Subscribe to Our Youtube Channel
Related Manuals for Motorline professional MC61SE
Summary of Contents for Motorline professional MC61SE
- Page 1 MC61SE MC61SE INSTALLER AND USER’S MANUAL INSTALLER AND USER’S MANUAL v5.2 REV. 12/2019...
-
Page 2: Table Of Contents
00. CONTENT 00. CONTENT 01. SAFETY INSTRUCTIONS INDEX INDEX ATTENTION: 01. SAFETY INSTRUCTIONS This product is certified in accordance with European Community (EC) safety standards. 02. CONNECTIONS SCHEME COMPONENTS CONNECTION TO THE CONTROL BOARD This product complies with Directive 2011/65/EU of the 03. -
Page 3: Safety Instructions
01. SAFETY INSTRUCTIONS GENERAL WARNINGS the motorized door or gate from being triggered involuntarily. • This manual contains very important safety and usage information. WARNINGS FOR TECHNICIANS very important. Read all instructions carefully before beginning the installation/usage procedures and keep this manual in a safe place •... - Page 4 01. SAFETY INSTRUCTIONS RESPONSABILITY • Attach the permanent label for the manual release as close as possible to the release mechanism. • Supplier disclaims any liability if: • Disconnect means, such as a switch or circuit breaker on the electrical •...
-
Page 5: Connections Scheme
02. CONNECTIONS SCHEME COMPONENTS CONNECTION TO THE CONTROL BOARD MENU C, page 7A 2 (present man activated) Use the last connectors to connect a N.A. push-button. 1 (photocells activated) Connect the NC contact of the photocells on the Note • The Auto Close and Follow Me function is no longer effective. last connectors or make a shunt. -
Page 6: Control Board
05. FUNCTIONS • Accepted codestype Rolling Code • Central dimensions 99x104,5 mm FUNCTION’S BOARD • Fuse The control board MC61SE has a menu that allows access to all automatic configurations. 04. REMOTE CONTROLS MÁX. MIN. FACTORY MENU FUNCTION STATE PAGE... -
Page 7: Automation Sensibility Programming 6A
05. FUNCTIONS 05. FUNCTIONS AUTOMATION SENSIBILITY PROGRAMMING OPENING AND CLOSING COURSE PROGRAMMING This menu allows to set the level of sensibility that you want in the motor operation. To make the opening and closing course programmation, the mechanical limit switches Maximum sensibility - 1 | Minimum sensibility - 9 must always be in tune. -
Page 8: Enable/Disable Photocells And Present Man 7A
05. FUNCTIONS 05. FUNCTIONS ENABLE/DISABLE SAFETY PHOTOCELLS AND PRESENT MAN PROGRAMMING AUTOMATIC CLOSING When photocells enabled, if any obstacle interrupt them (if the door is closing), the door will Option 0 disables the automatic closing, and the gate will close only if it receives an order reverse the direction. -
Page 9: Enable/Disable Condominium Function 8A
05. FUNCTIONS 05. FUNCTIONS ENABLE/DISABLE CONDOMINIUM FUNCTION ENABLE/DISABLE SERVICE DOOR 0-Disabled • When this function is activated, the control board will only work if the service door isclosed. • If you send an order to the gate completely open, it will close. If the door is open, the control board reject any opening or closing order. -
Page 10: Increase Or Decrease Deceleration 9A
05. FUNCTIONS 05. FUNCTIONS INCREASE OR DECREASE DECELERATION ENABLE/DISABLE FOLLOW ME The deceleration reduce the motor speed in the final part of the course (opening or closing). With the “Follow Me” function activated, whenever the photocells detect the passage of a Without deceleration - select the value 0 user/obstacle, the control board triggers the closing maneuver 3 seconds later. -
Page 11: Troubleshooting
06. TROUBLESHOOTING INSTRUCTIONS FOR FINAL CONSUMERS/TECHNICIANS Anomaly Procedure Behavior Procedure II Discovering the origin of the problem 1 • Remove the motor top cover; • Motor • Make sure you have • Still not working • Consult a qualified 2 • Measure the 24V output of the transformer to detect the fault location; doesn't work 230V power supply technician.
Need help?
Do you have a question about the MC61SE and is the answer not in the manual?
Questions and answers