GE Profile Advantium SCA2001KSS Installation Instructions Manual
  1. Manuals
  2. Brands
  3. GE Manuals
  4. Microwave Oven
  5. Profile Advantium SCA2001KSS
  6. Installation instructions manual
GE Profile Advantium SCA2001KSS Installation Instructions Manual

GE Profile Advantium SCA2001KSS Installation Instructions Manual

Speedcook oven
Hide thumbs Also See for Profile Advantium SCA2001KSS:
Table of Contents

Advertisement

Quick Links

See also: Owner's Manual
Installation
Instructions
Questions? Call 800.GE.CARES (800.432.2737)

BEFORE YOU BEGIN

Read these instructions completely and carefully.
IMPORTANT –
•
for local inspector's use.
IMPORTANT –
•
codes and ordinances.
Note to Installer –
•
with the Consumer.
Save these instructions
Observe all governing
Be sure to leave these instructions
Speedcook Oven
or
Visit our Website at:
Note to Consumer –
•
future reference.
• Skill level – Installation of this appliance requires basic
mechanical and electrical skills.
• Proper installation is the responsibility of the installer.
• Product failure due to improper installation is not
covered under the Warranty.
KEEP THESE INSTRUCTIONS.
www.GEAppliances.com
Keep these instructions for
READ CAREFULLY.

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Profile Advantium SCA2001KSS and is the answer not in the manual?

Questions and answers

Related Manuals for GE Profile Advantium SCA2001KSS

Summary of Contents for GE Profile Advantium SCA2001KSS

  • Page 1: Installation Instructions

    Installation Instructions Questions? Call 800.GE.CARES (800.432.2737) BEFORE YOU BEGIN Read these instructions completely and carefully. IMPORTANT – • Save these instructions for local inspector’s use. IMPORTANT – • Observe all governing codes and ordinances. Note to Installer – • Be sure to leave these instructions with the Consumer.

  • Page 2: Table Of Contents

    Installation Instructions CONTENTS General information Important Safety Instructions ... 3 Electrical Requirements... 3 Hood Exhaust ... 4, 5 Damage—Shipment/Installation... 6 Parts Included ... 6 Tools You Will Need ... 7 Mounting Space ... 7 Step-by-step installation guide Placement of Mounting Plate ... 8–10 Removing the Mounting Plate ...

  • Page 3: Important Safety Instructions

    IMPORTANT SAFETY INSTRUCTIONS This product requires a 4-prong grounded outlet. The installer must perform a ground continuity check on the power outlet box before beginning the installation to insure that the outlet box is properly grounded. If not properly grounded, or if the outlet box does not meet electrical requirements noted (under ELECTRICAL REQUIREMENTS), a qualified electrician should be employed to correct any deficiencies.

  • Page 4: Hood Exhaust

    HOOD EXHAUST NOTE: Read these next two pages only if you plan to vent your exhaust to the outside. If you plan to recirculate the air back into the room, proceed to page 6. OUTSIDE TOP EXHAUST (EXAMPLE ONLY) The following chart describes an example of one possible ductwork installation. DUCT PIECES Roof Cap 12 Ft.
  • Page 5 Installation Instructions NOTE: If you need to install ducts, note that the total duct ″ x 10″ rectangular or 6″ diameter round duct length of 3 ⁄ should not exceed 140 equivalent feet. Outside ventilation requires a HOOD EXHAUST DUCT. Read the following carefully.

  • Page 6: Damage-Shipment/Installation

    Installation Instructions DAMAGE—SHIPMENT/ INSTALLATION • If the unit is damaged in shipment, return the unit to the store in which it was bought for repair or replacement. • If the unit is damaged by the customer, repair or replacement is the responsibility of the customer. •...

  • Page 7: Tools You Will Need

    Installation Instructions TOOLS YOU WILL NEED # 1 and #2 Phillips screwdriver Tin snips (for cutting damper, if required) Scissors (to cut template, if necessary) Gloves Saw (saber, hole or keyhole) Safety goggles MOUNTING SPACE ″ ⁄ 30″ 2 ″ 66″...

  • Page 8: Placement Of Mounting Plate

    Installation Instructions PLACEMENT OF THE MOUNTING PLATE REMOVING THE OVEN FROM THE CARTON/REMOVING THE MOUNTING PLATE Remove the box containing the installation instructions, filters, exhaust adaptor and the small hardware bag. Stand the oven on its control panel side. Use a portion of the carton or some other material to protect the outer case from being damaged.

  • Page 9: Determining Wall Plate Location

    Installation Instructions DETERMINING WALL PLATE LOCATION UNDER YOUR CABINET Plate position—beneath flat bottom cabinet Plate position—beneath recessed bottom cabinet with front overhang Plate position—beneath framed recessed cabinet bottom Mounting Plate Tabs Touching the Cabinet Bottom Your cabinets may have decorative trim that interferes with the oven installation.

  • Page 10: Aligning The Wall Plate

    Installation Instructions ALIGNING THE WALL PLATE Hole A Hole C CAUTION: Wear gloves to avoid cutting fingers on sharp edges. Draw a vertical line on the wall at the center of the 30″ wide space. Use the mounting plate as the template for the rear wall.

