Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Assa Abloy ENTR
Summary of Contents for Assa Abloy ENTR
-
Page 2: Table Of Contents
Table of Content Package Content Tools Required ON/OFF Switch 2.3.1 Turning ENTR™ ON 2.3.2 Turning ENTR™ OFF 2.3.3 Default PIN Code Changing PIN Code Pairing Remote Control ENTR™ User Manual... - Page 3 Adding PIN Code Open Door Lock Door Delete PIN Code Delete all PIN Codes 5.10 Volume Control 5.11 Factory Reset 6. Fingerprint Reader Pairing Fingerprint Reader 6.4.1 Add Master 6.4.2 Set Finger 6.4.3 Set PIN Code Unlock Door ENTR™ User Manual...
- Page 4 6.13 Add Time Schedule 6.14 Edit Time Schedule 6.15 Volume Control 6.16 Double Security 6.17 Factory Reset 7. Smartphone App Pairing Smartphone 9. Sabbath Mode 10. ENTR™ Wire-free Charger 10.1 General 10.2 10.3 Door Unit Charging Cases Limited Warranty ENTR™ User Manual...
-
Page 5: Package Content
1.1 Package Content Baseplate & knob charger Electrical unit Magnet Cylinder screw Cylinder Panel screw M5 screw 1.2 Tools Requirements • 2mm Allen key • 3mm Allen key ENTR™ User Manual... - Page 6 Note: Do not hammer (or use any other excessive force) on the cylinder or knob when them into the door. • Turn the knob back to the zero Knob marks point upwards. Note: The knob will jump out when returned to zero Zero ENTR™ User Manual...
- Page 7 • Insert the key into the external side of the cylinder and turn one full turn. • Take the key out. Note: Verify that the gear is not pressed in. Gear not pressed in ENTR™ User Manual...
- Page 8 Press the knob and turn. If the knob can not be pressed or turned, disassemble the cylinder, adjust the cylinder's rectangle and reassemble. screw • Connect the data cable plug. • Assemble electrical unit as illustrated. • Tighten the electrical unit's panel screw. Data cable ENTR™ User Manual...
- Page 9 Knob Touchpad ON/OFF switch Mute (Green) Manual mode (Green) OK (Green) Door not closed (Red) Error (Red) ENTR™ User Manual...
-
Page 10: On/Off Switch
2.3 ON/OFF Switch • Turning the ENTR™ lock ON or OFF. 2.3.1 Turning ENTR™ ON Before turning ENTR™ ON, verify that the door is shut. • Move the switch to the ON Make sure that the knob is in the zero (see •... -
Page 11: Default Pin Code
15 seconds, for user's • 15 seconds of ENTR™ will idle. 2.5 Default PIN Code The lock's default factory PIN code is: 1 2 3 4 5 # Please note: • Default PIN code must be changed before process. -
Page 12: Changing Pin Code
Reenter [OK] illuminated. [Error] illuminated. [New PIN Code] [#], 2 short beeps 2 long Beeps for 1 second. for example: 1231234# New PIN Code is set. ENTR™ goes to menu mode Restart the process from step 1 ENTR™ User Manual... - Page 13 Type [PIN Code] [#]. side (see Press [1] for ENTR™ on side. Numeric blinking. Press [3] for ENTR™ on right side. ENTR™ on right side of the door side of the door Press [1] Press [3] ENTR™ User Manual...
- Page 14 Press [Cfg]. [OK] blinks once. The lock will carry out the 2 short beeps process. Illuminated turn 1. Remove the mechanical key from the cylinder. 2. Check that the door was closed properly or if lock was interfered. ENTR™ User Manual...
- Page 15 ENTR™ in Manual mode (w/o locking). Refer to 2. Remove any other magnets from the door. 3. Place the magnet according to 4. Consult your installer or contact ENTR™ Technical Support. Door frame Cylinder screw (M5) Magnet Note: The top point of the magnet should be approximately 20mm below the...
-
Page 16: Pairing Remote Control
Press [Add]. Numeric illuminated. for 3 seconds to Type [PIN Code] [#]. Numeric blinking. Press [1] to add remote control. Press the remote control Illuminated turn [OK] blinks for 15 seconds for remote control unit. Remote control ENTR™ User Manual... - Page 17 Touchpad and Fingerprint readers within the system. Press [Del]. Touch screen with palm or Type [PIN Code] [#]. for 3 seconds to Numeric illuminated. 1 long beep ENTR™ User Manual...
