Related Manuals for Mahr Millimar C 1202
Summary of Contents for Mahr Millimar C 1202
- Page 1 Compact length measuring instrument Millimar C 1202 Quick guide Valid from firmware version 1.0.0.0 3722972 Mahr GmbH Carl-Mahr-Straße 1 37073 Göttingen Tel. +49 551 7073 0 info@mahr.com, www.mahr.com 1021...
- Page 2 Dear customer, Thank you for choosing a product by Mahr GmbH. We kindly request that you follow the instructions below to ensure the long-term precision of your instrument. We operate a policy of continuous improvement and are constantly developing our products. Therefore, it is possible that there may be slight differences between the text and illustrations in this document and the instrument in your possession, especially with regard to type designations.
- Page 3 The test and measuring equipment, for which the Millimar is used, are subject to inspection equipment monitoring. For this reason, regular inspection equipment monitoring performed by either the user or Mahr Service must ensure compliance with the specified error limits for the test and measuring equipment. Mahr GmbH • Millimar C1202...
- Page 4 Do not use an electric marking tool. Disposal information Electronic equipment which was purchased from Mahr after March 23, 2006 can be returned to us. We will dispose of this equipment in an environmentally-friendly way. The valid EU directives (WEEE, ElektroG) apply.
-
Page 5: Table Of Contents
Selecting the display language ..............15 Setting the measurement unit ..............15 Connecting the measuring probe ............... 16 Selecting the probe type ................16 Setting up the probe ..................18 Measuring screen ..................19 Switching OFF ..................... 19 Mahr GmbH • Millimar C1202... -
Page 6: Delivery And Connection
Delivery and connections Unpacking Mahr GmbH • Millimar C1202... - Page 7 Mahr GmbH • Millimar C1202...
-
Page 8: Scope Of Delivery
Millimar C 1202 – Power supply unit with inter- changeable adapter – Bus termination module – Micro SD memory card – Quick guide Bus termination module fitted in C 1202 Slot for Micro SD memory card Mahr GmbH • Millimar C1202... - Page 9 Module for 1 pneumatic measuring instrument 5331157 Millimar N 1701 PF-10000 Module for 1 pneumatic measuring instrument Up to two N 1701 PM and N 1701 PF measuring modules can be used at the same time. Mahr GmbH • Millimar C1202...
-
Page 10: Symbols
Data transfer Sequential, disabled sequential Data transfer Data transfer Parallel, disabled parallel Reduce the resolution Increase the resolution Reduce the resolution Increase the resolution Hold down Hold down Toggle function Toggle function Selecting a feature Mahr GmbH • Millimar C1202... - Page 11 Delete file from memory card “Time controlled” measuring mode Start measurement Pause measurement Stop measurement Reset max, min memory. Select feature Select feature disabled Hold down Hold down Toggle function Toggle function Start measurement Hold down Toggle function Mahr GmbH • Millimar C1202...
-
Page 12: Operating Elements And Interfaces
Operating keys Master measurement Measured value active Scale Warning limit Tolerance limit Unit Measuring channel active Feature 1 Scale end value Feature 2 Angle in degrees Feature 3 Key function Hand for selecting a feature Mahr GmbH • Millimar C1202... -
Page 13: Keys With Dual Function
Pressing the key for longer than two seconds toggles the function. „Parallel“ mode Second function Active function Increase scale resolution Reduce scale resolution Hand, select feature Start measurement in time controlled mode Master measurement Reset extreme value memory Mahr GmbH • Millimar C1202... -
Page 14: Mode Display For Master Measurement
Parallel mode => Master measurement is performed for all active features at the same time. 1.5.4 Ports Data output Foot switch port Mains connection Slot for Micro SD memory card Measuring probe input C1 and C2 Mahr GmbH • Millimar C1202... -
Page 15: Switching On
Select the relevant language with ▼ or ▲ – Confirm entry by pressing 4 key Setting the measurement unit – Select the relevant measuring unit with ▼ or ▲ – Confirm entry by pressing 4 key Mahr GmbH • Millimar C1202... -
Page 16: Connecting The Measuring Probe
Probe input C1 and C2 Press the ON/OFF key => Menu appears – Select Setup 3 with – Select submenu Probe type C1 with or ▲ ▼ – Select using key or exit submenu using Ó Mahr GmbH • Millimar C1202... - Page 17 The instrument is most accurate after approx. 30 minutes of operation. Inductive mea- suring probes should be mechanically set to the electrical zero point before the first measurement. To do this, use the setup mode that indicates the raw value or absolute value of the probe. Mahr GmbH • Millimar C1202...
-
Page 18: Setting Up The Probe
The value displayed is the direct value from the measuring sensor. – Adjust measuring probe mechanical- ly close to “0” – The scaling can be adjusted with the – Exit the settings menu by pressing key. Mahr GmbH • Millimar C1202... -
Page 19: Measuring Screen
C1202 using the ON/OFF key. – Press ON/OFF key for at least 2 sec- onds. The instrument switches off. The detailed operating instructions can be downloaded at www.mahr.com/products on the product page. Mahr GmbH • Millimar C1202... - Page 20 Mahr GmbH • Millimar C1202...