KI Instruct All Terrain Sloped Landing Pad Kit Assembly Instructions

lower post
bushing
landing pad
post (longer,
back-side)
landing pad
mount bushing
#8 x / " 1 (upper)
2
screws
landing pad
(underside)
1 / -20 x 4 "
4
bolt
landing pad
post assembly
Figure 1 (shorter, instructor-side)
landing pad
post assembly
(longer, back-side)
1 / -20 x 4"
4
bolt
1 / " flat
4
washer
1 / -20"
4
nut
Figure 2
lower post
bushing
landing pad
landing pad
post assembly
post (shorter,
(longer, back-side)
instructor-side)
#8 x / "
screw
landing pad
mount bushing
1 / -20 x 1 / " 1
4 2
(upper)
bolt
document
#8 x / " 1
2
truss head screw
landing pad
(underside)
storage
tower
Assembly Instructions
Instruct Classroom Furniture
®
All Terrain Sloped & Flat Landing Pad Kits
®
October 2019
Sloped Landing Pad Kit
1. Carefully place the sloped landing
pad upside down onto a soft,
protective surface (Figure 1).
2. Locate the hardware pack for the
sloped landing pad and identify the
parts by referencing Figure 1. Take
special note of the two different sized
landing pad posts supplied and two
1
2
different sized attachment bolts.
Important: The shorter
landing pad posts and bolts
are to be installed to the front,
user-side of the storage tower.
The user-side has the document
ledge attached to it.
3. Align the mounting holes of the
document ledge with the mounting
ledge
holes on the underside of the landing
pad. Secure the ledge to the front
user-side of the pad using, three
#8 x / " truss head screws (Figure 1).
1
2
landing pad
post assembly
(shorter, instructor-side)
1 / -20 x 1 / " 1
4 2
bolt
1 / " flat
4
washer
1 / -20"
4
nut
Assemble units as described herein only. To do otherwise
may result in instability. All screws, nuts and bolts must be
tightened securely and must be checked periodically after
assembly. Failure to assemble properly, or to secure parts
may result in assembly failure and personal injury.
4. Insert two / -20 x 4" bolts and two
1
4
/ -20 x 1 / " bolts into the four
1 1
4 2
(upper) landing pad mount bushings
as illustrated (Figure 1).
5. Secure the upper bushings with the
shorter / -20 x 1 / " bolts to the
1 1
4 2
underside of the landing pad near
the document ledge using four
#8 x / " screws. Then secure the
1
2
upper bushings having the 4" bolts
to the underside at the rear of the
landing pad using four #8 x / "
1
2
screws (Figure 1).
Note: The top of all four
landing pad posts are angled
to correspond with the slope of
the landing pad on the storage
tower.
6. Place the lower post bushings down
onto the flat, bottom sides of the
landing pad posts (two tall, and two
short) as illustrated. Position the
shorter, landing pad posts/bushings
to the installed upper bushings
closest to the installed document
ledge. Take care to orient the angled
edge of the posts correctly to
match the slope of the landing pad
underside (Figure 1).
7. Repeat the above procedure with
the longer landing pad posts,
positioning them to the rear upper
bushings at the 4" bolt locations,
correctly matching the slope angle
(Figure 1).
8. Orient the landing pad with the
document ledge to the user-side
of the storage tower as illustrated.
Carefully position the landing pad
post assemblies with installed
bushings, posts & bolts such that the
four bolts insert down through the
four mounting holes in the top of the
tower (Figure 2).
9. From inside the tower, locate the
/ -20 bolts inserted through the top
1
4
and place a / " washer and / -20
1 1
4 4
nut onto each bolt. Tighten nuts
to secure landing pad to tower top
(Figure 2).