Advertisement
Quick Links
Radio control model
R/C Flugmodell
INSTRUCTION MANUAL
MONTAGEANLEITUNG
Designed for brushless electric motors
Entwickelt für Brushless Elektro Motoren
TECHNISCHE DATEN
Spannweite
Lange
Elektroantrieb
Verbrennerantrieb
Fernsteuerung
SPECIFICATIONS
Wingspan
Length
Electric Motor
Glow Engine
.46 2Stroke / .52 4-Stroke
Radio
6 Channel / 6-7 Servos
WARNING! This radio controlled model is NOT a toy. If modified or flown carelessly it could go out of controll and
cause serious human injury or property damage. Before flying your airplane, ensure the air field is spacious enough.
Always fly it outdoors in safe areas and seek professional advice if you are unexperienced.
ACHTUNG! Dieses ferngesteuerte Modell ist KEIN Spielzeug! Es ist für fortgeschrittene Modellflugpiloten bestimmt,
die ausreichende Erfahrung im Umgang mit derartigen Modellen besitzen Bei unsachgemäßer Verwendung kann
hoher Personen- und/oder Sachschaden entstehen. Fragen Sie in einem Modellbauverein in Ihrer Nähe um
professionelle Unterstützung, wenn Sie Hilfe im Bau und Betrieb benötigen. Der Zusammenbau dieses Modells ist
durch die vielen Abbildungen selbsterklärend und ist für fortgeschrittene, erfahrene Modellbauer bestimmt.
1620mm
1250mm
(siehe nächste Seite)
7.5cc 2-T / 8.5cc 4-T
5 Kanal / 4 -5 Servos
63.7in.
49.2 in.
(See next page)
TRI - PACER
PIPER PA-22
(.46-.52 class glow conversion optional)
(7,5 -8,5cc Glühzündermotor Einbau möglich)
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for Nexa Tri-Pacer Piper PA-22
Summary of Contents for Nexa Tri-Pacer Piper PA-22
- Page 1 Radio control model TRI - PACER R/C Flugmodell PIPER PA-22 INSTRUCTION MANUAL MONTAGEANLEITUNG Designed for brushless electric motors (.46-.52 class glow conversion optional) Entwickelt für Brushless Elektro Motoren (7,5 -8,5cc Glühzündermotor Einbau möglich) TECHNISCHE DATEN Spannweite 1620mm Lange 1250mm Elektroantrieb (siehe nächste Seite) Verbrennerantrieb 7.5cc 2-T / 8.5cc 4-T...
-
Page 2: Conversion Table
REQUIRED FOR OPERATION (Purchase separately) BENOTIGTE KOMPONENTEN (Nicht im Lieferumfang enthalten) Propeller 11x8 for electric motor / 11x6 for glow engine Luftschraube 11x8 fur Elektromotor / 11x6 fur Verbrennungsmotor Extension cord Servoverlangerungskabel Minimum 6 channel radio for airplane / 7 servo Motor x1, rudder x1, elevator x1 aileron x2 (mini servo) Flap x2 (mini servo) Brushless Motor... - Page 3 Securely attach the engine mount to the Move the magnetic canopy out of the fuselage. fire-wall using the four 4x25mm screws. Note the side thrust for motor! Sturz und Zug beachten! Align the mark on both mounts with the center Magnetic pieces mark on the fire-wall Set the engine on the...
- Page 4 Using a plywood motor mounting plate as a template, mark the fire wall where the four holes are to be drilled . Remove the plywood motor mounting plate and drill a 13/64” 13/64”(5mm) hole through the fire-wall at each of the four marks marked above.
-
Page 5: Horizontal Stabilizer
Cut two slots (3x7mm and 3mm deep) along the trailing edge of the horizontal stabilizer. TOP VIEW / Draufsicht HORIZONTAL STABILIZER TOP VIEW / Draufsicht 85mm 85mm Full the elevator out of the horizontal stabilizer. Cut away only the film both side When you are satisfied with the alignment, use a pencil to trace around the top and bottom of the stabilizer where it meets the... - Page 6 Install the horizontal stabilizer into the fuselage and adust the alignment as described in steep 4B. Secure the horizontal stabilizer in place using CA glue. Aluminum wing joiner B=B’ B’ Note: the hole on the center of the stabilizer must be coincidental with the center line of the fuselage.
- Page 7 10mm Cut a slots (3x7mm and through both the covering and balsa wood) along the trailing edge of the vertical stabilizer. Cut away only the covering FRONT-VIEW Trial fit the vertical stabilizer in place. Check the alignment of the vertical stabilizer. If the parts will join, but with a gaps, sand or trim the parts a little at a time until the parts meet exactly with no gaps.
- Page 8 Mark 3mm screw ..4 3mm screw 3mm screw Aluminum landing gear Hauptfahrwerk BOTTOM - VIEW / Unteransicht Must be purchase separetely 4mm nut 4X40mm screw 4x40mm screw ....2 4mm nut-washer Aluminum landing gear...
-
Page 9: Top View
3x20mm screw ..4 NOSE WHEEL ARM NOSE WHEEL NOSE WHEEL PUSHROD NOSE WHEEL MOUNT (PLY) NYLON PUSHROD GUDER TOP-VIEW Securely attach the nose gear mount to the fire wall using the four 3x20mm screws (1) Insert the nylon pushrod guider tube and the nose gear push rod into the fuselage (2). Slide the nose gear push rod through the nose gear control horn (3). - Page 10 4mm nut 4x45mm screw Tipp Battery seat bell Akku Kiettband aus dem PICHLER Blow Sortiment Best.Nr. C4739 To muffler Water Filler tube Rubber stopper Checking for leaks - block the vents and blow into the feed - if in doubt submersing the tank To engine in a blow of water will show up any problems.
- Page 11 Magnetic seating (front seating only) Magnetic piece. Aluminum tube B’ Aluminum tube B=B’ Note: check the length (B=B’) of the aluminum tube with the fuselage before glue. Aileron extension Aileron pushrod cord 1.2mm O Alenk-Gestange Trial fit the control horn into the slot.
- Page 12 BOTTOM - VIEW / Unteransicht Cut away only the covering Assemble left and right side the same way...
- Page 13 Note: The hole on the surface of the top of the 2.mm drill bit wing are pre-drilledat factory. Secure the wing in place using 3x15mm screw. Aluminum 3x15mm screw tube inside 3x15mm screw ..2 Note: The hole on the surface of the top of the wing are pre-drilledat factory.
- Page 14 0.5mm dia. Cable ...1 roll 2mm metal tube .....4 Aileron 10mm 10mm Querruderausschlag 20mm Rudder Flap 20mm Seitenruderausschlag 15mm 10mm Elevator 65 ~ 70mm 10mm Hohenruderausschlag Do not try to fly an out-of balance model! Uberprufen Sie vor dem Flug den Schwerpunkt. IMPORTANT: Please do not clean your model with pure alcohol, only use liquid soap with water or use glass cleaner to clean on surface of your model to keep the colour not fade.
Need help?
Do you have a question about the Tri-Pacer Piper PA-22 and is the answer not in the manual?
Questions and answers