iWave iW-RainboW-G34D Quick Start Manual
  1. Manuals
  2. Brands
  3. iWave Manuals
  4. Motherboard
  5. iW-RainboW-G34D
  6. Quick start manual

iWave iW-RainboW-G34D Quick Start Manual

I.mx 8m mini or i.mx 8m nano sodimm som development platform
Hide thumbs Also See for iW-RainboW-G34D:
Table of Contents

Advertisement

Quick Links

Download this manual
i.MX 8M Mini or i.MX 8M Nano
SODIMM SOM Development Platform
iW-RainboW-G34D/G37D
Quick Start Guide

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the iW-RainboW-G34D and is the answer not in the manual?

Questions and answers

Related Manuals for iWave iW-RainboW-G34D

Summary of Contents for iWave iW-RainboW-G34D

  • Page 1 8M Mini or i.MX 8M Nano SODIMM SOM Development Platform iW-RainboW-G34D/G37D Quick Start Guide...
  • Page 2 Disclaimer iWave Systems reserves the right to change details in this publication including but not limited to any product specification without notice. No warranty of accuracy is given concerning the contents of the information contained in this publication. To the extent...
  • Page 3 Platform and start the evaluation. It provides the instructions for setting-up the Development Platform from the packed box. Development Platform Description The iW-RainboW-G34D- i.MX 8M Mini or iW-G37D- i.MX 8M Nano SODIMM Development Platform is a demonstration, development and experimentation platform based on the NXP’s i.MX 8M Mini or i.MX 8M Nano SoC.

  • Page 4: Environmental Compliance

    Safety Environmental Compliance iW-RainboW-G34D i.MX 8M Mini or iW-RainboW-G37D i.MX 8M Nano SODIMM Development Platform is designed by using RoHS and REACH c o m p l i a n t c o m p o n e n t s a n d m a n u f a c t u r e d o n l e a d f r e e production process.

  • Page 5: Quick Start Steps

    Quick Start Steps Step 1 - Unpacking Remove the Development Platform from antistatic cover and place it above the ESD free area. Use anti-static pad/mat with proper grounding to place the Development Platform. Don't touch inside surface of the circuit board. Avoid using board in extreme dust, humidity and temperature conditions.

  • Page 6: Step 2 - What's Inside The Box

    Step 2 - What's Inside The Box ? Make sure that, below deliverables are received without any physical damage. DVD* i.MX 8M Mini or i.MX 8M Nano DevKit USB OTG Cable 5V,2.5A Power Supply *DVD is optional in some Configuration...
  • Page 7 Software Release Note and Quick Start Guide (this guide). Before moving to next step, one must go through all the documents including Hardware User Guides and get familiar about the hardware section of iW-RainboW-G34D i.MX 8M Mini or iW-RainboW-G37M i.MX 8M Nano SODIMM Development Platform.

  • Page 8: Top View

    Step 4 -Quick View-SOM TOP View 1. Wi-Fi & BT Module 2. LPDDR4 3. i.MX 8M Mini or i.MX 8M Nano SoC 4. Micro SD Conn. BOTTOM View 6. eMMC...
  • Page 9 Step 5-Quick View-Carrier Board TOP View 1.Power Jack 2.Audio In/Out Jack HDMI Connector 4.RTC Header 5.Eth Jack & USB2.0 Conn.-1** 6.Eth Jack**&USB2.0 Conn.-2** 7.USB OTG Connector 8.Debug UART Connector 9.UART Header 10.Expansion Header CAN Header 12.GPIO Header BOTTOM View LVDS Back light Conn. 14.SODIMM Edge Conn.

  • Page 10: Step 6- Setting-Up

    Step 6- Setting-Up Debug Port Setting Connect Type-A end of USB cable to PC and Micro AB end of USB cable to Development platform's debug Micro USB connector(J8) as shown below. Install the driver for Debug Port in Host PC/Laptop using the below link.
  • Page 11 Connect the 5V power supply plug to the power connector (J2) of the iW-RainboW-G34D/G37D platform as shown below and switch ON the power supply. Once Power is applied to iW-RainboW-G34D i.MX 8M Mini or iW-RainboW-G37D i.MX 8M Nano SODIMM Development Platform, the Red Power LEDs in the i.MX 8M Mini or i.MX 8M...

  • Page 12: Operating System Support

    Step 7 - Test Environment setup User must go through "Software User Guide" and get familiar about software section of iW-RainboW-G34D-i.MX 8M Mini or iW-RainboW-G37D-i.MX 8M Nano SODIMM Development Board. Operating System Support Linux 4.14 (or higher) Android Pie 9.0 (or higher)
  • Page 13 Command Prompt (Android) Android Home Screen Linux Home Screen...
  • Page 14 Product Name : i.MX 8 QM/QP Pico ITX SBC Processor : NXP’s i.MX 8 QM/QP SoC RAM : 4GB LPDDR4* Application : Industrial Motor Control, Sensor Fusion, Industrial IoT, Complex consumer, medical, and industrial embedded computing applications RAM size is expandable. Contact iWave team for further details...

  • Page 15: Need More Help

    Email Write your technical quires to support.ip@iwavesystems.com Live Chat We provide Live Chat technical support to our customers. Contact your iWave sales window to enable Live Chat support. Phone Call us on : +91-80-26683700, 26781643, 26786245 Office Address iWave Systems Technologies Pvt. Ltd.
  • Page 16 Headquarters: INDIA JAPAN UNITED STATES iWave Systems Tech. Pvt. Ltd. iWave Japan, Inc. iWave US 7/B, 29th Main, BTM Layout 2nd Stage, 8F-B, Kannai Sumiyoshi Building, 1692 Westmont Ave., Campbell, Bengaluru-560076,India. 3-29, Sumiyoshi-cho, Naka-ku, Yokohama, CA95008 USA Ph: +91-80-26683700, 26781643 Kanagawa, Japan.

This manual is also suitable for:

Iw-rainbow-g37d

Table of Contents