  • Page 11: Installation Types

    INSTALLATION TYPES This oven is designed for adaptation to the following 3 types of ventilation: A. Outside Top Exhaust (Vertical Duct) B. Outside Back Exhaust (Horizontal Duct) C. Recirculating (Non-Vented Ductless) OUTSIDE TOP EXHAUST (VERTICAL DUCT) See page 12 See page 19 Installation Instructions (Choose A, B or C) NOTE: This oven is shipped assembled for Outside Top...

  • Page 12: Aoutside Top Exhaust

    Installation Instructions OUTSIDE TOP EXHAUST INSTALLATION OVERVIEW A1. Attach Mounting Plate to Wall A2. Prepare Top Cabinet A3. Install Adaptor A4. Mount the Oven A5. Adjust Exhaust Adaptor A6. Connect Ductwork ATTACH THE MOUNTING PLATE TO THE WALL Attach the plate to the wall using toggle bolts. At least one wood screw must be used to attach the plate to a wall stud.

  • Page 13: Preparation Of Top Cabinet

    Installation Instructions USE TOP CABINET TEMPLATE FOR PREPARATION OF TOP CABINET You need to drill holes for the top support screws, a hole large enough for the power cord to fit through, and a cutout large enough for the exhaust adaptor. •...

  • Page 14: Mount The Oven

    Installation Instructions MOUNT THE OVEN If your cabinet front hangs more than 2 cabinet bottom, you may need to use longer screws than the ones provided with this product. The screws provided with this product (hardware item 3) are self-aligning, large-head machine screws 1/4″...

  • Page 15: Boutside Back Exhaust

    Installation Instructions OUTSIDE BACK EXHAUST INSTALLATION OVERVIEW B1. Prepare Rear Wall B2. Attach Mounting Plate to Wall B3. Prepare Top Cabinet B4. Adjust Blower B5. Mount the Oven PREPARING THE REAR WALL FOR OUTSIDE BACK EXHAUST Place the mounting plate against the rear wall and align it with the holes drilled earlier.

  • Page 16: Attach Mounting Plate To Wall

    Installation Instructions ATTACH THE MOUNTING PLATE TO THE WALL Attach the plate to the wall using toggle bolts. At least one wood screw must be used to attach the plate to a wall stud. Remove the toggle wings from the bolts. Insert the bolts into the mounting plate through the holes designated to go into drywall and reattach the toggle wings to 3/4″...

  • Page 17: Mount The Oven

    Installation Instructions Gently remove the wires from the grooves. Reroute the wires through grooves on other side of the blower unit. Before Rerouting Wires Routed Through Right Side Wires Routed Through Left Side Rotate blower unit counterclockwise 180°. Before Rotation Back of Oven Roll the blower unit 90°...

  • Page 18: Mount The Oven

    Installation Instructions MOUNT THE OVEN NOTE: When mounting the oven, thread power cord through hole in bottom of top cabinet. Keep it tight throughout Steps 1–3. Do not pinch cord or lift oven by pulling cord. Rotate front of oven up against cabinet bottom.

  • Page 19: Recirculating

    Installation Instructions RECIRCULATING INSTALLATION OVERVIEW C1. Attach Mounting Plate to Wall C2. Prepare Top Cabinet C3. Adjust Blower C4. Mount the Oven C5. Install Charcoal Filter ATTACH THE MOUNTING PLATE TO THE WALL Attach the plate to the wall using toggle bolts. At least one wood screw must be used to attach the plate to a wall stud.

  • Page 20: Adapting Blower For Recirculation

    Installation Instructions ADAPTING BLOWER FOR RECIRCULATION NOTE: The exhaust adaptor with damper is not needed for recirculating models. You may want to save them for possible future use. Remove and save screws that hold the blower plate to the oven. Retaining Flange Blower Plate...

  • Page 21: Mount The Oven

    Installation Instructions Secure blower unit to oven with the screw removed in Step 2. Replace blower plate with the screws removed in Step 1. Blower Plate Screws Retaining Flange Blower Plate MOUNT THE OVEN FOR EASIER INSTALLATION AND PERSONAL SAFETY, WE RECOMMEND THAT TWO PEOPLE INSTALL THIS OVEN.

  • Page 22: Installing The Charcoal Filter

    Installation Instructions MOUNT THE OVEN Cabinet Front Cabinet Bottom Shelf Self-Aligning Screw Oven Top Attach the oven to the top cabinet. Insert 2 self-aligning screws through outer top cabinet holes. Turn two full turns on each screw. Tighten the outer 2 screws to the top of the oven. (While tightening screws, hold the oven in place against the wall and the top cabinet.) Install grease filters.

  • Page 23: Before You Use Your Oven

    BEFORE YOU USE YOUR OVEN Make sure the oven has been installed according to instructions. Remove all packing material from the oven. Install oven rack (turntable) in cavity. Replace house fuse or turn breaker back on. Plug power cord into a dedicated NEMA 14–30R wall receptacle.
  • Page 24 164D3370P269 49-40339-1 3828W5U0315 07-03 JR Printed in Korea...

This manual is also suitable for:

Sca2000fbb

Table of Contents