- Page 18 Press [Del] to [OK] blinks once. 2 short beeps Illuminated turn Note: Wall reader and smartphones connected to the ENTR™ lock will not be deleted. Toggle the sound signal to OFF or ON Touch screen with palm or Press [Mute]. [Mute] illuminated.
- Page 19 Touch screen with palm or Press [M A]. Type [PIN Code] [#]. for 3 seconds to [Manual] illuminated. Notes: the ENTR™ lock to Manual will disable • locking. • Follow the same procedure to set the ENTR™ lock to locking. ENTR™ User Manual...
- Page 20 (2) to unlock. Beep sound during doorknob Slide your on the recessed grooves on both sides of the ENTR™ front panel: • To open, slide downwards on the recessed grooves on both sides. • To lock, slide upwards on the recessed grooves on both sides.
-
Page 21: Touchpad Reader
[OK] is illuminated for 2 seconds. Important: Do not touch the Touchpad during the self-test procedure and lights are When need recharging, a red warning signal will blink rapidly and long beep will sound during every lock/unlock ENTR™ User Manual... -
Page 22: Pairing Touchpad Reader
To turn the Touchpad Reader ON press [#] for 5 seconds. The reader will perform a self-test, followed by series of beeps. LED blinks green, red, and Blue. 5.2 Pairing Touchpad Reader This procedure is done via the ENTR™ lock. See also: Pairing Remote Control. Touch ENTR™ lock screen with palm Press [Add]. - Page 23 15 seconds. 2 short beeps No beeps Touchpad Reader added. On Wall Reader: green LED illuminated and 2 beeps Start the process from step 1. • Fix the Touchpad Reader to the baseplate. • Tighten screw. Fixing screw ENTR™ User Manual...
-
Page 24: Touchpad Reader Master Pin Code
Press [ [Master PIN Code] for example: 1231234# [#], Press [11] [#]. PIN Code added PIN Code not added Green [OK] illuminated for 1 second, Red [Error] illuminated for 1 second, 2 short beeps 1 long beep ENTR™ User Manual... -
Page 25: Open Door
Press [22] [#]. All PIN Codes deleted All PIN Codes not deleted Green [OK] illuminated for 1 second, Red [Error] illuminated for 1 second, 2 short beeps 1 long beep Note: Master PIN Code can not be deleted ENTR™ User Manual... -
Page 26: Volume Control
Press [55] [#]. 5.11 Factory Reset will delete all PIN codes (master and personal) and will cut The reset Touchpad Reader from the ENTR™ lock. Touch Touchpad Reader's screen with palm Enter [Master PIN Code] [#]. Press [ [Master PIN Code] [#]. -
Page 27: Fingerprint Reader
The reader will self calibrate, which will be followed by a series of beeps and blinking LEDs. 6.3 Adjust Date & Time --/--/-- DEVICE --/-- 15/03/15 DATE/TIME DD/MM/YY hh:mm 11:00 Enter Date Press [OK] Enter Time Press [OK] Press [OK] ENTR™ User Manual... -
Page 28: Pairing Fingerprint Reader
6.4 Pairing Fingerprint Reader This procedure is done via the ENTR™ lock. See also: Pairing Touchpad Reader. Touch ENTR™ lock screen with palm Press [Add]. Numeric illuminated. for 3 seconds to Type [PIN Code] [#]. Numeric blinking. Press [1] to add the Reader. -
Page 29: Add Master
Type in [PIN Code], (4 to 10 digits) Retype [PIN Code] ENTER CODE ADD USER RETYPE CODE ENTER CODE SET CODE ****** ****** 4-10 digits 4-10 digits Press [OK] Press [OK] Press [OK] Matched Codes Mismatched Codes SUCCESS FAILED SET CODE INVALID ENTR™ User Manual... -
Page 30: Unlock Door
Fingerprint authorized: Blue LED blinks and unlock command is sent. Fingerprint not authorized: Red LED illuminates. The device goes to standby. USER CODE 23:49 03/01 FAILED Note: In the event, the unlocking fails, ENTR™ will display an unlock failed’ message. UNLOCK ENTR™ User Manual... -
Page 31: Lock Door
Fingerprint Reader Red LED illuminates for 1 second long wake-up beeps are BATTERY LOW USER CODE MASTER CODE SETTING Touch screen ****** USERS 23:49 03/01 23:49 03/01 Press [ Enter [Master PIN Code] [OK] or swipe over scanner ENTR™ User Manual... -
Page 32: Add User
4-10 digits Press [OK] for YES or [ Type [CODE] [OK] Retype [CODE] [OK] for NO Mismatched Matched Codes Codes SUCCESS FAILED INVALID SET CODE Process did not complete. All data typed in will be erased from memory. ENTR™ User Manual... -
