KI InTandem Leg-Mounted CPU Holder Assembly Instructions

Assembly Instructions
InTandem Table System
InTandem Leg-Mounted CPU Holder
CPU holder
base
foot
Figure 1
CPU holder
base
CPU
securing strap
Figure 2
Assembly Instructions
InTandem Table System
®
Leg-Mounted CPU Holder
December 2012
¾"
#14 x
self-drilling screw
leg
male
buckle
Assemble units as described herein only. To do otherwise
may result in instability. All screws, nuts and bolts must be
tightened securely and must be checked periodically after
assembly. Failure to assemble properly, or to secure parts
may result in assembly failure and personal injury.
Tools Required
?
Screw Gun, Battery, Charger
? Tools Required
3/8" Nut Driver Socket Bit
? • Screw Gun, Battery, Charger
7/16" Wrench
• / " Nut Driver Socket Bit
3
8
• / " Wrench
7
Note: The Large CPU Holder can be
16
used on 30" deep InTandem legs
Note: The Large CPU Holder can
and will accommodate single or
be used on 30" deep InTandem
double CPU widths of 5.5" – 9.0".
legs and will accommodate
The Small CPU Holder can be used
single or double CPU widths
on 24" and 30" deep InTandem legs
of 5.5" – 9.0". The Small CPU
and will accommodate single or
Holder can be used on 24" and
double CPU widths of 3.8" – 5.8".
30" deep InTandem legs and will
accommodate single or double
Note: Both the Large and Small CPU
CPU widths of 3.8" – 5.8".
Holders can be placed on left, right,
Note: Both the Large and Small
or center InTandem legs. While
CPU Holders can be placed on
orientation is not critical to the
left, right, or center InTandem
function of the holder, it may be
legs. While orientation is not
desirable to have the CPU holder
critical to the function of the
side (components with large
holder, it may be desirable
adjustment slots) toward the inside
to have the CPU holder side
of the desk to reduce the amount of
(components with large
overhang into an aisle at the end of a
adjustment slots) toward the
desk run.
inside of the desk to reduce the
amount of overhang into an aisle
1. Unpack the InTandem CPU holder
at the end of a desk run.
components and locate the
1. Unpack the InTandem CPU
hardware kit. Place the InTandem leg
holder components and locate
or desk assembly upside down on a
the hardware kit. Place the
soft, protective surface. Place the
InTandem leg or desk assembly
CPU holder base on the bottom
upside down on a soft, protective
surface of the table leg's foot.
surface. Place the CPU holder
Position the CPU holder base so that
base on the bottom surface of the
its back edge is slightly ahead of leg
table leg's foot. Position the CPU
column vertical tube and generally
holder base so that its back edge
parallel with the foot. Hold in place
is slightly ahead of leg column
and secure with two #14 x ¾"
vertical tube and generally
self-drilling screws (Figure 1).
parallel with the foot. Hold in
place and secure with two
2. Remove the male buckle from #14 x ¾" self-drilling screws
(Figure 1).
CPU securing strap and feed end
through small slot in CPU holder
2. Remove the male buckle from
base, across the foot, and through
CPU securing strap and feed
small slot in opposite wall. Replace
end through small slot in CPU
male buckle by feeding strap through
holder base, across the foot, and
opening nearest teeth and loop back
through small slot in opposite
and through outside opening.
wall. Replace male buckle by
Repeat for second strap (Figure 2).
feeding strap through opening
nearest teeth and loop back and
through outside opening. Repeat
for second strap (Figure 2).