Motorline professional MC15BA User& Installer's Manual
  1. Manuals
  2. Brands
  3. Motorline professional Manuals
  4. Control Unit
  5. MC15BA
  6. User& installer's manual
Motorline professional MC15BA User& Installer's Manual

Motorline professional MC15BA User& Installer's Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
EN
MC15BA
USER / INSTALLER MANUAL
v3.0
REV. 12/2016

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the MC15BA and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Motorline professional MC15BA

Summary of Contents for Motorline professional MC15BA

  • Page 1 MC15BA USER / INSTALLER MANUAL v3.0 REV. 12/2016...

  • Page 2: Table Of Contents

    00. CONTENT 01. SAFETY INSTRUCTIONS INDEX STANDARDS TO FOLLOW 01. SAFETY INSTRUCTIONS ATTENTION: STANDARDS TO FOLLOW This product is certified in accordance with European Community (EC) safety standards. 02. THE CONTROL BOARD TECHNICAL SPECIFICATIONS This product complies with Directive 2011/65 / EU of the European Parliament and of the Council, of 8 June 2011, on the restriction of the use of certain hazardous substances in PROGRAMMING PRE-RECOMENDATIONS electrical and electronic equipment.

  • Page 3: The Control Board

    02. THE CONTROL BOARD TECHNICAL SPECIFICATIONS TECHNICAL SPECIFICATIONS The MC15BA is a monophasic control board com a control system via incorporated rá- 04 • Locking device (NC) Closing push-button input (NO) dio, developed for the automation of electromechanical barriers. 05 • Common GND output It is possible to integrate on the central, a radio system which operates as a safety 06 •...
  • Page 4 02. THE CONTROL BOARD 02. THE CONTROL BOARD PROGRAMMING PRE-RECOMENDATIONS PROGRAMMING PRE-RECOMENDATIONS Limit-swiches: Magnetic lock or lightbulb: 07 and 09 • The center allows the connection of opening and closing limit- 03 and e 04 • this output allows a magnetic lock or a lightbulb connetion. (see switches (both in NC).

  • Page 5: Configuration

    03. CONFIGURATION 03. CONFIGURATION PROGRAMMING PRE-RECOMENDATIONS MAIN MENU • CODE | PROGRAMMING TRANSMITTERS • OBSTACLES DETECTION The control board only accepts Dip-Switch transmitters or MOTORLINE Rolling Code The control board has a VR2 trimmer, controlled by microprocessor, for transmitters, and it has a maximum capacity of 120 transmitters. When trying to pro- regulating the opposition force required for the detection of obstacles.

  • Page 6: Extended Menu 1

    03. CONFIGURATION 03. CONFIGURATION MAIN MENU EXTENDED MENU 1 02. Press SET button once to change the operating mode. Activate or change the pause time for automatic closure: The L.CORT LED will turn on/ turn off e a configuration is complete. 01.

  • Page 7: Extended Menu 1

    03. CONFIGURATION 03. CONFIGURATION EXTENDED MENU 1 EXTENDED MENU 2 • ACCESSING THE EXTENDED MENU 2 barrier will reverse the direction of operation until reaching the limit-switch. To access the options from Extended Menu 2, read the following instructions: Operation in Step-by-Step Mode (CODE LED OFF): 01.

  • Page 8: Components Test

    03. CONFIGURATION 04. COMPONENTS TEST MENU EXTENSO 2 SCHEME FOR CAPACITATOR • CODE PED | To detect which components have problems in an electromechanical barrier installa- PHOTOCELLS TEST tion, sometimes is necessary to conduct tests with a direct connection to a 110V or This test is performed before starting any operation.

  • Page 9: Photocells Test And Transmitters

    04. COMPONENTS TEST PHOTOCELLS TEST AND TRANSMITTERS • PHOTOCELLS TEST The control board is prepared to a safety device connection in accordance with the section 5.1.1.6 of standard EN 12453. In every maneuver is performed a test for the Security Device and the Lock. In case of a funtion/connection failure the motor doesn’t start and every LED’s remain in a intermittent mode, indicating the error.

  • Page 10: Troubleshooting

    05. TROUBLESHOOTING FINAL CONSUMERS INSTRUCTIONS SPECIALIZED TECHNICIANS INSTRUCTIONS Problem Procedure Behavior Procedure II Discovering the origin of the problem • Barrier • Make sure you • Still not working. • Consult a qualified 1 • Open control box and check control board and test them by problem is on the control board.

  • Page 11: Connection Scheme

    06. CONNECTION SCHEME COMPONENT CONNECTION TO THE CONTROL BOARD See diagram on page 11 Antenna Photocells RX - Recetor Receiver Limit-Switches Wall Button/ CLOSE Key Selector CODE CODE P. OPEN CMD AP. L CORT. PGM. AUT T. MOT T. MOT. P T.

  • Page 12: Flashing Light Connection

    06. CONNECTION SCHEME FLASHING LIGHT CONNECTION To remove the LED strip it is The positioning is based on the only necessary to remove the existing letters of the LED strip. two connecting points. It is considered as incorrect posi- tion when the letters are inverted (with the light sensor on the left).

Table of Contents