The MCS01 allows the connection to external boards in order to control the color of the traffic lights through the "R", "G" and "B" inputs, as well as the opening and closing of a barrier/gate through an Traffic light 2 will be 15 seconds with green light, 3 seconds with output relay.
Need help?
Do you have a question about the MCS01 and is the answer not in the manual?
Questions and answers