Grey Intelligent Key; Transport; Storage; Care And Maintenance - Kärcher B 150 R Manual

Draining the waste water
WARNING
Improper disposal of waste water
Environmental pollution
Observe the local waste water treatment regulations.
Note
The suction turbine switches off and the display shows
"" when the waste water tank is full.
1. Remove the waste water drain hose from the sup-
port and open the drain hose cover.
Illustration S
Waste water drain hose
1
2. Squeeze the end of the hose and lower it over the
disposal facility.
3. Adjust the strength of the waste water jet by squeez-
ing the end of the hose.
4. Rinse the waste water tank with clear water.
5. Close the drain hose cover.
6. Press the waste water hose into the support on the
device.
Waste water tank rinsing system (option)
1. Remove the waste water drain hose from the sup-
port and open the drain hose cover.
2. Close the cover of the waste water tank.
3. Connect a water supply hose to the water connec-
tion of the waste water tank flushing system.
4. Open the water inlet and rinse the waste water tank
for about 30 seconds.
5. Repeat the rinsing process 2 to 3 times if necessary.
6. Close the water inlet.
7. Disconnect the water supply hose from the device.
8. Close the waste water drain hose and press it into
the support.
Empty the coarse dirt container
A coarse dirt container is only present on R cleaning
heads.
1. Lift the coarse dirt container and pull it out.
2. Empty the coarse dirt container.
3. Reinstall the coarse dirt container.
Draining fresh water
1. Open the fresh water tank cap.
2. Drain the fresh water.
3. Clean the filter.
4. Fit the fresh water tank cap.
Shutting down the unit
1. Turn the key-operated switch to "OFF".
2. Remove the Intelligent Key.
3. Secure the device against rolling away.
4. Charge the battery if necessary.

