Advertisement
Quick Links
Installing the Balanced Body
Tower Retrofit
Please take time to inspect the box for shipping damage prior to assembly. If any issues are found, immediately contact our customer
service department at 1-800-PILATES or +1-916-388-2838.
Read each step thoroughly and look at the diagrams before starting assembly. It is important that you follow the steps as they are
described in these instructions.
PARTS LIST (INCLUDED)
TOOLS
⁄
" Allen wrench
3
16
⁄
" Allen wrench
5
32
⁄
" drill bit
5
16
21mm x 1/2" wrench
PARTS
Tower Bracket
L shaped corner brackets
Long Vertical Tubes (with eyebolts)
Short Horizontal Tube (eyebolts and
black safety strap)
Single D Loops
Roll Down Bar
Wooden Push Through Bar for slider
assembly
Green Spring with clips
Red Spring with clips
Blue Spring with clips
Long Red Spring with clips
Long Gray Spring with clips
Push Through Bar Slider assembly
Push Through Bar Slider shoulder bolt
CenterLine Safety Strap
(Please use this list to make sure you have all the parts listed. If you are missing
a part, please contact our customer service department at 1-800-PILATES or
+1-916-388-2838)
TOOLS NEEDED (NOT INCLUDED):
» Hammer or mallet
PART NO
QTY
» Power drill
GEN9280
1
» Socket wrench with
GEN9282
1
TOL1059
1
ALL0060
1
HARDWARE:
PART NO
QTY
Part Number
722-001
1
622-001
4
GEN9232
TRP0105
2
TRP0100
1
GEN9015
607-346
1 pair
GEN9305
710-011
1
210-050
707-288
1
GEN9021
SPR9000
1
SPR9001
1
210-512
SPR9004
2
SPR9246
2
GEN9013
SPR9245
2
N/A
2
210-216
619-203
2
607-355
1
214-000
CenterLine
®
⁄
" &
7
1
16
Open end wrenches will also work.
QTY
6
Eyebolt,
4
20
6
10
4
Carriage Bolt,
4
2
2
®
⁄
" sockets.
2
Part
⁄
"-20 x 3"
1
4
Bolt,
⁄
"-20 x 2"
1
4
Flat Washer,
⁄
"
1
4
Finish Washer
Lock Nut,
⁄
"-20
1
4
⁄
-18
5
16
Lock Nut,
⁄
-18
5
16
Flat Head Bolt
Knurled Knob
Contact Us
1-800-PILATES | +1-916-388-2838
pilates.com | info@pilates.com
400-355 | 01.30.19
Advertisement
Related Manuals for Balanced Body CenterLine Tower Retrofit
Summary of Contents for Balanced Body CenterLine Tower Retrofit
- Page 1 Installing the Balanced Body CenterLine ® ® Tower Retrofit Please take time to inspect the box for shipping damage prior to assembly. If any issues are found, immediately contact our customer service department at 1-800-PILATES or +1-916-388-2838. Read each step thoroughly and look at the diagrams before starting assembly. It is important that you follow the steps as they are described in these instructions.
- Page 2 1. Remove all bolts from each of the casters with a ⁄ ” wrench 5. Using the included ⁄ ” drill bit (TOL1059) and the remaining and the included ⁄ ” Allen wrench. Keep the castors, nuts hole in each corner bracket as a guide, drill four holes in the and bolts close by.
- Page 3 PTB directly downwards. The pins of the sliders should not come out of the holes. If the pins do not stay in the tube holes, the pull knobs need to be replaced; call Balanced Body for replacement parts.
- Page 4 CENTERLINE TOWER MAT CONVERSION: QUESTIONS? 1. Remove the shoulder rest knob and bolt, then push the Contact Balanced Body Technical Support at 1-800-PILATES or shoulder rest toward the carriage and pull up to remove the +1-916-388-2838. shoulder rest. Loosely assemble the knob and bolt on each shoulder rest and store them under the Reformer.