BEC M2M MX-1000e Quick Install Manual

WHAT'S IN THE BOX
1 x BEC MX-1000(e) M2M Router
1 x This Quick Install Guide
1 x Mounting Bracket
1 x MiniFIT to DC Jack Power Cable
1 x Vehicle Power Cable
1 x DC Power Adapter 12VDC 1.2A
2 x Wi-Fi Antennas
1
Insert the SIM Card
Note: Power o the MX-1000(e) before inserting/removing the SIM
Remove the SIM cover
WIFI WIFI
then insert the SIM card(s)
WIFI WIFI
WIFI
(2FF) with the mental
MINI
WIFI
WIFI ON/OFF USB2
MINI
contacts (gold plate) facing
WIFI ON/OFF USB2
RESET
RESET
up to the SIM slot(s) then
push it all the way in until
you hear the clicking sound. Replace the metal SIM cover
after inserting the SIMs.
2
Attach the Wi-Fi Antennas
Note: Use the plastic red caps to cover unused antenna ports
Screw the 2 female Wi-Fi
antenna cable connectors
until fully attached to the
Wi-Fi ports on MX-1000(e).
Do not over-torque the
antenna on the connector.
3
Attach the LTE & GPS Antennas
Note: 1. Use the plastic red caps to cover unused antenna ports
2. GPS and 3G/4G-LTE antenna(s) sold separately
Screw the male SMA
3G/4G-LTE and/or GPS
antennas tight to the
female connectors.
WAN1 WAN1
MAIN MAIN
Connect to the MAIN port,
the primary cellular antenna
port to transmit and
receive signal, if decide to
use a single LTE antenna.
Do not over-torque the antenna on the connector.
4
Connect to Mini USB Ports
Note: Software programming tool is required for the Mini USB interface
Connect to Mini USB port(s)
for direct connection to the
Cellular module(s) for
management – debug,
change firmware, and
configuration.
(Optional Accessories)
3G/4G Antennas
Active GPS Antenna
Ethernet (RJ-45) Cable
SETTING UP THE ROUTER
MINI
USB1
MINI
USB1
SIM2 SIM1
SIM2 SIM1
WAN1 WAN1
WIFI WIFI
MAIN MAIN
WIFI
WIFI
WIFI ON/OFF
WAN1 WAN1 WAN1 WAN1 WAN2 WAN2 WAN2 WAN1 WAN1
GPS GPS GPS
MAIN MAIN MAIN MAIN AUX AUX AUX AUX
WAN1 WAN2 WAN1
GPS
MAIN AUX AUX
POWER INTERNET USB1 USB2 GPS WAN1
POWER
1 2 Gb ETH 3
MINI MINI
USB2 USB1
5
Connect to Power Source
Use the DC Power Adapter
Attach the power cable
with 4-pin miniFIT to
DC jack power cable
the MX-1000(e) and plug
in the supplied DC
power adapter.
Use Vehicle Electrical System (Power & Ignition Sensing)
Attach the Vehicle power cable to
the MX-1000(e) and connect the
wire leads of the power cable to
WIFI WIFI
WIFI vehicle's electrical system.
MINI MINI
USB2 USB1
RESET
BLACK Wire (PIN 1 & 2):
SIM2 SIM1
Ground (GND). Use one
of the BLACK wires for
a neutral or ground
connection
WHITE Wire (PIN 3): ACC/ON for Ignition Input wire need to be
connecting into vehicle accessory wire.
RED Wire (PIN 4): VCC/OFF Voltage wire to the battery.
DC power range from 0V to 56V.
WAN1 WAN2 WAN2 WAN2 WAN2 WAN2 WAN2
AUX AUX MAIN MAIN MAIN MAIN MAIN MAIN
WAN2
MAIN
WAN2
2
4
3
6
Access to the MX-1000(e)
Access to the MX-1000(e) Web interface by entering
http://192.168.1.254 in the address bar of the web browser.
Default Login Information: Username (admin) and Password
(A unique12-digit password can be found on the device label).
The Quick Start Wizard provides key steps to connect the
MX-1000(e) to the Internet.
Model: MX-1000(e)
Quick Install Guide
GND VCC
Battery
PIN De nition Details
1
1 Ground
2 Ground
4
3 ACC Input
10~56VDC
4 VCC
M M
2
POWER
POWER
Ignition Switch
ACC
Fuse
Wire color
- Black
- Black
White
Red