Grey Intelligent Key

The grey Intelligent Key grants the supervisory staff ex-
tended authorizations and setting options.
1. Insert the Intelligent Key.
2. Select the desired function by turning the info button.
Transport journey
1. Set the program selector switch to "Transport trav-
el".
2. Press the Info button.
The following settings can be made in the Transport
travel menu:
● Resetting the maintenance counter
● Key management
● Choosing the brush shape
● After-running time
● Setting the battery type
● Standard setting
● Setting the language
● Switch menu
● Factory setting
Resetting the maintenance counter
If maintenance work shown in the display has been car-
ried out, the corresponding maintenance counter must
then be reset.
1. Turn the Info button until "Maintenance Cntr" is dis-
played.
2. Press the Info button.
The counter readings are displayed.
3. Turn the info button until the counter to be cleared is
highlighted.
4. Press the Info button.
5. Select "Yes" by turning the Info button.
6. Press the Info button.
The counter is cleared.
Note
The service counter can only be reset by Customer Ser-
vice staff.
The service counter shows the time until the next ser-
vice due by Customer Service.
Key management
The authorizations are assigned for each yellow Intelli-
gent Key used and the language of the display is set for
this Intelligent Key in the "Key Manager" menu item.
1. Insert the grey Intelligent Key.
2. Turn the info button until the "Key Manager" menu
item appears on the display.
3. Press the Info button.
4. Remove the grey Intelligent Key and insert the yel-
low Intelligent Key to be personalized.
5. Select the menu item to be changed by turning the
info button.
6. Press the Info button.
7. Select the setting of the menu item by turning the in-
fo button.
8. Confirm the setting by pressing the menu item.
9. Select the next menu item to be changed by turning
the info button.
10. After all settings have been made, call up the
"Save?" menu by turning the info button.
11. Press the Info button.
The authorizations are saved.
The "Key Manager continue?" display appears.
● Yes: Program another Intelligent Key
● No: Exit the key menu
12. Press the Info button.
Choosing the brush shape
This function is required when changing the cleaning
head.
1. Turn the info button until the "Brush Head" menu
item appears on the display.
2. Press the Info button.
3. Turn the info button until the desired brush shape is
highlighted.
4. Press the Info button.
5. To change the cleaning head, move the lifting drive
by turning the info button:
 "up": Lifting
 "down": Lowering
 "OFF": Stopping
6. Turn the info button until the "OFF" menu item is dis-
played.
7. Press the Info button.
The menu is exited.
The controller performs a restart.
After-running time
1. Turn the info button until the "After-Run Time" menu
item appears on the display.
2. Press the Info button.
3. Turn the info button until the desired function is high-
lighted.
4. Press the Info button.
5. Turn the info button until the desired after-running
time is displayed.
6. Press the Info button.
Setting the battery type
1. Turn the info button until the "Battery Menu" menu
item appears on the display.
2. Press the Info button.
3. Turn the info button until the desired battery type is
highlighted.
4. Press the Info button.
Standard setting
Parameter changes made in the individual cleaning pro-
grams during operation are reset to the standard setting
when the device is switched off.
1. Turn the info button until the "Basic Settings" menu
item appears on the display.
2. Press the Info button.
3. Turn the info button until the desired cleaning pro-
gram is highlighted.
4. Press the Info button.
5. Turn the Info button until the desired parameter is
highlighted.
6. Press the Info button.
The adjusted value flashes.
7. Set the desired value by turning the Info button.
8. Press the Info button.
Setting the language
1. Turn the info button until the "Language" menu item
appears on the display.
2. Press the Info button.
3. Turn the info button until the desired language is
highlighted.
4. Press the Info button.
Switch menu
The work light can be enabled or disabled in this menu.
1. Turn the Info button until "Switch Menu" is dis-
played.
2. Press the Info button.
3. Turn the Info button until "Work Light" is highlighted.
4. Press the Info button.
English
Factory setting
The factory settings for all cleaning parameters are re-
stored.
1. Turn the info button until the "Factory Settings"
menu item is displayed.
2. Press the Info button.
3. Turn the Info button until "Yes" is highlighted.
4. Press the Info button.
Adjusting parameters for cleaning programs
All parameters for cleaning programs are retained until
another setting is selected.
1. Set the program switch to the desired cleaning pro-
gram.
2. Press the Info button.
The first adjustable parameter is displayed.
3. Press the Info button
The adjusted value flashes.
4. Set the desired value by turning the Info button.
5. Confirm the changed setting by pressing the Info
button or wait until the set value is automatically ac-
cepted after 10 seconds.
6. Select the next parameter by turning the Info button.
7. After changing all desired parameters, turn the Info
button until the "Quit Menu?" menu item is dis-
played.
8. Press the Info button.
The menu is exited.

Transport

DANGER
Driving on slopes
Risk of injury
Observe the maximum permissible gradient when driv-
ing the device on slopes for loading and unloading pur-
poses (see chapter "Technical data").
Drive slowly.
CAUTION
Failure to observe the weight
Risk of injury and damage
Be aware of the weight of the device during transporta-
tion.
1. With the D cleaning head installed, remove the disc
brushes from the brush head.
2. When transporting in vehicles, secure the device
against slipping and tipping over according to the
applicable guidelines.
Illustration T
Lashing strap
1

Storage

CAUTION
Failure to observe the weight
Risk of injury and damage
Be aware of the weight of the device during storage.
ATTENTION
Frost
Destruction of the device through freezing water
Drain all water from the device.
Store the device in a frost-free location.
When choosing the parking space, take into account the
total weight of the device in order not to impair its stabil-
ity.
● This device may only be stored indoors.
● Fully charge the batteries before storing them for a
long period.
● Fully charge the batteries at least every month dur-
ing storage.

Care and maintenance

DANGER
Inadvertently starting up device
Risk of injury, electric shock
Turn the program switch to the "OFF" position.
Remove the Intelligent Key prior to all work on the de-
vice.
Pull out the charger mains plug.
Unplug the battery connector.
CAUTION
Risk of injury
The suction turbine continues to run after the device has
been switched off.
Do not work on the device until the suction turbine is no
longer running.
 Drain and dispose of the waste water and fresh wa-
ter.
Maintenance intervals
Each time after use
ATTENTION
Improper cleaning
Risk of damage.
Do not spray the device with water.
21