Advertisement
Quick Links
Advertisement
Related Manuals for WATSON C9 Height Adjustable Desk
Summary of Contents for WATSON C9 Height Adjustable Desk
- Page 1 ASSEMBLY C9 Height Adjustable Desk 360.394.1300 watsonfurniture.com V.2.01 08/2020...
-
Page 2: Important Safety Instructions
This product is for use on a nominal 120-V circuit. Make sure that the product is connected to an outlet having the same configuration as the plug. No adapter should be used with this product. 2 C9 HEIGHT ADJUSTABLE DESK ASSEMBLY INSTRUCTIONS... - Page 3 Utility Power Support Rail Bracket Cable Tray Support Rail Worksurface Leg Motor Desk Switch Grommet NOTE: C9 File Pendant, Pencil/File Pendant, and Pencil/Box Pendant Storage cannot be used on 24” deep C9 desks. 3 C9 HEIGHT ADJUSTABLE DESK ASSEMBLY INSTRUCTIONS...
- Page 4 C9 Height Adjustable Desk Hardware & Tools Hardware M6-1.0x12mm Low 0.25x0.563 Plastic M4-0.7x18mm Top At tachment Cap Rail Nut ( 0001120 ) #8x5/8” Screw M6-1x12mm Nylock Profile Cap Screw Spacer ( 0001249 ) Socket Head Cap ( 0001156 ) (116754)
- Page 5 Attach Assembly to the Long Frame Rails Slide the long frame rails onto the leg assembly and secure them using 8 screws (0001140). Repeat this step for the other side. M6-1.0x12mm Low Profile Cap Screw ( 0001140 ) 5 C9 HEIGHT ADJUSTABLE DESK ASSEMBLY INSTRUCTIONS...
- Page 6 8” W Storage (Left-Hand) 15”W Storage (Right-Hand) M6-1.0x12mm Low Profile Cap Screw ( 0001140 ) 6 C9 HEIGHT ADJUSTABLE DESK ASSEMBLY INSTRUCTIONS...
- Page 7 M4-0.7 x 18mm M6-1.0x12mm 0.25 x 0.563 Socket Head Cap Plastic Spacer Low Profile Cap Screw ( 0001250 ) Screw ( 0001140 ) ( 0001249 ) 7 C9 HEIGHT ADJUSTABLE DESK ASSEMBLY INSTRUCTIONS...
- Page 8 Be sure to use the outermost holes in the bracket (a). Attach the utility power bracket assembly to the frame rail using 2 screws (0001140) (b). M6-1.0x12mm Low Profile Cap Screw ( 0001140 ) 8 C9 HEIGHT ADJUSTABLE DESK ASSEMBLY INSTRUCTIONS...
- Page 9 Clip the utility power unit into the utility power bracket assembly. No hardware is needed for this step. Hang Cable Tray Hang the Cable Tray by aligning the pins with the back cutout and lifting it over the catch. 9 C9 HEIGHT ADJUSTABLE DESK ASSEMBLY INSTRUCTIONS...
- Page 10 (until vertical). Note: if the motor is difficult to insert, rotate the assembly clockwise until it will insert into the corner and rotate back counterclockwise until the motor assembly will snap into the rail. 10 C9 HEIGHT ADJUSTABLE DESK ASSEMBLY INSTRUCTIONS...
- Page 11 Finally, secure the control box in place with one screw (125293) and nut (888152). M6-1.0x40mm Cap M6-1x12mm Nylock Nut ( 888152) Screw (125293) Switch Cable Leg Motor Cables Leg Motor Cable Power Cable 11 C9 HEIGHT ADJUSTABLE DESK ASSEMBLY INSTRUCTIONS...
- Page 12 Attach screws (0001140) through the top clip into the worksurface. Repeat for a total of (10) caps. Top At tachment Cap M6-1.0x12mm Low ( 0001156 ) Profile Cap Screw ( 0001140 ) 12 C9 HEIGHT ADJUSTABLE DESK ASSEMBLY INSTRUCTIONS...
-
Page 13: Install Control Switch
Install Control Switch Insert the control switch into the cutout on the underside of the worksurface with two wood screws (116754). Note the orientation to ensure a proper fit. #8x5/8” Screw (116754) 13 C9 HEIGHT ADJUSTABLE DESK ASSEMBLY INSTRUCTIONS...