BEC MX-210NP Quick Start Manual
  1. Manuals
  2. Brands
  3. BEC Manuals
  4. Network Router
  5. MX-210NP
  6. Quick start manual

BEC MX-210NP Quick Start Manual

4g/lte broadband router with poe
Hide thumbs Also See for MX-210NP:
Table of Contents

Advertisement

Quick Links

See also: User Manual
BEC MX-210NP
4G/LTE Broadband Router with
PoE
Quick Start Guide

Advertisement

Table of Contents
loading

Related Manuals for BEC MX-210NP

Summary of Contents for BEC MX-210NP

  • Page 1 BEC MX-210NP 4G/LTE Broadband Router with Quick Start Guide...
  • Page 3 BEC MX-210NP 4G/LTE Broadband Router with PoE PLEASE READ THE QUICK START GUIDE AND FOLLOW THE STEPS CAREFULLY. THIS QUICK START GUIDE WILL HELP YOU INSTALL THE DEVICE PROPERLY AND AVOID IMPROPER USAGE. IF YOU NEED MORE INFORMATION ON THIS SOFTWARE...

  • Page 4: Front Panel Leds

    No signal and the cellular module is in service No LTE module or LTE module fails Green & MX-210NP is either in debug mode or in upgrading firmware process Orange Green IP address has received; traffic is passing thru the device.

  • Page 5: Rear Panel Connectors

    Manually screw the GPS antenna tight to the female connector. Insert the mini SIM card (2FF) with the gold contact facing down. SIM Card Slot Push the mini SIM card (2FF) inwards to eject it * Power off the MX-210NP before inserting or removing the SIM card(s)

  • Page 6: Hardware Connection

    Quick Start Guide Hardware Connection WAN: 4G/LTE | Power Source: DC Power (ON) | LAN: Ethernet Devices II. WAN: 4G/LTE | Power Source: PoE Injector (OFF). LAN1: Connect with the PoE injector | LAN2: Ethernet Device (notebook, switch, etc.) III. WAN: Ethernet WAN (LAN2) | Power Source: DC Power Adapter (ON). LAN1: Ethernet Device (notebook, switch, etc.) | LAN2: Wireline Modem...
  • Page 7 BEC MX-210NP 4G/LTE Broadband Router with PoE Hardware Installation Power Connection Select power source from using a (1) DC power adapter or (2) PoE Injector 1.1 Using the Supplied DC Power Adapter Plug in the supplied power adapter to the wall jack, the other side to the MX-210N then power it ON the by pressing the Power On/Off button.
  • Page 8 Plug the RJ-45 Ethernet cable to one of the Ethernet ports, and the other side to the PC’s Ethernet interface. 3. WAN Link Interface and Connection BEC MX-210NP supports failover and failback on multiple WAN interfaces, 4G/LTE and EWAN. <Please refer to User Manual for detailed Internet setup> 3.1 Mobile 4G/LTE Connection Slide the SIM card into the card slot of the device with the gold contact facing down.
  • Page 9 BEC MX-210NP 4G/LTE Broadband Router with PoE 3.2 Ethernet WAN Connection Connect RJ-45 Ethernet cable to the EWAN port, and connect the other side to another alternative broadband device, such as Cable Modem, VDSL, Fiber Modem or PON optic lines.

  • Page 10: Connecting To The Router

    Quick Setup Your Router Use the Quick Start for fast connection setup. Wired Broadband Connection - before start configuring the MX-210NP, make sure you have the EWAN connected with your Internet box or fiber line. Step 1: Change administration password Setup a new password for “admin”...
  • Page 11 BEC MX-210NP 4G/LTE Broadband Router with PoE Step 3: Setup Wireless Connection Access Point: select Activated SSID: Assign a unique name Channel: pick from 1~11 Security Type: select a mode - Disable (No security) - WPA - WPA2 (Most secure one)

  • Page 12: Troubleshooting

    Quick Start Guide Troubleshooting 1. None of the LEDs are on when you turn on the router. Check the connection between the adapter and the router. If the error persists, you may have a hardware problem. In this case you should contact technical support. 2.

Table of Contents