Page 33: Delete User
Use [8 ▼ ] or [2 ▲ ] to Use [8 ▼ ] or [2 ▲ ] to Press [OK] Two beeps select: toggle between users. Green LED illuminates. [ENABLE USER] [OK] Press [OK]. Note: Repeat this procedure to disable a user ENTR™ User Manual... -
Page 34: Delete All Users
[ADD SCHED] [OK] SUNDAY SUNDAY Schedule 12:00-13:00 13:00 *-No OK-Yes Saved Press [OK] for YES or [ Enter END [OK] for NO Notes: 2. Press [ * ] to go back on every menu. 3. Press [ * ENTR™ User Manual... -
Page 35: Edit Time Schedule
Use [8 ▼ ] or [2 ▲ ] to Use [8 ▼ ] or [2 ▲ ] to Press [OK] Two beeps select: select: toggle between HIGH, Green LED illuminates. [DEVICE] [OK] [VOLUME] [OK] MEDIUM or LOW. ENTR™ User Manual... -
Page 36: Double Security
*-NO OK-YES *-NO OK-YES FACTORY Use [8 ▼ ] or [2 ▲ ] to Use [8 ▼ ] or [2 ▲ ] to Press [OK] Press [OK] Two beeps select: select: Green LED illuminates. [DEVICE] [OK] [FACTORY] [OK] ENTR™ User Manual... -
Page 37: Smartphone App
7. Smartphone App • Android smartphone users: go to Google Play to download the ENTR™ System requirements: Android 4.4 • iOS (iPhone/iPad) users: go to the app store to download the ENTR™ System requirements: iOS 7.0 or higher • Bluetooth low-energy compliant The below message will be displayed when opening the ENTR™... -
Page 38: Pairing Smartphone
Illuminated turn ENTR™ will be visible for 5 min. Open the ENTR™ app and follow the steps described in order to pair the smartphone with the ENTR™ lock. ENTR™ App User Manual is available for download at: www.entrlock.com ENTR™ User Manual... - Page 39 Release the lid by safely a small tool into the notch (1), and press the lid clasp (2). Notch Clasp b. Take out the push and intermediate part. c. Take out the electronic board with the and remove ENTR™ User Manual...
- Page 40 Insert the electronic board into the remote control’s housing (2). c. Reassemble the intermediate part and the push and place over the electronic board. d. Place the lid and press the clasp clicks into place. Clasp ENTR™ User Manual...
-
Page 41: Sabbath Mode
LED blinks every 20 seconds. Touch screen with palm or Press [Cfg]. Numeric illuminated. for 3 seconds to Type [PIN Code] [#], Numeric blinking. Sabbath mode Sabbath mode Press [5] to toggle between of the Sabbath mode. ENTR™ User Manual... -
Page 42: Entr™ Wire-Free Charger
10. ENTR™ Wire-free Charger 10.1 General The "ENTR™ Wire-free Charger" is used to charge the Door Unit on the door. The device is being charged by wired charger. The charging of the Door Unit is done through a cable with micro-USB male connector. -
Page 43: Cases
2. Check that the electronic unit is properly the cylinder. 3. Please consult with your locksmith/installer to ensure proper was completed. I've ENTR™, but when I slide my 1. Redo the process. down, the door locks; and when I 2. Pay to the door's... - Page 44 The power adaptor is not charging the Make sure you are using the dedicated ENTR™ power door unit. adaptor that was supplied with your lock. Standard 5V power adaptors WILL NOT charge the unit.
- Page 45 ENTR™. 2. Refresh the app. 3. Only one phone can connect to ENTR™ at the same It's possible that another user's phone is already connected to ENTR™. If so, close the app on any other user's phone.
-
Page 46: Limited Warranty
Dealer, to Mul-T-Lock®, either directly, or through the Dealer from whom Purchaser purchased the Product. All shipping, handling, travel, service call and/ or other incidental and/or related charges are fully payable by Purchaser only and are not included in this limited warranty. ENTR™ User Manual... - Page 47 +80C, Internal -10C to +50C) • The cylinder’s keyway should be lubricated at least once per year (preferably using lubricants authorized by Mul-T-Lock®, or light machinery oil). In any heavy use environments, extreme weather must be conducted every three months. ENTR™ User Manual...
Need help?
Do you have a question about the ENTR and is the answer not in the manual?
Questions and answers