Table of Contents
Advertisement
Handling precautions
General
■ SC-04J is waterproof/dustproof; however, do not allow water
(drinking water, perspiration, seawater, urine of pet animals, etc.)
or dust to enter this terminal or come in contact with accessories
or optional devices.
Adapter, docomo nano UIM card and external TV antenna cable are not
waterproof/dustproof. Do not use them in places with high humidity
such as a bath or where rain may get it wet. If you carry the terminal
close to your body, moisture from sweat may corrode the internal parts
causing a malfunction. Note that if a trouble is diagnosed as exposure
to water or other liquid, repairs of the terminal may not be covered by the
Warranty. For repairs, contact "Repairs" on the last page of this manual (In
Japanese only) or DOCOMO specified repair office.
■ Clean the terminal with a dry soft cloth (such as a cloth for eyeglasses).
• Rubbing it roughly with a dry cloth may scratch the display.
• Drops of water or dirt left on the display may cause stains.
• If the terminal is wiped with alcohol, paint thinner, benzine or detergent,
the printing may disappear or color may fade.
■ Clean the jacks or the fingerprint sensor occasionally and use the
terminal in a clean state.
If the jack etc. is dirt, you may not use the terminal normally.
When cleaning, be careful not to damage the terminals.
■ Do not place the terminal near an air-conditioner outlet.
The rapid change in temperature may cause condensation, causing
internal corrosion and malfunction.
■ Do not apply excessive force to the terminal.
Putting the terminal into a tightly packed bag or sitting on the terminal
in your pocket might damage the display or internal circuit board
resulting in a malfunction.
Also, keeping an external device connected to the external connection
terminal might damage the connector resulting in a malfunction.
■ Use the optional products specified by NTT DOCOMO for your
terminal.
If you use optional products other than specified, it may cause
malfunction or damage.
■ Read the instruction manuals supplied with individual optional devices.
■ Do not drop or give a strong impact to the terminal.
May cause malfunction or damage.
The terminal
■ Do not press display surface forcibly, or not operate with a sharp
pointed objects.
Doing so may cause a malfunction or damage of display.
■ Do not use the terminal in extremely hot or cold places.
Use the terminal within a temperature range of 0℃ to 35℃ and a
humidity range of 0% to 95%.
■ The terminal may affect land-line phones, TVs or radios in use
nearby, so use it as far as possible from these appliances.
■ Keep the information that you registered in the terminal separately
by backing up to microSD card, PC, cloud, etc. or noting down.
If the data is deleted, DOCOMO assumes no responsibility for the loss
of any data.
■ Do not plug external devices into the external connection jack at
a slant, or do not pull it forcibly while it is plugged.
May cause malfunction or damage.
■ It is normal for the terminal to become warm during use or charging.
Continue to use it.
■ Do not leave the camera lens under direct sunlight.
May cause discoloring or burn-in of elements.
■ Usually, close the docomo nano UIM card/microSD card tray tightly
during use.
Not doing so may cause malfunction due to entering foreign objects
such as liquid like water (drinking water, perspiration, seawater, urine of
pet animals, etc.) or dust to the terminal.
■ Do not give strong force to the fingerprint sensor or scratch the
surface of it.
May cause damage to the fingerprint sensor or cause the terminal to be
unavailable to perform the authentication.
■ While microSD card is being used, do not take the card out or do
not turn off the terminal.
May cause data loss or malfunction.
■ Do not bring magnetic cards or magnetic objects, etc. close to the
terminal.
Magnetic data in cash cards, credit cards, telephone cards, floppy disks,
etc. may be erased.
Bringing strong magnetism close to the terminal may cause malfunction.
■ Do not decorate the terminal sensor with film or sticker.
May cause the functions that use the proximity/light sensor to malfunction.
For the position of the proximity/light sensor, refer to the following.
→ P.21 "Part names and functions"
14
Contents/Precautions
Advertisement
Table of Contents
