JUKI AE-9 Instruction Manual page 30

スイッチ 2 を押して機能設定 No. を「168( 下糸残量検知機能 )」を選択し、
3)
押して設定値を「0( ミシン停止無効 )」又は「1( ミシン停止有効） 」にします。
スイッチ 2 を押してから電源スイッチを OFF にします。
4)
SC-510
機能 No.57 機能 No.167
0
1
2
(Caution) For the function setting procedure of any operation panel other than CP-18, refer to the Instruc-
tion Manual for the operation panel to be used.
1) Turn ON the power with
three seconds or more, the buzzer sounds to allow you to carry out service-level function setting.
(Indication item A displays the last item you have changed the setting.)
* If the display shown on the screen does not change, turn the power supply OFF and carry out operation 1)
again.
(Caution) Be sure to re-turn ON the power switch when one or more seconds have passed after turning it
OFF. If the power switch is re-turned ON immediately after turning it OFF, the sewing machine
may fail to operate normally. In such a case, be sure to turn ON the power switch again properly.
switch 2 . Select function number "167 (enable/disable bobbin thread remaining amount de-
2) Press
tecting function)." Press
switch 2 . Select function number "168 (bobbin thread remaining amount detecting function)."
3) Press
switch 4 to select the setting "0 (disable stopping of sewing machine) or "1 (enable stopping
Press
of sewing machine."
switch 2 . Then, turn OFF the power switch.
4) Press
SC-510
Function No. Function No.
57 167
0
1
2
SC-922
機能 No.168
0 0 下糸残量検知機能を無効にします。
下糸残量検知機能を有効にします。
1 0 下糸が無くなったことを検知してもミシンは停止しません。このと
き検知スイッチが点滅し、ブザーが「ピッピッピッピ」と鳴ります。
下糸残量検知機能を有効にします。
下糸が無くなったことを検知したらミシンは停止します。この
とき検知スイッチが点灯し、 ブザーが 「ピー」 と鳴ります。また、
1 1
ペダルによる押え上げ操作以外のミシン操作は出来なくなりま
す。縫製を再開したい場合は、検知スイッチを一回押して検知
スイッチを点滅させると、ミシン操作ができるようになります。
switch 7 held pressed. When you have kept the switch held pressed for
switch 4 to select the setting "1 (enable detecting device."
SC-922
Function No.
168
Bobbin thread remaining amount detecting function is set to
0 0
inoperative.
The bobbin thread remaining amount detecting function is enabled.
Sewing machine does not stop even when it is detected that
1 0
the bobbin thread has run out. At this time, the detecting
switch fl ashes on and off, and the buzzer sounds "four times".
The bobbin thread remaining amount detecting function is enabled.
Sewing machine stops when it is detected that the bobbin
thread has run out. At this time, the detecting switch is lit
up, and the buzzer sounds "one time". In addition, sewing
1 1 machine operations other than the presser lifting operation
by means of the pedal cannot be performed. When sewing
is desired to be reopened, press the detecting switch once
to make the detecting switch fl ash on and off. Then sewing
machine operation can be performed.
27
– –
スイッチ 4 を
動作
Motion