Related Manuals for SEPTENTRIO PolaRxS
Summary of Contents for SEPTENTRIO PolaRxS
- Page 1 ________________________________________________________________________________________________________ PolaRxS Product Family Hardware Manual Version 1.3.0 PolaRxS Product Family Hardware Manual v1.3.0...
- Page 2 ________________________________________________________________________________________________________ PolaRxS Product Family Hardware Manual Version 1.3.0 November 24, 2014 © Copyright 2000-2014 Septentrio nv/sa. All rights reserved. Septentrio Satellite Navigation Greenhill Campus, Interleuvenlaan 15G B-3001 Leuven, Belgium http://www.septentrio.com support@septentrio.com Phone: +32 16 300 800 Fax: +32 16 221 640...
-
Page 3: Table Of Contents
........................... 10 1.2.8 PWR ........................... 11 Log Button ..........................11 Status LEDs ..........................11 Cables ............................12 Internal Logging on SD Memory Card ................. 13 Applicable Software Package ....................13 Hardware Specifications ......................13 PolaRxS Product Family Hardware Manual v1.3.0... - Page 4 ________________________________________________________________________________________________________ CE NOTICE PolaRxS receivers carry the CE mark and are as such compliant with the 2004/108/EC - EMC Directive and amendments, 2006/95/EC - Low Voltage Directive, both amended by the CE-marking directive 93/68/EC. With regards to EMC, these devices are declared as class B, suitable for residential or business environment.
- Page 5 Statement 0001/WARNING: The power supply provided by Septentrio (if any) should not be replaced by another. If you are using the receiver with your own power supply, it must have a double isolated construction and must match the specifications of the provided power supply.
-
Page 6: Polarxs_Pro
By default, the receiver provides a 5V DC supply on the MAIN connector to feed the antenna. Other voltages can be imposed through pin ANT_EXT of the IN connector on the front panel (see section 1.2.6). The maximum supported current is 200mA. PolaRxS Product Family Hardware Manual v1.3.0... -
Page 7: Pps Out (Bnc)
REF OUT (BNC) This connector provides access to the 10-MHz reference signal from the internal ultra low noise OCXO. It is a sinusoidal signal with an unloaded peak-to-peak amplitude of 1.1V. Output impedance is 50 Ohms. PolaRxS Product Family Hardware Manual v1.3.0... -
Page 8: Front Panel Connectors
Signal ground (GND) Not connected Not connected Receive Data (RXD – input to the receiver ) Transmit Data (TXD – output from the receiver) Not connected The receiver behaves as Data Terminal Equipment (DTE). PolaRxS Product Family Hardware Manual v1.3.0... -
Page 9: Com2
COM4 TX COM3 RX COM3 TX Leave unconnected 1.2.3.2 USB mode This mode is selected by applying 5V DC to pin#7. Pin # Description Not connected USB D- Reserved USB D+ Reserved USB Vbus PolaRxS Product Family Hardware Manual v1.3.0... -
Page 10: Ethernet
<12.0V, the antenna power supply is taken from ANT_EXT. Warning: Exceeding 12.0V for V , or drawing more than 200mA from the antenna connector can permanently damage the receiver. 1.2.7 Pin # Description Reserved Reserved Reserved Reserved PolaRxS Product Family Hardware Manual v1.3.0... -
Page 11: Pwr
ON/OFF. When this pin is tied to pin#1, the receiver is always on, regardless of the state of the on/off button. If you are using a different power adaptor than the one provided by Septentrio, make sure that it can sustain a current of 1.5A. -
Page 12: Cables
Part #: 201202 USB cable to be connected to the COM3-4/USB connector. Cable Name: CBLe_ETH_MS Part #: 200418 Ethernet cable (straight) to be connected to the ETH connector. Cable Name: CBLe_ETH_MX Part #: 200417 PolaRxS Product Family Hardware Manual v1.3.0... -
Page 13: Internal Logging On Sd Memory Card
To prevent data corruption, logging is protected against accidental power outages. There is no need to unmount the SD memory card before switching off the receiver. Applicable Software Package The PolaRxS_PRO is compatible with Septentrio’s SSRC3 Software Packages. Hardware Specifications Power consumption: Nominal operation: 6.5W typical...
Need help?
Do you have a question about the PolaRxS and is the answer not in the manual?
Questions and answers