Stanley SCD12 Instruction Manual page 25

e. Maintain power tools. Check for misalignment or
binding of moving parts, breakage of parts and
any other condition that may affect the power
tools operation. If damaged, have the power tool
repaired before use. Many accidents are caused by
poorly maintained power tools.
f. Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges are
less likely to bind and are easier to control.
g. Use the power tool, accessories and tool bits etc.
in accordance with these instructions, taking
intoaccount the working conditions and the work
to be performed. Use of the power tool for operations
different from those intended could result in a hazardous
situation.
5. Battery tool use and care
a. Recharge only with the charger specified by the
manufacturer. A charger that is suitable for one type
of battery pack may create a risk of fire when used with
another battery pack.
b. Use power tools
designatedbattery packs. Use of any other battery
packs may create a risk of injury and fire.
c. When battery pack is not in use, keep it away from
other metal objects like paper clips, coins, keys,
nails, screws or other small metal objects that can
make a connection from one terminal to another.
Shorting the battery terminals together may cause burns
or a fire.
d. Under abusive conditions, liquid may be ejected
from the battery, avoid contact. If contact
accidentally occurs, flush with water. If liquid
contacts eyes, additionally seek medical help.
Liquid ejected from the battery may cause irritation or
burns.
6. Service
a. Have your power tool serviced by a qualified repair
person using only identical replacement parts. This
will ensure that the safety of the power tool is maintained.
7. Electrical safety
Your tool is double insulated; therefore no earth
wire is required. Always check that the main
voltage corresponds to the voltage on the rating
plate.
Warning! If the power cord is damaged, it must
be replaced by the manufacturer, authorized
STANLEY Service Center or an equally qualified
person in order to avoid damage or injury. If the
power cord is replaced by an equally qualified
person, but not authorized by STANLEY, the
warranty will not be valid.
only with specifically
LABELS ON TOOL
The label on your tool may include the following
symbols:
W ........
Read
Instructions
min .....
Manual
.....
Use Eye
Protection
.....
Use Ear
Protection
n .......
0
V ........ Volts
...... Class II
A ........ Amperes
Hz ....... Hertz
FEATURES (Fig. A and B)
This tool includes some or all of the following features.
1. Variable speed switch
2. Forward/reverse slider
3. Torque adjustment collar
4. Gear shifter
5. Chuck
6. Battery release button
7. Battery Pack
8. Worklight
9. Main handle
Fig. B
10. Charging indicator
ADDITIONAL POWER TOOL SAFETY WARNINGS
Warning! Additional safety warnings for drills and impact
drills.
f Wear ear protectors with impact drills. Exposure to
noise can cause hearing loss.
f Use auxiliary handles supplied with the tool. Loss of
control can cause personal injury.
f Hold power tool by insulated gripping surfaces
when performing an operation where the cutting
accessory may contact hidden wiring. Cutting
accessory contacting a "live" wire may make exposed
metal parts of the power tool "live" and could give the
operator an electric shock.
f Use clamps or another practical way to secure and
support the workpiece to a stable platform. Holding
the work by hand or against your body leaves it unstable
and may lead to loss of control.
f Before drilling into walls, floors or cellings, check for the
location of wiring and pipes.
f Avoid touching the tip of a drill bit just after drilling, as
it may be hot.
f This tool is not intended for use by persons (including
children) with reduced physical, sensory or mental
capabilities, or lack of experience and knowledge,
unless they have been given supervision or instruction
concerning use of the appliance by a person responsible
for their safety. Children should be supervised to ensure
that they do not play with the appliance.
ENGLISH (
Original Instructions)
Watts
.... Earthing
Terminal
minutes
.... Safety Alert
Alternating
Symbol
Current
.../min.. Revolutions
Direct
or Recipro-
Current
cation per
minute
No-Load
.... The charger
Speed
is intended
for indoor
use only.
Construction
25